LM393BIDDFR - Dual Open-Collector Comparator | Texas Instruments
MPN: LM393BIDDFR ✓ فعالLM393BIDDFR جائزہ
A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the non-inverting input exceeds the inverting input, or vice versa. The LM393B belongs to the voltage-comparator hierarchy, where differential analog signals are converted into logic-level decisions for control, protection, or system supervision.
The B-version LM393B improves on the original LM393 family with lower offset voltage, lower supply current, lower input bias current, faster response time, and stronger input protection. Key improvements include a maximum rating of 38 V, a 2 kV human-body-model ESD rating, and a response time of 1 us. These characteristics make the device suitable for cost-sensitive industrial and commercial designs that require accurate threshold detection.
Each internal comparator has a differential input stage, a logic output stage, and an open-collector transistor output. The open-collector outputs can sink current while remaining electrically isolated from the output supply, allowing a pull-up resistor to establish the logic-high voltage. The two channels share supply pins but otherwise operate independently, making channel-to-channel coupling minimal in normal use.
Typical applications include overvoltage and undervoltage monitoring, temperature-setpoint control, battery-cell protection, zero-cross detection, sensor signal conditioning, and industrial control interfaces. The wide supply range also supports 12 V and 24 V industrial systems, while the low input bias current benefits high-impedance sensor nodes.
Designers should use a pull-up resistor on each open-collector output and account for the output's inverted logic. Place bypass capacitors close to the supply pins, verify the input common-mode range at every operating condition, and avoid forcing an output below its externally imposed logic-high level. Confirm timing requirements against the 1 us response-time specification when the comparator drives slow logic or long capacitive loads.
کے لیے ڈراپ اِن متبادل LM393BIDDFR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM393BIDDFR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںLM393BIDDFR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 independent channels |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| سپلائی کرنٹ | 200 uA per comparator |
| Propagation Delay | 1 us |
| ESD Rating, Human Body Model | 2 kV |
| آؤٹ پٹ کی قسم | Open collector |
| Common-Mode Input | Rail-to-rail |
| Grade | Commercial grade |
| آپریٹنگ درجہ حرارت رینج | -40 C to +85 C |
| پیکیج | SOT-23-THN (DDF), 8 pins |
| Package Dimensions | 2 x 2 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
LM393BIDDFR 2 x 2 mm پن کنفیگریشن گائیڈ
LM393BIDDFR (2 x 2 mm پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM393BIDDFR.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
LM393BIDDFR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Overvoltage Monitoring, Battery Pack Protection Monitoring, Temperature Sensor Threshold Control, Zero-Cross and Phase Detection, Sensor Signal Conditioning, Power-Sequence and Fault Control.
Industrial Overvoltage Monitoring
The LM393BIDDFR fits 24 V industrial overvoltage supervision because its maximum supply rating is 38 V and its input common-mode range reaches the supply rails. Connect one input to a precision divider and the other to a reference voltage, then use the open-collector output to inhibit a downstream converter or signal a controller. The 0.37 mV low-offset target supports closer threshold accuracy, while the 2 kV HBM ESD rating improves robustness around exposed industrial connector inputs. Provide an output pull-up and verify transient levels against the absolute maximum rating.
تجویز کردہ
Battery Pack Protection Monitoring
The LM393BIDDFR can supervise individual battery cells in a multi-cell pack by comparing a divided cell voltage against a reference. Its rail-to-rail input behavior allows sensing near the positive rail, and the open-collector output can pull down a shared fault line so that any comparator can report an overvoltage condition. The 38 V maximum supply rating supports stacked-cell systems, although the actual application must remain below the operating voltage specified for the design. Use the manufacturer input-range and supply-current tables before adding a high-impedance reference network.
تجویز کردہ
Temperature Sensor Threshold Control
The LM393BIDDFR converts a temperature-sensor signal into a hardware switching decision with two independent comparison channels. One channel can detect an upper temperature limit while the other handles a lower limit, allowing independent fan, heater, or shutdown commands from one package. Its 1 us response time handles ordinary thermal-control loops, and the low 3.5 nA input bias current minimizes loading on resistive sensor dividers. Because the outputs are open collector, pull-ups to the control-system logic supply allow the outputs to remain compatible with a different logic voltage.
تجویز کردہ
Zero-Cross and Phase Detection
The LM393BIDDFR is appropriate for detecting a signal crossing a reference near an analog system's zero point. A divided input is compared with the other input, and the open-collector transition provides a digital event to a controller, timer, or thyristor-drive circuit. The 1 us response time is adequate for power-frequency zero-cross and general control applications, while rail-to-rail inputs help define the useful sensing range. Keep the comparator input network short and away from switching nodes to prevent false triggering.
تجویز کردہ
Sensor Signal Conditioning
The LM393BIDDFR converts a slowly varying analog sensor output into a clean threshold event for downstream digital control. Its 0.37 mV low input offset and 3.5 nA input bias current are advantageous when the sensing node has a high source impedance and a small signal change must remain detectable. The two independent channels can handle two sensor thresholds or provide complementary decisions. Add input filtering, maintain a defined common-mode range, and select the pull-up resistor to balance noise immunity against output-edge speed.
تجویز کردہ
Power-Sequence and Fault Control
The LM393BIDDFR can supervise multiple rails by comparing divided rail voltages with reference levels and combining the open-collector outputs into a system fault indication. The wide 38 V maximum supply capability suits 12 V and 24 V rails, while the two-channel architecture minimizes package count in compact control boards. Because an open-collector output can be tied with other outputs for wired-OR fault signaling, separate pull-up values may be used to distinguish normal state from fault state. Verify input levels and timing margin against the system power-up profile.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM393BIDDFR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Package | SOT-23-THN (DDF), 8 pins |
| Brand | Texas Instruments |
| Comparator Configuration | Dual differential comparator |
| Number of Channels | 2 |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Supply Current | 200 uA per comparator |
| Propagation Delay | 1 us |
| Output Type | Open collector |
| Common-Mode Input | Rail-to-rail |
| ESD Rating, Human Body Model | 2 kV |
| Operating Temperature Range | -40 C to +85 C |
ڈیزائن نوٹس
Each open-collector output requires a pull-up resistor; without one, the output cannot reach a valid logic-high state. Do not connect the output directly to a supply rail unless the sink-current rating allows it. Also avoid driving an output externally above its intended logic-high level, and remember that the LM393B comparator output is inverted relative to the usual non-inverting-input logic.
Place the input-divider and reference components close to the comparator pins, and route the two differential inputs as a matched pair to reduce pickup from adjacent switching circuits. Keep the pull-up resistor near the output pin so the open-collector node has a short high-impedance trace. For exposed-pad package variants, follow the manufacturer's land pattern and thermal-via recommendation.
The 1 us response-time specification leaves limited margin for high-speed requirements, so add hysteresis around the threshold when noise or slow input transitions could cause repeated output chatter. Positive feedback through a resistor from output to the non-inverting input creates hysteresis, but the feedback must not exceed the output-stage voltage limits. Validate the final threshold with worst-case temperature and supply tolerance.
Estimated: each comparator contributes approximately 200 uA of supply current at the device level, so two channels require about 400 uA before load and bias-current effects. Total device dissipation is also influenced by the output pull-up network during output-low states. Confirm the maximum input voltage in the industrial design, allowing transient margin below the 38 V maximum rating.
تعمیل کی معلومات
The device is identified as a commercial-grade dual comparator. No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is shown in the product information used for this page.