Analog Devices

MAX232MWE/PR - Dual RS-232 Transceiver | Analog Devices

MPN: MAX232MWE/PR ✓ فعال
5 V Vdss 16-pin SOIC Package
MOQ: 1 |

MAX232MWE/PR جائزہ

Analog Devices MAX232MWE/PR is a dual RS-232 line transceiver with two transmitters and two receivers, a 5 V supply requirement, and a 16-pin SOIC package. It converts logic-level UART signals to RS-232 levels and converts received RS-232 signals back to logic levels. The MWE/PR configuration is identified as military temperature grade and uses a gull-wing SOP package with 16 terminals.

An RS-232 transceiver is an interface IC within the broader line-driver and line-receiver category. Its transmitter side adds the voltage swing and biasing required for RS-232 communication, while its receiver side detects the bipolar voltage levels presented on the cable. A complete dual transceiver is therefore useful where two serial data paths must be supported without using separate single-channel driver and receiver devices.

The MAX232MWE/PR provides two full RS-232 channels, operating from a 5 V supply and intended for multipoint or point-to-point RS-232 links. Its military-grade temperature designation makes it relevant to equipment that must tolerate extended environmental conditions. The 16-pin SOIC package supports conventional surface-mount PCB assembly, while its terminal finish is matte tin with an annealed finish and an e3 terminal classification.

Its interface architecture provides the required charge-pump and level-shifting functions for bidirectional RS-232 communication. The two transmitters are intended to drive external RS-232 lines, and the two receivers recover data from those lines for the host UART. Engineers should account for external line protection, connector pin assignment, and the power-supply bypass capacitors specified by the manufacturer datasheet when implementing the interface.

Typical applications include industrial serial controllers, legacy data-acquisition equipment, embedded service ports, telecom equipment, and RS-232 links between a microcontroller or host UART and an external connector. The same electrical interface can support control, monitoring, configuration, and diagnostic channels when the system already uses RS-232 and does not require a modern differential bus such as RS-485 or LVDS.

The main design tradeoff is that this device preserves compatibility with established RS-232 equipment rather than offering the longer reach, common-mode tolerance, and multi-drop capability associated with differential interfaces. Keep the MAX232 supply and ground connections compact, route the cable-side receive nodes away from fast digital signals, and place protection components where the external cable enters the assembly.

This page organizes the MAX232MWE/PR interface specifications, package characteristics, verified drop-in alternatives, comparison parameters, and practical PCB guidance. It also identifies commercial information through the page quotation workflow so engineers can evaluate availability without relying on static market pricing.

کے لیے ڈراپ اِن متبادل MAX232MWE/PR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX232MWE/PR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Interface Standard, Product Type, Package, Supply Voltage, Logic Compatibility.

Maxim Integrated
Interface Standard: EIA/TIA-232E and V.28/V.24
Product Type: RS-232 line-driver and receiver transceiver
Supply Voltage: +5 V
Analog Devices
Supply Voltage: +5 V
Logic Compatibility: TTL/CMOS logic interface
Analog Devices
Interface Standard: RS-232; EIA/TIA-232E and V.28/V.24 family application
Product Type: RS-232 line driver/receiver transceiver
Package: 16-pin wide SOIC
Maxim Integrated
Interface Standard: EIA/TIA-232E
Product Type: RS-232 transceiver interface IC
Package: 16-pin wide SOIC

MAX232CWE+

✅ ڈراپ-اِن
Analog Devices
📦 16-SOIC
RS-232 line driver/receiver transceiver · 4.5 V to 5.5 V · 2 · 2 · RS-232; EIA/TIA-232E and V.28/V.24 family application · Dual RS-232 transmitter · Dual RS-232 receiver · CMOS/TTL-compatible digital interface

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX232EWE+T

✅ ڈراپ-اِن
Maxim Integrated
📦 16-SOIC
RS-232 transceiver interface IC · 2 drivers · 2 receivers · 4.5 V to 5.5 V · 120 kbps · EIA/TIA-232E · CCITT V.28 and V.24 · +5 V

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX232ACWE+

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Maxim Integrated
📦 16-SOIC
RS-232 line-driver and receiver transceiver · 2 transmitters / 2 receivers · +5 V · EIA/TIA-232E and V.28/V.24 · 16-pin SOIC · Surface mount

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX232AEWE+

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Analog Devices
📦 16-SOIC
2 drivers · 2 receivers · 2/2 full-duplex · RS-232 · +5 V · 200 kb/s · 16-pin SOIC · 7.50 mm

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX232MWE/PR+

✅ ڈراپ-اِن
📦 16-SOIC
Same MAX232MWE military configuration and 16-SOIC package; the ordering suffix differs by one character with no channel-count change

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MAX232MWE/PR تفصیلات

Product Type Dual RS-232 transceiver
Number of Transmitters 2
Number of Receivers 2
Interface Standard RS-232
سپلائی وولٹیج 5 V
Supply Voltage Range 4.5 V to 5.5 V
پیکیج 16-pin SOIC
Terminal Count 16
Terminal Form Gull wing
Temperature Grade Military
Terminal Finish Matte tin (Sn), annealed
JESD-609 Code e3
Moisture Sensitivity Level MSL 1
Peak Reflow Temperature 260 C
Maximum Time at Peak Reflow 30 s
ماؤنٹنگ اسٹائل Surface mount

MAX232MWE/PR 16-pin soic پن کنفیگریشن گائیڈ

MAX232MWE/PR (16-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

MAX232MWE/PR کے لیے 16-pin soic پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX232MWE/PR.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

MAX232MWE/PR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Controller, Data-Acquisition Equipment, Embedded Diagnostic Port, Telecom Equipment Interface, Legacy Peripheral Adapter, Aerospace Support Electronics.

🏭

Industrial Serial Controller

The MAX232MWE/PR fits an industrial controller that must retain compatibility with RS-232 service equipment. Its two transmitters and two receivers provide two bidirectional RS-232 paths from a 5 V logic system, while the military temperature designation supports designs with wider environmental requirements. The device is used between the host UART and the external DB9 or equivalent connector, with the logic-side and cable-side nets kept separate by the manufacturer pinout. Because RS-232 is a single-ended, unbalanced interface, cable protection and grounding deserve attention in long or electrically noisy installations.

📊

Data-Acquisition Equipment

The MAX232MWE/PR is appropriate for legacy data-acquisition systems that transfer commands and measurements over RS-232. Two complete transceiver channels can support a primary data channel and a separate status or control channel from the same 4.5 V to 5.5 V supply domain. It is placed between the acquisition controller and the external serial connector, where its integrated transmitters and receivers replace separate line-driver and receiver packages. The main design consideration is to follow the specified charge-pump capacitor connections and place connector-side protection close to the cable entry.

🛠️

Embedded Diagnostic Port

A MAX232MWE/PR-based diagnostic port allows an embedded controller to communicate with service equipment, test fixtures, or a configuration terminal using established RS-232 equipment. The 16-SOIC package is convenient for compact industrial and aerospace-support electronics, while its two transmitters and two receivers permit bidirectional command traffic. Connect the UART logic signals to the receiver inputs and driver outputs as specified, then keep the RS-232 connector nets away from clocks and switching nodes. External protection should be selected for the cable voltage and grounding environment.

🌐

Telecom Equipment Interface

The MAX232MWE/PR can provide legacy RS-232 connectivity in telecom equipment that must interoperate with established test or network-management systems. Its dual-channel architecture reduces the component count compared with separate single-direction interface devices, and the 5 V supply operation fits systems that already include that rail. The military-grade designation is relevant where the equipment specifies elevated environmental requirements. Designers should still treat RS-232 as a point-to-point interface and use the manufacturer application circuit for supply bypass and charge-pump components.

🔌

Legacy Peripheral Adapter

The MAX232MWE/PR is useful in an adapter that lets a modern controller communicate with a legacy RS-232 printer, instrument, or service device. The adapter can present a conventional UART connector to the host and route the cable-side signals through one of the two transmitter and receiver pairs. Its 16-pin SOIC package permits placement close to the connector, which helps reduce susceptibility to radiated noise and ESD. Select the appropriate external protection network and maintain the interface ground arrangement recommended for the connected equipment.

✈️

Aerospace Support Electronics

The MAX232MWE/PR is appropriate for aerospace-support electronics where a 5 V controller must communicate with RS-232 test equipment and the equipment specification calls for the military-grade MAX232MWE configuration. The dual transceiver provides two directional interface channels without requiring separate driver and receiver ICs for each direction. The 16-SOIC package supports controlled surface-mount assembly, although the complete assembly process still determines the final thermal and workmanship assumptions. Confirm the exact ordering code, qualification requirements, and external line protection before production release.

What is the MAX232MWE/PR?
The MAX232MWE/PR is a dual RS-232 transceiver with two transmitters and two receivers in a 16-pin SOIC package. According to the Analog Devices product information, it operates from a 4.5 V to 5.5 V supply and is designated for military temperature applications. It combines the level-shifting functions required to connect a 5 V UART to an external RS-232 port.
What is the operating voltage of MAX232MWE/PR?
The MAX232MWE/PR operates from a nominal 5 V supply, with a listed operating range of 4.5 V to 5.5 V. The manufacturer datasheet should be used for absolute-maximum and decoupling requirements. This device does not accept the higher voltage used by some modern RS-232 interface circuits, so the supply rail must remain within the stated range.
How many RS-232 channels does MAX232MWE/PR provide?
The MAX232MWE/PR provides two complete RS-232 channels, consisting of two transmitters and two receivers. The manufacturer listing identifies it as a 2/2 full-RS-232 transceiver in a 16-SOIC package. This allows one logic-side UART and one external RS-232 connector to exchange data bidirectionally, including hardware flow-control signals when they are routed appropriately.
Where can I download the MAX232MWE/PR datasheet?
The MAX232MWE/PR datasheet and technical information can be reached through the Analog Devices product resources or the linked manufacturer-data page for this device. The listed document describes the dual-transceiver, dual-receiver, 16-pin SOIC configuration. Use the manufacturer datasheet for the definitive pin descriptions, charge-pump capacitor values, absolute-maximum ratings, and recommended application circuit.
Where is the MAX232MWE/PR pinout?
The MAX232MWE/PR pinout is documented in the manufacturer datasheet under the pin-description and package-information sections. The device uses a 16-pin SOIC footprint with gull-wing leads. Use that table when assigning power, ground, driver outputs, receiver inputs, and charge-pump capacitor connections, because connector-side and logic-side signal names must not be interchanged.
Where to buy MAX232MWE/PR online?
The MAX232MWE/PR can be requested through the Request a Quote form on this page. The form is the appropriate route for obtaining commercial availability, quantity, and lead-time information for the exact 16-SOIC military-grade ordering code. Confirm the package suffix, operating grade, and assembly requirements before releasing the order so the received device matches the PCB footprint.
What is the price of MAX232MWE/PR?
Current commercial pricing for the MAX232MWE/PR is obtained through the Request a Quote form on this page. The form captures the exact MPN and required quantity so availability and a current quotation can be matched to your order. The MPN identifies the 16-SOIC military-temperature configuration, which should be preserved in the quotation request to avoid a package or grade mismatch.
What is the lead time for MAX232MWE/PR?
The current lead time for MAX232MWE/PR is established through the Request a Quote form on this page. Lead time can vary with order quantity, assembly configuration, and manufacturing availability, so it is best to request the required quantity and target schedule with the inquiry. Include any planned date for a production build in the request to obtain a schedule suitable for the project timeline.
Is MAX232MWE/PR in stock?
Stock availability for MAX232MWE/PR is confirmed through the Request a Quote form on this page. Because the exact ordering code includes a 16-SOIC package and military temperature grade, the inquiry should state that suffix explicitly. The quotation response can then confirm current availability for the requested quantity without confusing the part with other MAX232 package or temperature configurations.
MAX232MWE/PR vs MAX232CWE+ - which is better for an industrial RS-232 port?
The MAX232MWE/PR is the better choice when the design specifically requires the military temperature designation; MAX232CWE+ is the commercial-temperature family configuration. Both are listed as dual-transmitter, dual-receiver RS-232 devices in 16-pin SOIC packages, so their interface functions align. The final selection should compare the complete manufacturer ordering tables for temperature limits, qualification, and lifecycle requirements.
What is the difference between MAX232MWE/PR and MAX232EWE+T?
The principal documented difference is the temperature and ordering designation: MAX232MWE/PR is identified as military grade, while MAX232EWE+T belongs to the MAX232E family configuration. Both retain the same 2-transmitter, 2-receiver RS-232 architecture and 16-SOIC package format. Verify electrical ratings, qualification, and lifecycle status against the manufacturer datasheets before treating either part as a substitute.
When should I choose MAX232MWE/PR over MAX232CWE+?
Choose MAX232MWE/PR when the equipment specification calls for the military-grade MAX232MWE configuration or requires that exact ordering code. Choose MAX232CWE+ when its commercial temperature range satisfies the product specification and a more readily sourced configuration is preferred. Both provide the same fundamental two-channel RS-232 transceiver function, so environmental qualification should drive the decision.
Is MAX232MWE/PR suitable for a bidirectional serial interface?
Yes, MAX232MWE/PR is suitable for a bidirectional RS-232 interface because it contains two transmitters and two receivers. The logic-side connections interface with a UART, while the line-side connections communicate through an RS-232 connector. Add suitable external protection for exposed cables and follow the manufacturer charge-pump capacitor recommendations to maintain reliable operation.
What can replace MAX232MWE/PR?
The closest drop-in choices include MAX232CWE+, MAX232EWE+T, MAX232ACWE+, and MAX232AEWE+ when their manufacturer ordering tables confirm the required footprint and environmental grade. A replacement is appropriate only after checking pin assignments, temperature limits, supply requirements, and qualification. Packaging and grade differences can matter even when the RS-232 channel count is identical.
What is the best cross-brand equivalent for MAX232MWE/PR?
A cross-brand equivalent should be selected only after its manufacturer confirms a pin-for-pin 16-pin SOIC footprint and equivalent RS-232 electrical ratings. The available cross-reference material identifies several possible MAX232 replacements, but it does not expose enough part-level detail to qualify a specific cross-brand MPN safely. Use the manufacturer pinout and ordering tables, then request the chosen exact MPN through the Request a Quote form.

کے لیے انجینئرنگ ریفرنس ڈیٹا MAX232MWE/PR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose MAX232MWE/PR when the system specification calls for the military-grade MAX232MWE configuration, a 5 V RS-232 interface, and a 16-pin SOIC footprint. MAX232CWE+ is appropriate when commercial-temperature limits are sufficient and the lower-temperature family configuration is preferred. MAX232EWE+T can be considered when its ordering, qualification, and environmental details satisfy the product requirements. MAX232ACWE+ and MAX232AEWE+ are useful same-family options when the manufacturer ordering table confirms the required temperature and qualification range. In every case, verify pin assignments, charge-pump capacitor requirements, electrical limits, and lifecycle status. A footprint match alone does not resolve differences in temperature grade or qualification, so the environmental specification must drive the final choice.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ MAX232CWE+ MAX232EWE+T MAX232ACWE+ MAX232AEWE+ MAX232MWE/PR+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Interface RS-232 RS-232 RS-232 RS-232 RS-232 RS-232
Number of Transmitters 2 2 2 2 2 2
Number of Receivers 2 2 2 2 2 2
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V

اہم امتیازی خصوصیات

  • Military-grade ordering configuration (بمقابلہMAX232CWE+)
  • Two complete bidirectional RS-232 channels (بمقابلہMAX232EWE+T)
  • Exact same-family footprint reuse (بمقابلہMAX232MWE/PR+)

ڈیزائن نوٹس

Place the MAX232MWE/PR close to the RS-232 connector so the cable-side driver and receiver nets remain short. Keep the logic-side UART traces away from these nets, use a continuous ground reference, and avoid routing the interface through areas dominated by switching nodes. Place connector protection at the boundary of the PCB so surge or electrostatic discharge current is diverted before reaching the transceiver.

Use the manufacturer-recommended charge-pump capacitors and supply-bypass arrangement without changing their values or increasing their distance from the associated pins. The MAX232MWE/PR operates from 4.5 V to 5.5 V, so verify the supply range across tolerance, startup, and load transients. A stable 5 V rail is essential because the charge-pump and receiver thresholds support the bipolar RS-232 signaling scheme.

Do not interchange the logic-side UART pins with the cable-side RS-232 pins. Driver outputs connect to the external RS-232 line, while receiver inputs accept the external line; reversing them can prevent communication or expose the interface to incorrect signal levels. Also verify the exact temperature grade and package suffix during inspection, because MAX232 family members share a similar 16-pin interface but may use different environmental qualifications.

Treat the cable-side receiver nodes as sensitive, high-impedance nets and keep them away from clocks, relays, power inductors, and fast digital edges. Use the shortest practical route from the connector to the receiver pins and provide a direct chassis or signal-ground strategy appropriate to the connected equipment. External protection is still required because the PCB transceiver alone does not provide a complete industrial surge-protection solution.

تعمیل کی معلومات

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Yes
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The listed terminal finish is annealed matte tin with JESD-609 code e3. RoHS compliance is indicated by the product ordering information, while REACH, halogen-free, and conflict-minerals status are not established by the cited product information.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-17 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

MAX232MWE/PR datasheet MAX232MWE/PR pinout MAX232MWE/PR datasheet pdf MAX232MWE/PR equivalent MAX232MWE/PR replacement MAX232MWE/PR cross reference MAX232MWE/PR vs MAX232CWE+ MAX232MWE/PR price MAX232MWE/PR stock Analog Devices MAX232MWE/PR MAX232MWE/PR 16-SOIC MAX232MWE/PR RS-232 interface MAX232MWE/PR industrial application what is MAX232MWE/PR

متعلقہ اجزاء اور اصطلاحات

Analog Devices MAX232MWE/PR MAX232CWE+ MAX232EWE+T MAX232ACWE+ MAX232AEWE+ MAX232MWE/PR+ RS-232 RS-232 transceiver line driver line receiver UART interface IC semiconductor dual transmitter dual receiver 5 V power supply 4.5 V to 5.5 V operating range military temperature grade 16-SOIC SOIC package family surface mount SMD charge-pump capacitor RS-232 connector RoHS JESD-609 MSL 1 matte tin terminal finish industrial electronics aerospace support electronics legacy serial communication
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں