Texas Instruments

LM393BIDDFR - Dual Open-Collector Comparator | Texas Instruments

MPN: LM393BIDDFR ✓ Hoạt động
38 V Vdss 3.5 nA Id SOT-23-THN (DDF), 8 pins Package
MOQ: 1 |

LM393BIDDFR Tóm tắt

The Texas Instruments LM393BIDDFR is a dual differential comparator containing two independent comparison channels in an 8-pin SOT-23-THN package. It operates from a single positive supply up to 38 V and supports rail-to-rail input common-mode operation, with an open-collector output on each channel. Typical input offset voltage is as low as 0.37 mV, input bias current is 3.5 nA, and each comparator draws approximately 200 uA of supply current.

A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the non-inverting input exceeds the inverting input, or vice versa. The LM393B belongs to the voltage-comparator hierarchy, where differential analog signals are converted into logic-level decisions for control, protection, or system supervision.

The B-version LM393B improves on the original LM393 family with lower offset voltage, lower supply current, lower input bias current, faster response time, and stronger input protection. Key improvements include a maximum rating of 38 V, a 2 kV human-body-model ESD rating, and a response time of 1 us. These characteristics make the device suitable for cost-sensitive industrial and commercial designs that require accurate threshold detection.

Each internal comparator has a differential input stage, a logic output stage, and an open-collector transistor output. The open-collector outputs can sink current while remaining electrically isolated from the output supply, allowing a pull-up resistor to establish the logic-high voltage. The two channels share supply pins but otherwise operate independently, making channel-to-channel coupling minimal in normal use.

Typical applications include overvoltage and undervoltage monitoring, temperature-setpoint control, battery-cell protection, zero-cross detection, sensor signal conditioning, and industrial control interfaces. The wide supply range also supports 12 V and 24 V industrial systems, while the low input bias current benefits high-impedance sensor nodes.

Designers should use a pull-up resistor on each open-collector output and account for the output's inverted logic. Place bypass capacitors close to the supply pins, verify the input common-mode range at every operating condition, and avoid forcing an output below its externally imposed logic-high level. Confirm timing requirements against the 1 us response-time specification when the comparator drives slow logic or long capacitive loads.

Bộ thay thế dễ dàng lắp đặt cho LM393BIDDFR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM393BIDDFR (cùng hình factor và footprint) — khác nhau ở Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.

Texas Instruments
Comparator Type: Dual standard general-purpose comparator
Grade: Industrial grade
Number of Channels: 2 channels
So sánh với LM393BIDDFR →

Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.

Yêu cầu các bộ thay thế

LM393BIDDFR Tỷ lệ tối đa & tính chất điện

Comparator Type Dual differential comparator
Number of Channels 2 independent channels
Maximum Supply Voltage 38 V
Input Offset Voltage 0.37 mV
Input Bias Current 3.5 nA
Điện áp cung cấp 200 uA per comparator
Propagation Delay 1 us
ESD Rating, Human Body Model 2 kV
Kiểu đầu ra Open collector
Common-Mode Input Rail-to-rail
Grade Commercial grade
Khoảng nhiệt độ hoạt động -40 C to +85 C
Hộp SOT-23-THN (DDF), 8 pins
Package Dimensions 2 x 2 mm
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân LM393BIDDFR 2 x 2 mm

Cấu hình chân cho LM393BIDDFR (2 x 2 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 2 x 2 mm cho LM393BIDDFR

Không có dữ liệu chân cụ thể sẵn có cho LM393BIDDFR.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

LM393BIDDFR phù hợp cho 6 Áp dụngs: Industrial Overvoltage Monitoring, Battery Pack Protection Monitoring, Temperature Sensor Threshold Control, Zero-Cross and Phase Detection, Sensor Signal Conditioning, Power-Sequence and Fault Control.

🏭

Industrial Overvoltage Monitoring

The LM393BIDDFR fits 24 V industrial overvoltage supervision because its maximum supply rating is 38 V and its input common-mode range reaches the supply rails. Connect one input to a precision divider and the other to a reference voltage, then use the open-collector output to inhibit a downstream converter or signal a controller. The 0.37 mV low-offset target supports closer threshold accuracy, while the 2 kV HBM ESD rating improves robustness around exposed industrial connector inputs. Provide an output pull-up and verify transient levels against the absolute maximum rating.

⚡

Battery Pack Protection Monitoring

The LM393BIDDFR can supervise individual battery cells in a multi-cell pack by comparing a divided cell voltage against a reference. Its rail-to-rail input behavior allows sensing near the positive rail, and the open-collector output can pull down a shared fault line so that any comparator can report an overvoltage condition. The 38 V maximum supply rating supports stacked-cell systems, although the actual application must remain below the operating voltage specified for the design. Use the manufacturer input-range and supply-current tables before adding a high-impedance reference network.

🌡️

Temperature Sensor Threshold Control

The LM393BIDDFR converts a temperature-sensor signal into a hardware switching decision with two independent comparison channels. One channel can detect an upper temperature limit while the other handles a lower limit, allowing independent fan, heater, or shutdown commands from one package. Its 1 us response time handles ordinary thermal-control loops, and the low 3.5 nA input bias current minimizes loading on resistive sensor dividers. Because the outputs are open collector, pull-ups to the control-system logic supply allow the outputs to remain compatible with a different logic voltage.

📐

Zero-Cross and Phase Detection

The LM393BIDDFR is appropriate for detecting a signal crossing a reference near an analog system's zero point. A divided input is compared with the other input, and the open-collector transition provides a digital event to a controller, timer, or thyristor-drive circuit. The 1 us response time is adequate for power-frequency zero-cross and general control applications, while rail-to-rail inputs help define the useful sensing range. Keep the comparator input network short and away from switching nodes to prevent false triggering.

🧩

Sensor Signal Conditioning

The LM393BIDDFR converts a slowly varying analog sensor output into a clean threshold event for downstream digital control. Its 0.37 mV low input offset and 3.5 nA input bias current are advantageous when the sensing node has a high source impedance and a small signal change must remain detectable. The two independent channels can handle two sensor thresholds or provide complementary decisions. Add input filtering, maintain a defined common-mode range, and select the pull-up resistor to balance noise immunity against output-edge speed.

🖥️

Power-Sequence and Fault Control

The LM393BIDDFR can supervise multiple rails by comparing divided rail voltages with reference levels and combining the open-collector outputs into a system fault indication. The wide 38 V maximum supply capability suits 12 V and 24 V rails, while the two-channel architecture minimizes package count in compact control boards. Because an open-collector output can be tied with other outputs for wired-OR fault signaling, separate pull-up values may be used to distinguish normal state from fault state. Verify input levels and timing margin against the system power-up profile.

Tóm tắt các sản phẩm được đề xuất

LM393B Comparator family reference Được sử dụng trong: Industrial Overvoltage Monitoring, Battery Pack Protection Monitoring, Temperature Sensor Threshold Control, Zero-Cross and Phase Detection, Sensor Signal Conditioning, Power-Sequence and Fault Control
What is the LM393BIDDFR and what are its main specifications?
The LM393BIDDFR is a Texas Instruments dual differential comparator with two independent open-collector channels in an 8-pin SOT-23-THN package. According to the manufacturer product information, it operates up to 38 V, offers 0.37 mV low input offset, 3.5 nA input bias current, 200 uA supply current per comparator, a 1 us response time, and a 2 kV HBM ESD rating. The two channels share supply connections but can perform separate comparison functions.
What is the supply voltage range of the LM393BIDDFR?
The LM393BIDDFR supports single-supply operation up to a maximum rating of 38 V, as stated on the Texas Instruments LM393B product page. Its input common-mode range extends to the supply rails for rail-to-rail sensing. The maximum rating is an absolute limit rather than a recommended operating condition, so the application should include transient margin when an industrial bus or supply rail can overshoot the nominal voltage.
Where can I download the LM393BIDDFR datasheet PDF?
The official LM393BIDDFR datasheet is available through the Texas Instruments LM393B part-details page at https://www.ti.com/product/LM393B/part-details/LM393BIDDFR. The page links the manufacturer datasheet and ordering information. Engineers should use the pin-configuration table, electrical characteristics, and application guidance in that document when assigning PCB tracks and calculating pull-up resistor values.
What is the LM393BIDDFR pinout?
The LM393BIDDFR is an 8-pin SOT-23-THN dual comparator with two independent differential input pairs and two open-collector outputs. Use the pin-description table in the manufacturer datasheet for the exact numbered assignments and exposed-pad treatment. Both channels require external pull-up resistors because the open-collector transistors sink output current rather than actively driving a high logic level.
Does the LM393BIDDFR need pull-up resistors?
Yes, each open-collector output on the LM393BIDDFR requires an external pull-up resistor to establish a logic-high voltage. The output transistor pulls the node toward ground when the comparison state is active, while the resistor returns the node to the selected logic-high supply when the transistor is off. Select the resistor to balance the required sink current, rise time, and the maximum current permitted by the output stage.
What can replace the LM393BIDDFR on the same PCB?
The closest direct replacement is a dual open-collector comparator with the same 8-pin SOT-23 footprint, matching channel count, input arrangement, output topology, and supply rating. A device with a different package, push-pull output, or narrower voltage range is not a drop-in substitution even if its comparator performance is similar. Use the Request a Quote form on this page to request an engineering review of currently available equivalents.
Is the LM393BIDDFR better than the original LM393?
The LM393BIDDFR is the improved B-version of the original LM393 family and provides lower offset voltage, lower bias current, lower supply current, faster response, and improved ESD robustness. Texas Instruments states that the LM393B family is a drop-in replacement for LM293, LM393, and LM2903 versions when package, grade, and operating requirements match. The improvement does not change the open-collector output concept.
When should I choose the LM393BIDDFR over a lower-voltage comparator?
Choose the LM393BIDDFR when the circuit operates from a relatively high supply, needs rail-to-rail input sensing, or must tolerate supply transients in a 12 V or 24 V industrial environment. A low-voltage comparator may be preferable in compact battery-powered systems where every milliamp matters, but its input and supply limits require more careful level translation and protection.
What is the LM393BIDDFR suitable for in a 24 V industrial control system?
The LM393BIDDFR is well suited to 24 V industrial monitoring because of its 38 V maximum supply rating, rail-to-rail input common-mode capability, and 2 kV HBM ESD protection. It can monitor a 24 V process line against an adjustable threshold and drive a PLC input or control relay-driver stage. Keep the output pull-up at a logic level accepted by the following device and add protection if the monitored line is exposed to severe transients.
How fast is the LM393BIDDFR comparator response?
The LM393BIDDFR has a response time of 1 us, according to the Texas Instruments LM393B product page. This propagation capability is suitable for general-purpose threshold control and monitoring rather than high-speed edge detection. Actual system delay also depends on the overdrive applied to the inputs, the output pull-up resistance, and the capacitance of the driven node.
Is the LM393BIDDFR active?
Texas Instruments lists the LM393BIDDFR as a current dual commercial-grade comparator orderable in the DDF 8-pin package. The LM393B family is shown with an operating temperature range of -40 C to +85 C for this orderable configuration. Request a Quote on this page to confirm allocation, current lead time, and the packaging quantity available for production planning.
Where can I buy the LM393BIDDFR online?
The LM393BIDDFR is available through authorized electronics channels and is listed by multiple distributors, but stock and commercial terms change frequently. Use the Request a Quote form on this page to request current availability, order quantities, lead time, and pricing for the Texas Instruments LM393BIDDFR in its DDF package. Provide your target quantity and production schedule so the quotation can be matched to your purchasing requirement.
What is the price of the LM393BIDDFR?
Pricing for the LM393BIDDFR depends on quantity, package configuration, inventory, and contract terms, so a fixed price should not be assumed. Submit a request through the Request a Quote form on this page with your required quantity and delivery schedule. The same form can confirm current lead time, minimum order quantity, and any scheduled production allocations.
How long is the lead time for the LM393BIDDFR?
The current lead time for the LM393BIDDFR should be confirmed against live inventory and factory allocation before a build schedule is committed. Use the Request a Quote form on this page and state the required quantity, target date, and approved manufacturer preference. For new production programs, include a safety stock plan because distributor stock does not necessarily reflect sustained factory output.
Is the LM393BIDDFR suitable for battery-powered sensor applications?
The LM393BIDDFR is better suited to higher-voltage and industrial monitoring than to ultra-low-power battery sensing because each comparator draws approximately 200 uA of supply current. It remains appropriate for a 12 V or 24 V powered sensor interface where a robust open-collector output and wide supply range matter more than microampere-level standby consumption. For coin-cell systems, select a comparator specifically optimized for low quiescent current.
How should I design the output pull-up for the LM393BIDDFR?
Choose the LM393BIDDFR output pull-up resistance so the output rise time meets the receiving circuit's timing requirement while keeping sink current within the output-stage limit. A lower resistance produces a faster rising edge and more sink current; a higher resistance reduces sink current but slows the edge and increases susceptibility to noise. Include the trace capacitance and input leakage of the connected logic device in the sizing calculation.

Dữ liệu tham khảo kỹ thuật cho LM393BIDDFR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the LM393BIDDFR when a cost-sensitive design needs two independent threshold comparisons, a wide single-supply range, and open-collector outputs in a compact 8-pin surface-mount package. It is especially suitable for 12 V and 24 V industrial monitoring because of the 38 V maximum rating and rail-to-rail input behavior. A push-pull comparator is preferable when the circuit needs a fast actively driven edge without an external pull-up. A micropower comparator is preferable for coin-cell or continuously battery-powered operation because the LM393BIDDFR draws approximately 200 uA per channel. For a drop-in substitution, the candidate must match the DDF footprint, channel count, differential input arrangement, open-collector output, and operating voltage. Use the Request a Quote form to request a review of available substitutes and current supply conditions.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Package SOT-23-THN (DDF), 8 pins
Brand Texas Instruments
Comparator Configuration Dual differential comparator
Number of Channels 2
Maximum Supply Voltage 38 V
Input Offset Voltage 0.37 mV
Input Bias Current 3.5 nA
Supply Current 200 uA per comparator
Propagation Delay 1 us
Output Type Open collector
Common-Mode Input Rail-to-rail
ESD Rating, Human Body Model 2 kV
Operating Temperature Range -40 C to +85 C

Ghi chú thiết kế

Each open-collector output requires a pull-up resistor; without one, the output cannot reach a valid logic-high state. Do not connect the output directly to a supply rail unless the sink-current rating allows it. Also avoid driving an output externally above its intended logic-high level, and remember that the LM393B comparator output is inverted relative to the usual non-inverting-input logic.

Place the input-divider and reference components close to the comparator pins, and route the two differential inputs as a matched pair to reduce pickup from adjacent switching circuits. Keep the pull-up resistor near the output pin so the open-collector node has a short high-impedance trace. For exposed-pad package variants, follow the manufacturer's land pattern and thermal-via recommendation.

The 1 us response-time specification leaves limited margin for high-speed requirements, so add hysteresis around the threshold when noise or slow input transitions could cause repeated output chatter. Positive feedback through a resistor from output to the non-inverting input creates hysteresis, but the feedback must not exceed the output-stage voltage limits. Validate the final threshold with worst-case temperature and supply tolerance.

Estimated: each comparator contributes approximately 200 uA of supply current at the device level, so two channels require about 400 uA before load and bias-current effects. Total device dissipation is also influenced by the output pull-up network during output-low states. Confirm the maximum input voltage in the industrial design, allowing transient margin below the 38 V maximum rating.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The device is identified as a commercial-grade dual comparator. No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is shown in the product information used for this page.

Tìm kiếm liên quan

LM393BIDDFR datasheet LM393BIDDFR pinout LM393BIDDFR datasheet pdf LM393BIDDFR equivalent LM393BIDDFR replacement LM393BIDDFR cross reference LM393BIDDFR price LM393BIDDFR stock Texas Instruments LM393BIDDFR LM393B SOT-23-8 comparator LM393BIDDFR 38V open collector LM393BIDDFR application circuit

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM393BIDDFR LM393B LM393 LM2903B LM293 dual differential comparator voltage comparator analog integrated circuit semiconductor open-collector output rail-to-rail input input offset voltage input bias current supply current propagation delay ESD protection SOT-23-THN DDF package surface mount industrial control overvoltage monitoring battery protection temperature control
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ