STMicroelectronics

LM2902WYPT - 1.3MHz Quad Op Amp | STMicroelectronics

MPN: LM2902WYPT ✓ فعال
100 dB Vdss 375 uA Id 14-TSSOP Package Internal Speed
MOQ: 1 |

LM2902WYPT جائزہ

STMicroelectronics LM2902WYPT is a low-power, four-channel operational amplifier with internally compensated amplifiers, a 1.3 MHz gain-bandwidth product, 100 dB voltage gain, and 375 uA supply current per amplifier in a 14-TSSOP package. It operates from single supplies up to 30 V or dual supplies up to ±15 V, with input common-mode voltage ranges extending below the negative rail.

An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences, buffer sensors, drive loads, and implement feedback-control loops. The LM2902 belongs to the broader operational amplifier hierarchy, where four internally compensated amplifiers are integrated into one package to reduce component count in industrial, automotive, and instrumentation systems. Its push-pull output stage supports a variety of low- and mid-frequency signal-conditioning applications.

Key electrical characteristics include a 1.3 MHz gain-bandwidth product, 100 dB large-signal voltage gain, 375 uA supply current per amplifier, 20 nA low input bias current, and 2 nA low input-offset current. The 800 V ESD protection rating helps improve handling robustness, while the wide supply range supports circuits operating from industrial control, test, measurement, and vehicle-related power systems.

The LM2902 architecture provides four independent high-gain amplifiers with internal frequency compensation. This simplifies PCB layout because external compensation networks are not required. The common-mode input range includes the negative supply rail, making the device useful in single-supply sensor interfaces where signals remain close to ground. The wide input bias-voltage range also supports bipolar input stages within the device.

Typical uses include four-channel sensor amplification, low-frequency active filtering, transducer interfacing, current monitoring, sample-and-hold signal conditioning, and general-purpose analog control. The device can also provide independent amplifier sections for comparators, waveform conditioners, and audio or communications interface circuits when the bandwidth and slew-rate requirements remain modest.

For layout, place input and feedback components close to their associated amplifier pins and keep sensitive input traces away from high-current switching paths. Because the LM2902 is intended primarily for low-frequency precision-oriented applications, verify bandwidth, output swing, load capability, noise, and input-offset requirements against the actual signal path. Stable feedback design is essential because the amplifiers are internally compensated.

This product page combines the manufacturer device information with practical engineering guidance for single- and dual-supply implementation, application analysis, package considerations, and drop-in replacement evaluation. It is intended to help engineers select the LM2902WYPT for general-purpose four-amplifier designs and to identify what must be checked before PCB-level substitution.

کے لیے ڈراپ اِن متبادل LM2902WYPT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM2902WYPT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Gain-Bandwidth Product, Amplifier Type, Number of Amplifiers, Product Type.

Texas Instruments
Package: 14-pin TSSOP (PW), 4.40 mm width
Gain-Bandwidth Product: 1.2 MHz
Amplifier Type: General-purpose
موازنہ کریں LM2902WYPT →
STMicroelectronics
Package: 14-SOIC
Product Type: Quad Operational Amplifier
موازنہ کریں LM2902WYPT →
STMicroelectronics
Amplifier Type: Low-power general-purpose operational amplifier
Number of Amplifiers: 4 circuits
موازنہ کریں LM2902WYPT →

LM2902YPT

✅ ڈراپ-اِن
STMicroelectronics
📦 14-TSSOP
4 circuits · Low-power general-purpose operational amplifier · Yes · 20 nA · 1.3 MHz · 0.4 V/µs · 7 mV · Push-pull

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM2902PWRG3

✅ ڈراپ-اِن
Texas Instruments
📦 14-TSSOP
4 amplifiers · General-purpose · 26 V · 1.2 MHz · 2 mV · 0.5 V/µs · 0.8 mA typical · Single supply or split supply

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM2902WYPT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Amplifier Count 4 amplifiers
Product Type Low-power quad operational amplifier
Gain-Bandwidth Product 1.3 MHz
Large-Signal Voltage Gain 100 dB
Supply Current per Amplifier 375 uA
Input Bias Current 20 nA
Input Offset Current 2 nA
ESD Protection 800 V
Single-Supply Operating Range Up to 30 V
Dual-Supply Operating Range Up to ±15 V
Input Common-Mode Voltage Range Includes the negative supply rail
Frequency Compensation Internal
Output Stage Push-pull
پیکیج 14-TSSOP
Package Width 4.40 mm
ماؤنٹنگ ٹائپ Surface mount

LM2902WYPT 4.40 mm پن کنفیگریشن گائیڈ

LM2902WYPT (4.40 mm پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

LM2902WYPT کے لیے 4.40 mm پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM2902WYPT.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

LM2902WYPT کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, Automotive Control Circuit Amplification, Active Low-Frequency Filters, Current Monitoring and Control Loops, Test and Measurement Buffering, Audio and Communications Interface Circuits.

🏭

Industrial Sensor Signal Conditioning

The LM2902WYPT fits four-channel industrial sensor interfaces because it combines four independent amplifiers with an input common-mode range that includes the negative supply rail. This helps process signals from pressure, temperature, and position sensors that operate near ground. With a 1.3 MHz gain-bandwidth product and 375 uA supply current per amplifier, it provides useful bandwidth without imposing a high power budget. Use each section for gain, buffering, or active filtering, and verify input offset, output swing, noise, and operating-temperature requirements against the sensor interface.

🚗

Automotive Control Circuit Amplification

The LM2902WYPT is suitable for automotive and industrial control circuits that need several low-frequency analog channels in one package. The STMicroelectronics device provides four internally compensated high-gain amplifiers, a 1.3 MHz gain-bandwidth product, and operation across single supplies up to 30 V. That combination supports conditioning of resistive, inductive, and voltage-based sensor signals while reducing board area. The circuit must remain within the verified supply and common-mode limits, and the automotive qualification status should be confirmed for each production order code.

🔧

Active Low-Frequency Filters

The LM2902WYPT can implement several active-filter stages because it contains four independent, internally compensated amplifiers with a 1.3 MHz gain-bandwidth product. SECTIONS can form low-pass, high-pass, band-pass, or notch networks when component tolerances and closed-loop gain are selected carefully. The 375 uA supply current per amplifier is useful in compact multi-filter modules, while the push-pull output stage supports standard feedback configurations. Confirm slew rate, output-current capability, and stability margins before selecting component values for the intended signal bandwidth.

⚡

Current Monitoring and Control Loops

The LM2902WYPT is appropriate for current-monitoring and slow feedback-control circuits that need several amplifier channels sharing one package. Its 100 dB large-signal voltage gain and 1.3 MHz gain-bandwidth product provide useful open-loop performance for gain-of-10 or lower analog stages, while internal frequency compensation avoids external compensation networks. The four channels can amplify a current-sense signal, condition a reference, compare a threshold, and buffer a control output. Verify the input offset current of 2 nA, output swing, and response time against the control-loop accuracy and stability requirements.

🖥️

Test and Measurement Buffering

The LM2902WYPT can provide active buffering, gain, and differential-to-single-ended stages in test and measurement equipment. Four independent channels reduce the number of amplifier packages needed when routing several low-frequency signals through a common analog section. Its 375 uA supply current per amplifier is suitable for compact portable or embedded test systems, and the negative-rail-inclusive common-mode input range supports circuits that reference ground. Before using it with high-accuracy or high-impedance probes, verify input bias current, offset voltage, input capacitance, and output settling requirements.

🎧

Audio and Communications Interface Circuits

The LM2902WYPT can handle low-frequency audio and communications interface functions such as input buffering, active gain, impedance conversion, and channel mixing. Its 1.3 MHz gain-bandwidth product covers many voice-band and control-signal tasks, while the push-pull output stage supports common feedback networks. Four channels allow a compact implementation of a two-channel audio preamplifier plus auxiliary buffering or filtering functions. Audio designs should also check noise, output swing, slew rate, channel matching, and the system load, because bandwidth alone does not determine full signal quality.

What is the LM2902WYPT?
The LM2902WYPT is a four-channel, low-power operational amplifier from STMicroelectronics. According to the manufacturer product page, it contains four independent, internally frequency-compensated, high-gain amplifiers and is intended for automotive and industrial control systems. The device provides a 1.3 MHz gain-bandwidth product, 100 dB voltage gain, and operates from a single supply up to 30 V or dual supplies up to ±15 V.
What are the key specifications of LM2902WYPT that engineers should know?
The LM2902WYPT combines four internally compensated amplifiers in a 14-TSSOP package. According to the STMicroelectronics LM2902W documentation, key specifications include a 1.3 MHz gain-bandwidth product, 100 dB large-signal voltage gain, 375 uA supply current per amplifier, 20 nA input bias current, and 2 nA input-offset current. Its input common-mode range includes the negative supply rail.
Can LM2902WYPT operate from a single 5 V supply?
Yes, the LM2902WYPT can operate from a single supply within its stated supply range, including a 5 V system. According to the STMicroelectronics product page, the device supports single-supply operation up to 30 V, and its input common-mode range includes the negative supply rail. The negative-rail capability is especially useful for sensors whose output remains near ground.
Where can I download the LM2902WYPT datasheet PDF?
The official LM2902W product page on the STMicroelectronics website provides the manufacturer datasheet and supporting technical information for the LM2902WYPT configuration. Use the STMicroelectronics LM2902W product page at st.com as the primary document source. The distributor-hosted PDF mirrors can also help access the 20-page LM2902 document without relying on unofficial summaries.
Where can I find the LM2902WYPT pinout?
The LM2902WYPT pinout is shown in the pin-description section of the STMicroelectronics LM2902W manufacturer datasheet. The device is supplied in a 14-TSSOP package with four independent operational amplifiers. Use the manufacturer pin table when assigning inputs, outputs, supply rails, and ground connections, because exposed-pad or thermal details should not be inferred from a generic LM2902 drawing.
What can replace the LM2902WYPT?
A replacement must use the same 14-TSSOP footprint, preserve the four-amplifier pin assignment, and meet the supply-voltage, bandwidth, input-offset, and output-stage requirements of the original circuit. The LM2902YPT is a closely related STMicroelectronics ordering configuration, while LM2902PW is a cross-brand option identified in the LM2902 comparison results. Confirm the complete manufacturer pinout and electrical limits before substitution.
Is the LM2902WYPT the same as the LM2902WDT?
No. The LM2902WYPT and LM2902WDT share the LM2902W device family and four-amplifier architecture, but their orderable packages differ. LM2902WYPT is specified in a 14-TSSOP package, whereas LM2902WDT is not the same mechanical package. A PCB-level substitution therefore requires checking the footprint and pin arrangement rather than relying only on the base device name.
LM2902WYPT vs LM2902YPT - which is better for an existing design?
Choose the ordering configuration that matches the PCB footprint and required temperature grade rather than selecting by the nearest family name. The LM2902WYPT and LM2902YPT are both associated with STMicroelectronics TSSOP ordering variants, but their suffix codes can encode different ordering or temperature information. Review the manufacturer ordering table and compare the marked part number before committing either variant to production.
When should I choose LM2902WYPT over another quad op amp?
Choose the LM2902WYPT when the design needs four independent, internally compensated amplifiers, a 14-TSSOP footprint, low power consumption, and operation from a wide single- or dual-supply range. Its 1.3 MHz bandwidth is appropriate for general-purpose low-frequency signal conditioning, but it may not suit precision, high-speed, low-offset, or rail-to-rail applications that require more specialized amplifier characteristics.
Is LM2902WYPT suitable for industrial sensor interfaces?
Yes, the LM2902WYPT is suitable for many industrial and automotive signal-conditioning applications because it was designed for those control-system environments. The negative-rail-inclusive input range helps interface sensors operating near ground, and the four independent channels can reduce the number of amplifier packages. The design must still verify temperature limits, input offset, output swing, noise, and stability.
Does the LM2902WYPT need external frequency compensation?
No, each LM2902WYPT amplifier has internal frequency compensation. According to the STMicroelectronics product description, the four high-gain operational amplifiers are internally frequency-compensated. This simplifies board layout and reduces component count, but stable operation still depends on correct feedback-network design and suitable output loading within the electrical limits.
What power supply voltage can LM2902WYPT use?
The LM2902WYPT supports single-supply operation over a range extending to 30 V and dual-supply operation extending to ±15 V. According to the STMicroelectronics LM2902W manufacturer documentation, the common-mode input range includes the negative supply rail. Actual operating points must remain within the device limits, and input and output voltages must not exceed the permitted supply and common-mode boundaries.
Where can I buy LM2902WYPT and check stock?
Use the Request a Quote form on this page to ask about LM2902WYPT availability, current lead time, and order quantities. The form connects the request directly with XAIPART without relying on a static stock count. Include your required delivery date, approved quantity, and whether the 14-TSSOP packaging format is acceptable for your assembly process.
What is the price of LM2902WYPT?
The current commercial terms for LM2902WYPT are handled through the Request a Quote form on this page. Submit the required quantity, target delivery date, and packaging needs to obtain a current quotation and availability confirmation. This approach also allows XAIPART to account for project quantities and supply conditions without embedding a potentially stale price in technical content.
What is the lead time for LM2902WYPT?
Submit an LM2902WYPT inquiry through the Request a Quote form on this page to confirm current lead time and stock status. Lead time can vary with order quantity and market conditions, so procurement should obtain a written schedule tied to its production plan. Include the required delivery date and number of production assemblies when requesting that confirmation.
Is LM2902WYPT RoHS and REACH compliant?
The manufacturer product page and the device datasheet should be checked for the exact environmental and material declarations associated with LM2902WYPT. Do not infer a compliance status solely from the family name or package format. Request the current declaration from XAIPART when certification documentation is required for procurement, qualification, or customer-specific environmental reporting.

کے لیے انجینئرنگ ریفرنس ڈیٹا LM2902WYPT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the LM2902WYPT when a design needs four independent, internally compensated general-purpose amplifiers in a 14-TSSOP package. It is particularly suitable for low-frequency industrial, automotive, sensor, filtering, and control applications that benefit from an input common-mode range extending to the negative rail. The 1.3 MHz gain-bandwidth product and 375 uA per-amplifier supply current provide a practical balance for compact, low-power analog sections. Consider LM2902YPT when its specific ordering code offers the preferred temperature grade or commercial configuration within the same TSSOP footprint. Consider LM2902PW only after checking its complete electrical limits, especially offset voltage, bandwidth, supply current, output swing, and common-mode range against the original design. Choose a precision or rail-to-rail amplifier instead when low offset, low noise, fast settling, or operation close to the positive supply rail is essential.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ LM2902YPT LM2902PW
Brand STMicroelectronics STMicroelectronics Texas Instruments
Package 14-TSSOP 14-TSSOP 14-TSSOP
Amplifier Count 4 amplifiers 4 amplifiers 4 amplifiers

اہم امتیازی خصوصیات

  • Four integrated amplifier channels with internal compensation (بمقابلہLM2902PW)
  • Wide single- and dual-supply operating capability (بمقابلہLM2902YPT)
  • Ground-referenced input capability (بمقابلہLM2902PW)

ڈیزائن نوٹس

Place each amplifier's input, feedback, and decoupling connections close to the associated TSSOP pins. Keep high-impedance input traces short, avoid routing them beneath digital or switching-current paths, and use a continuous ground plane. The LM2902 has four independent amplifier sections, so assign and route each channel consistently to prevent feedback from one signal path from coupling into another.

Do not assume that every LM2902 package variant is a mechanical replacement. The target uses a 14-TSSOP package, while other ordering codes in the family can use different lead styles or temperature options. Compare the manufacturer pin table, footprint dimensions, exposed-pad requirements, and ordering information before replacing a populated board. For new layouts, verify input offset, common-mode limits, output swing, and load drive under the actual supply voltage.

Decouple the supply pins locally with ceramic capacitance selected using the stability and transient-response requirements in the manufacturer datasheet. Estimated: four amplifiers operating at 375 uA each draw approximately 1.5 mA total, excluding the load currents driven through the output stages. This arithmetic estimate does not include input bias current, output-current demand, or supply ripple, so verify the regulator and capacitor design against the complete loaded circuit.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The device is designed for automotive and industrial control applications, but the exact orderable MPN's environmental declarations and AEC-Q100 qualification status were not stated. Request current compliance documentation when required.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-17 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

LM2902WYPT datasheet LM2902WYPT datasheet pdf LM2902WYPT pinout LM2902WYPT specifications LM2902WYPT equivalent LM2902WYPT replacement LM2902WYPT vs LM2902YPT LM2902WYPT vs LM2902PW LM2902WYPT price LM2902WYPT stock STMicroelectronics LM2902WYPT LM2902WYPT 14-TSSOP pinout LM2902WYPT 1.3MHz quad op amp LM2902WYPT application circuit LM2902WYPT lead time

متعلقہ اجزاء اور اصطلاحات

STMicroelectronics LM2902WYPT LM2902W LM2902YPT LM2902PW Texas Instruments operational amplifier op amp quad operational amplifier analog amplifier signal-conditioning IC integrated circuit semiconductor internal frequency compensation push-pull output stage 1.3 MHz gain-bandwidth product 100 dB voltage gain 375 uA supply current per amplifier negative-rail-inclusive common-mode range 14-TSSOP package TSSOP package family surface-mount technology industrial control systems automotive electronics sensor signal conditioning
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں