LM393BIDDFR - Dual Open-Collector Comparator | Texas Instruments
MPN: LM393BIDDFR ✓ 啟用中LM393BIDDFR 概覽
A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the non-inverting input exceeds the inverting input, or vice versa. The LM393B belongs to the voltage-comparator hierarchy, where differential analog signals are converted into logic-level decisions for control, protection, or system supervision.
The B-version LM393B improves on the original LM393 family with lower offset voltage, lower supply current, lower input bias current, faster response time, and stronger input protection. Key improvements include a maximum rating of 38 V, a 2 kV human-body-model ESD rating, and a response time of 1 us. These characteristics make the device suitable for cost-sensitive industrial and commercial designs that require accurate threshold detection.
Each internal comparator has a differential input stage, a logic output stage, and an open-collector transistor output. The open-collector outputs can sink current while remaining electrically isolated from the output supply, allowing a pull-up resistor to establish the logic-high voltage. The two channels share supply pins but otherwise operate independently, making channel-to-channel coupling minimal in normal use.
Typical applications include overvoltage and undervoltage monitoring, temperature-setpoint control, battery-cell protection, zero-cross detection, sensor signal conditioning, and industrial control interfaces. The wide supply range also supports 12 V and 24 V industrial systems, while the low input bias current benefits high-impedance sensor nodes.
Designers should use a pull-up resistor on each open-collector output and account for the output's inverted logic. Place bypass capacitors close to the supply pins, verify the input common-mode range at every operating condition, and avoid forcing an output below its externally imposed logic-high level. Confirm timing requirements against the 1 us response-time specification when the comparator drives slow logic or long capacitive loads.
直接替換替代品,適用於 LM393BIDDFR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM393BIDDFR (相同外形與佔位) — 差異在於 Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.
此產品無可直接替換的替代品。
申請替代品LM393BIDDFR 最大額定值與電氣特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 independent channels |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| 供應電流 | 200 uA per comparator |
| Propagation Delay | 1 us |
| ESD Rating, Human Body Model | 2 kV |
| 輸出類型 | Open collector |
| Common-Mode Input | Rail-to-rail |
| Grade | Commercial grade |
| 工作溫度範圍 | -40 C to +85 C |
| 封裝 | SOT-23-THN (DDF), 8 pins |
| Package Dimensions | 2 x 2 mm |
| 安裝類型 | Surface mount |
LM393BIDDFR 2 x 2 mm 腳位配置指南
LM393BIDDFR(2 x 2 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM393BIDDFR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM393BIDDFR 適用於 6 應用s: Industrial Overvoltage Monitoring, Battery Pack Protection Monitoring, Temperature Sensor Threshold Control, Zero-Cross and Phase Detection, Sensor Signal Conditioning, Power-Sequence and Fault Control.
Industrial Overvoltage Monitoring
The LM393BIDDFR fits 24 V industrial overvoltage supervision because its maximum supply rating is 38 V and its input common-mode range reaches the supply rails. Connect one input to a precision divider and the other to a reference voltage, then use the open-collector output to inhibit a downstream converter or signal a controller. The 0.37 mV low-offset target supports closer threshold accuracy, while the 2 kV HBM ESD rating improves robustness around exposed industrial connector inputs. Provide an output pull-up and verify transient levels against the absolute maximum rating.
推薦
Battery Pack Protection Monitoring
The LM393BIDDFR can supervise individual battery cells in a multi-cell pack by comparing a divided cell voltage against a reference. Its rail-to-rail input behavior allows sensing near the positive rail, and the open-collector output can pull down a shared fault line so that any comparator can report an overvoltage condition. The 38 V maximum supply rating supports stacked-cell systems, although the actual application must remain below the operating voltage specified for the design. Use the manufacturer input-range and supply-current tables before adding a high-impedance reference network.
推薦
Temperature Sensor Threshold Control
The LM393BIDDFR converts a temperature-sensor signal into a hardware switching decision with two independent comparison channels. One channel can detect an upper temperature limit while the other handles a lower limit, allowing independent fan, heater, or shutdown commands from one package. Its 1 us response time handles ordinary thermal-control loops, and the low 3.5 nA input bias current minimizes loading on resistive sensor dividers. Because the outputs are open collector, pull-ups to the control-system logic supply allow the outputs to remain compatible with a different logic voltage.
推薦
Zero-Cross and Phase Detection
The LM393BIDDFR is appropriate for detecting a signal crossing a reference near an analog system's zero point. A divided input is compared with the other input, and the open-collector transition provides a digital event to a controller, timer, or thyristor-drive circuit. The 1 us response time is adequate for power-frequency zero-cross and general control applications, while rail-to-rail inputs help define the useful sensing range. Keep the comparator input network short and away from switching nodes to prevent false triggering.
推薦
Sensor Signal Conditioning
The LM393BIDDFR converts a slowly varying analog sensor output into a clean threshold event for downstream digital control. Its 0.37 mV low input offset and 3.5 nA input bias current are advantageous when the sensing node has a high source impedance and a small signal change must remain detectable. The two independent channels can handle two sensor thresholds or provide complementary decisions. Add input filtering, maintain a defined common-mode range, and select the pull-up resistor to balance noise immunity against output-edge speed.
推薦
Power-Sequence and Fault Control
The LM393BIDDFR can supervise multiple rails by comparing divided rail voltages with reference levels and combining the open-collector outputs into a system fault indication. The wide 38 V maximum supply capability suits 12 V and 24 V rails, while the two-channel architecture minimizes package count in compact control boards. Because an open-collector output can be tied with other outputs for wired-OR fault signaling, separate pull-up values may be used to distinguish normal state from fault state. Verify input levels and timing margin against the system power-up profile.
推薦
推薦產品摘要
工程參考資料,適用於 LM393BIDDFR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | SOT-23-THN (DDF), 8 pins |
| Brand | Texas Instruments |
| Comparator Configuration | Dual differential comparator |
| Number of Channels | 2 |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Supply Current | 200 uA per comparator |
| Propagation Delay | 1 us |
| Output Type | Open collector |
| Common-Mode Input | Rail-to-rail |
| ESD Rating, Human Body Model | 2 kV |
| Operating Temperature Range | -40 C to +85 C |
設計說明
Each open-collector output requires a pull-up resistor; without one, the output cannot reach a valid logic-high state. Do not connect the output directly to a supply rail unless the sink-current rating allows it. Also avoid driving an output externally above its intended logic-high level, and remember that the LM393B comparator output is inverted relative to the usual non-inverting-input logic.
Place the input-divider and reference components close to the comparator pins, and route the two differential inputs as a matched pair to reduce pickup from adjacent switching circuits. Keep the pull-up resistor near the output pin so the open-collector node has a short high-impedance trace. For exposed-pad package variants, follow the manufacturer's land pattern and thermal-via recommendation.
The 1 us response-time specification leaves limited margin for high-speed requirements, so add hysteresis around the threshold when noise or slow input transitions could cause repeated output chatter. Positive feedback through a resistor from output to the non-inverting input creates hysteresis, but the feedback must not exceed the output-stage voltage limits. Validate the final threshold with worst-case temperature and supply tolerance.
Estimated: each comparator contributes approximately 200 uA of supply current at the device level, so two channels require about 400 uA before load and bias-current effects. Total device dissipation is also influenced by the output pull-up network during output-low states. Confirm the maximum input voltage in the industrial design, allowing transient margin below the 38 V maximum rating.
合規資訊
The device is identified as a commercial-grade dual comparator. No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is shown in the product information used for this page.