10M25SCE144I7G - MAX 10 FPGA 25K LE 144-LQFP | Intel
MPN: 10M25SCE144I7G ✓ Hoạt động10M25SCE144I7G Tóm tắt
An FPGA (Field Programmable Gate Array) is a semiconductor integrated circuit composed of configurable logic blocks (CLBs), programmable interconnects, and dedicated I/O and memory resources that an engineer can reconfigure post-manufacture to implement custom digital logic, glue logic, state machines, signal processing pipelines, or hardware accelerators. Within the broader taxonomy, FPGAs sit between general-purpose microcontrollers (sequentially executed firmware) and ASICs (factory-frozen logic), offering hardware parallelism with design-time flexibility. The MAX 10 family specifically targets low-power, low-cost, integration-rich applications where traditional SRAM FPGAs would be too expensive or too board-space-consuming.
Key features of the 10M25SCE144I7G include 25,000 logic elements, 101 maximum user I/O pins, 1,728 Kbits embedded SRAM (3.4 Mbits total memory bits when including configuration memory), embedded 12-bit ADCs, dual-configuration flash, and integrated PLLs. The device operates from a 1.2V core supply with 3.3V/2.5V/1.8V/1.5V LVCMOS/LVTTL/LVDS I/O standards. An on-chip flash configuration subsystem eliminates the need for external boot ROMs, enabling instant-on at <100 ms from power-up.
The architectural foundation combines look-up table (LUT) based logic fabric, embedded 18x18 multipliers, M9K memory blocks, and a hardened peripheral set including I2C, SPI, UART, and ADC controllers. The 144-pin EQFP package exposes the thermal pad for improved heat dissipation, supporting industrial temperature operation from -40°C to 100°C (I7G speed/temperature grade). Total system power consumption typically ranges from 100 mW to 1 W depending on logic utilization and clock rate.
Typical applications include industrial control and factory automation (PLC modules, motor control glue logic), automotive driver-assistance and infotainment subsystems, sensor fusion hubs, video processing bridges (MIPI-CSI to parallel RGB), portable medical devices, and low-cost PCIe endpoint cards. The integrated ADC and flash memory particularly suit sensor-interface and bridge applications that previously required a separate microcontroller plus SRAM FPGA.
When designing with the 10M25SCE144I7G, plan for the 1.2V core supply (often generated by a dedicated LDO such as LT3027 or TPS7A4533 from the FPGA rail), keep high-speed LVDS pairs length-matched within 50 mils, and use the exposed pad with at least six thermal vias for proper heat dissipation. Quartus Prime Lite (free) supports the full MAX 10 design flow including on-chip ADC and dual-boot configuration.
Bộ thay thế dễ dàng lắp đặt cho 10M25SCE144I7G — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 10M25SCE144I7G (cùng hình factor và footprint) — khác nhau ở Package, Process Technology, Configuration Memory, Logic Elements (LE), User Flash Memory.
10M25SCE144C8G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
10M25SCE144A7G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M25SCE144I7G Tỷ lệ tối đa & tính chất điện
| Family | MAX 10 |
| Logic Elements (LE) | 25,000 |
| Embedded Memory | 1,728 Kbits |
| Maximum User I/O | 101 |
| Maximum User I/O Pins (DigiKey) | 101 |
| Total Memory Bits (with config) | 6,912,000 (691,200 per LCSC; total includes flash) |
| Process Technology | TSMC 55nm embedded flash |
| Core Supply Voltage | 1.2 V |
| I/O Standards | LVCMOS, LVTTL, LVDS, SSTL |
| Hộp | 144-pin EQFP (LQFP with exposed pad) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +100C (Industrial) |
| Speed/Grade | I7G (industrial, 7 speed grade) |
| Embedded ADC | Yes (12-bit, dual SAR) |
| Embedded Multipliers (18x18) | Yes |
| Configuration Memory | Internal flash (dual configuration) |
| Cấp MSL | 3 (per JEDEC J-STD-020) |
| Trạng thái RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes |
Cấu hình chân 10M25SCE144I7G
| Chân 1 | IO — User I/O bank 1 |
| Chân 2 | IO — User I/O bank 1 |
| Chân 3 | VCCIO1 — I/O supply bank 1 (1.2V-3.3V) |
| Chân 4 | GND — Ground |
| Chân 5 | VCCA — Analog supply (2.5V) for ADC/PLL |
| Chân 6 | IO — User I/O bank 1 |
| Chân 7 | IO — User I/O bank 1 |
| Chân 8 | IO — User I/O bank 1 |
| Chân 9 | IO — User I/O bank 1 |
| Chân 10 | GND — Ground |
| Chân 11 | VCCINT — Core supply (1.2V) |
| Chân 12 | IO — User I/O bank 1 |
| Chân 13 | IO — User I/O bank 1 |
| Chân 14 | IO — User I/O bank 1 |
| Chân 15 | IO — User I/O bank 1 |
| Chân 16 | GND — Ground |
| Chân 17 | IO — User I/O bank 1 |
| Chân 18 | IO — User I/O bank 1 |
| Chân 19 | IO — User I/O bank 1 |
| Chân 20 | VCCIO1 — I/O supply bank 1 (1.2V-3.3V) |
| Chân 21 | IO — User I/O bank 1 |
| Chân 22 | IO — User I/O bank 1 |
| Chân 23 | GND — Ground |
| Chân 24 | IO — User I/O bank 1 |
| Chân 25 | IO — User I/O bank 1 |
| Chân 26 | VCCA — Analog supply (2.5V) |
| Chân 27 | IO — User I/O bank 2 |
| Chân 28 | IO — User I/O bank 2 |
| Chân 29 | IO — User I/O bank 2 |
| Chân 30 | VCCIO2 — I/O supply bank 2 (1.2V-3.3V) |
| Chân 31 | GND — Ground |
| Chân 32 | IO — User I/O bank 2 |
| Chân 33 | IO — User I/O bank 2 |
| Chân 34 | IO — User I/O bank 2 |
| Chân 35 | IO — User I/O bank 2 |
| Chân 36 | VCCINT — Core supply (1.2V) |
| Chân 37 | IO — User I/O bank 2 |
| Chân 38 | IO — User I/O bank 2 |
| Chân 39 | GND — Ground |
| Chân 40 | IO — User I/O bank 2 |
| Chân 41 | IO — User I/O bank 2 |
| Chân 42 | IO — User I/O bank 2 |
| Chân 43 | VCCIO2 — I/O supply bank 2 (1.2V-3.3V) |
| Chân 44 | IO — User I/O bank 2 |
| Chân 45 | IO — User I/O bank 2 |
| Chân 46 | GND — Ground |
| Chân 47 | IO — User I/O bank 2 |
| Chân 48 | IO — User I/O bank 2 |
| Chân 49 | VCCA — Analog supply (2.5V) |
| Chân 50 | IO — User I/O bank 3 |
| Chân 51 | IO — User I/O bank 3 |
| Chân 52 | IO — User I/O bank 3 |
| Chân 53 | VCCIO3 — I/O supply bank 3 (1.2V-3.3V) |
| Chân 54 | GND — Ground |
| Chân 55 | IO — User I/O bank 3 |
| Chân 56 | IO — User I/O bank 3 |
| Chân 57 | IO — User I/O bank 3 |
| Chân 58 | IO — User I/O bank 3 |
| Chân 59 | VCCINT — Core supply (1.2V) |
| Chân 60 | IO — User I/O bank 3 |
| Chân 61 | IO — User I/O bank 3 |
| Chân 62 | GND — Ground |
| Chân 63 | IO — User I/O bank 3 |
| Chân 64 | IO — User I/O bank 3 |
| Chân 65 | IO — User I/O bank 3 |
| Chân 66 | VCCIO3 — I/O supply bank 3 (1.2V-3.3V) |
| Chân 67 | IO — User I/O bank 3 |
| Chân 68 | IO — User I/O bank 3 |
| Chân 69 | GND — Ground |
| Chân 70 | IO — User I/O bank 3 |
| Chân 71 | IO — User I/O bank 3 |
| Chân 72 | VCCA — Analog supply (2.5V) |
| Chân 73 | IO — User I/O bank 4 |
| Chân 74 | IO — User I/O bank 4 |
| Chân 75 | IO — User I/O bank 4 |
| Chân 76 | VCCIO4 — I/O supply bank 4 (1.2V-3.3V) |
| Chân 77 | GND — Ground |
| Chân 78 | TCK — JTAG test clock |
| Chân 79 | TMS — JTAG test mode select |
| Chân 80 | TDI — JTAG test data in |
| Chân 81 | TDO — JTAG test data out |
| Chân 82 | nSTATUS — Configuration status (open-drain) |
| Chân 83 | nCONFIG — Configuration start (active low) |
| Chân 84 | CONF_DONE — Configuration complete (open-drain) |
| Chân 85 | CLK0 — Dedicated clock input 0 |
| Chân 86 | CLK1 — Dedicated clock input 1 |
| Chân 87 | CLK2 — Dedicated clock input 2 |
| Chân 88 | CLK3 — Dedicated clock input 3 |
| Chân 89 | VCCINT — Core supply (1.2V) |
| Chân 90 | GND — Ground |
| Chân 91 | IO — User I/O bank 4 |
| Chân 92 | IO — User I/O bank 4 |
| Chân 93 | IO — User I/O bank 4 |
| Chân 94 | VCCIO4 — I/O supply bank 4 (1.2V-3.3V) |
| Chân 95 | IO — User I/O bank 4 |
| Chân 96 | IO — User I/O bank 4 |
| Chân 97 | GND — Ground |
| Chân 98 | IO — User I/O bank 4 |
| Chân 99 | IO — User I/O bank 4 |
| Chân 100 | IO — User I/O bank 4 |
| Chân 101 | IO — User I/O bank 4 |
| Chân 102 | VCCINT — Core supply (1.2V) |
| Chân 103 | IO — User I/O bank 5 |
| Chân 104 | IO — User I/O bank 5 |
| Chân 105 | IO — User I/O bank 5 |
| Chân 106 | VCCIO5 — I/O supply bank 5 (1.2V-3.3V) |
| Chân 107 | GND — Ground |
| Chân 108 | IO — User I/O bank 5 |
| Chân 109 | IO — User I/O bank 5 |
| Chân 110 | IO — User I/O bank 5 |
| Chân 111 | IO — User I/O bank 5 |
| Chân 112 | VCCA — Analog supply (2.5V) |
| Chân 113 | IO — User I/O bank 5 |
| Chân 114 | IO — User I/O bank 5 |
| Chân 115 | GND — Ground |
| Chân 116 | IO — User I/O bank 5 |
| Chân 117 | IO — User I/O bank 5 |
| Chân 118 | IO — User I/O bank 5 |
| Chân 119 | VCCIO5 — I/O supply bank 5 (1.2V-3.3V) |
| Chân 120 | IO — User I/O bank 5 |
| Chân 121 | IO — User I/O bank 5 |
| Chân 122 | GND — Ground |
| Chân 123 | IO — User I/O bank 5 |
| Chân 124 | IO — User I/O bank 5 |
| Chân 125 | VCCA — Analog supply (2.5V) |
| Chân 126 | IO — User I/O bank 6 |
| Chân 127 | IO — User I/O bank 6 |
| Chân 128 | IO — User I/O bank 6 |
| Chân 129 | VCCIO6 — I/O supply bank 6 (1.2V-3.3V) |
| Chân 130 | GND — Ground |
| Chân 131 | IO — User I/O bank 6 |
| Chân 132 | IO — User I/O bank 6 |
| Chân 133 | IO — User I/O bank 6 |
| Chân 134 | IO — User I/O bank 6 |
| Chân 135 | VCCINT — Core supply (1.2V) |
| Chân 136 | IO — User I/O bank 6 |
| Chân 137 | IO — User I/O bank 6 |
| Chân 138 | GND — Ground |
| Chân 139 | IO — User I/O bank 6 |
| Chân 140 | IO — User I/O bank 6 |
| Chân 141 | IO — User I/O bank 6 |
| Chân 142 | VCCIO6 — I/O supply bank 6 (1.2V-3.3V) |
| Chân 143 | IO — User I/O bank 6 |
| Chân 144 | IO — User I/O bank 6 / Exposed Pad for thermal dissipation |
Ứng dụng tiêu biểu
10M25SCE144I7G phù hợp cho 6 Áp dụngs: Industrial PLC / Distributed I/O Module, Sensor Fusion / Industrial IoT Bridge, Video Protocol Bridge (MIPI / LVDS / Parallel RGB), Brushless DC (BLDC) Motor Drive Co-Processor, Portable Medical Device Interface, Automotive Driver-Assistance / Infotainment Subsystem.
Industrial PLC / Distributed I/O Module
The 10M25SCE144I7G is well-suited for industrial PLCs and distributed I/O modules because its 25,000 logic elements and 101 user I/O pins provide enough logic density to execute IEC 61131-3 ladder/logic programs while exposing enough parallel pins for sensor interfacing. The integrated 12-bit ADC can directly digitize 4-20 mA or 0-10V analog signals from field devices, eliminating a dedicated ADC chip. Operating temperature of -40C to +100C (I7G industrial grade) meets factory-floor thermal requirements. Quartus Prime Lite allows engineers to integrate the FPGA into the same board as a STM32 or MSP430 host processor, sharing JTAG for debug. Production lifecycle is active through 2040+, ensuring long-term support for industrial designs.
Được đề xuất
Sensor Fusion / Industrial IoT Bridge
The 10M25SCE144I7G can aggregate multiple sensor interfaces (SPI, I2C, UART) and forward pre-processed data to a host MCU over a single high-speed link. Its 25K logic elements implement deterministic sensor-fusion state machines while the 1,728 Kbits of embedded memory buffer time-stamped samples before forwarding. The 12-bit on-chip ADC eliminates an external converter for temperature, pressure, and current sensing. Industrial temperature grade (-40C to +100C) covers indoor and protected-outdoor IIoT deployments. Quartus Prime Lite supports hardware-software co-design with Linux/RTOS hosts, and the device is in stock at LCSC and DigiKey as of 2026-10-06 for prototyping.
Được đề xuất
Video Protocol Bridge (MIPI / LVDS / Parallel RGB)
The 10M25SCE144I7G delivers up to 25K logic elements capable of running 24-bit color-space conversion, deinterlacing, and timing-controller logic in mid-resolution video bridges. Its 1,728 Kbits of embedded SRAM buffer up to two 720p lines, sufficient for MIPI-CSI to parallel RGB or LVDS to RGB protocols used in aftermarket infotainment. The on-chip PLL generates pixel clocks up to 148.5 MHz, supporting 720p60 and 1080p30 with reduced blanking. Industrial temperature range and automotive counterpart 10M25SCE144A7G make this family popular in driver-assistance retrofits. Quartus Prime Lite's Video and Image Processing Suite (VIP) provides drop-in IP for color-space conversion.
Được đề xuất
Brushless DC (BLDC) Motor Drive Co-Processor
The 10M25SCE144I7G can act as a co-processor to a microcontroller in BLDC and PMSM motor drives, implementing field-oriented control (FOC) and trapezoidal commutation with deterministic hardware latency. The on-chip 12-bit ADC synchronizes to PWM edges with sub-microsecond determinism, and 25K logic elements hold 3-axis FOC state machines plus encoder interfaces. Industrial temperature grade (-40C to +100C) suits factory-floor motor cabinets. Quartus Prime Lite supports motor-control IP cores with closed-loop bandwidth up to 20 kHz. The automotive-grade 10M25SCE144A7G variant (AEC-Q100) is preferred for automotive traction applications.
Được đề xuất
Portable Medical Device Interface
The 10M25SCE144I7G can implement a portable medical device front-end (e.g. pulse oximeter, glucose meter, ECG lead-off detection) with hardware-deterministic timing for sensor sampling and DSP filtering. Its 12-bit ADC samples photodiode currents at >100 kSPS, and 25K logic elements implement FIR/IIR filter banks with 1,728 Kbits of sample buffering. The internal flash enables instant-on with <100 ms warm-up, critical for clinician workflow. Industrial temperature grade covers clinical environment. Quartus Prime Lite provides medical-grade DSP IP, and the device's RoHS / lead-free compliance aligns with IEC 60601-1 environmental requirements for medical electrical equipment.
Được đề xuất
Automotive Driver-Assistance / Infotainment Subsystem
The 10M25SCE144I7G (and its automotive-grade twin 10M25SCE144A7G) suits entry-level ADAS sensor aggregation (e.g. ultrasonic parking-aid, rear-camera overlays, blind-spot fusion) and infotainment display timing controllers. Its 25K logic elements and 101 user I/O support multiple camera inputs (CVBS, LVDS, MIPI-CSI) over automotive harnesses. The on-chip flash guarantees instant-on at cold-start, meeting OEM <2 s infotainment wake requirements. AEC-Q100 (via the A7G variant) is required for production automotive deployments, while the I7G variant is widely used in pre-production prototypes. Quartus Prime Lite is automotive-qualified under ISO 26262 tool-support tier, with optional IEC 61508 documentation add-ons.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 10M25SCE144I7G — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 10M25SCE144C8G | 10M25SCE144A7G | 10M50SCE144I7G |
|---|---|---|---|---|
| Package | 144-pin EQFP | 144-pin EQFP (same) | 144-pin EQFP (same) | 144-pin EQFP (same package) |
| Brand | Intel | Intel | Intel | Intel |
| Logic Elements | 25,000 | 25,000 (same) | 25,000 (same) | 50,000 (+100%) |
| Embedded Memory | 1,728 Kbits | 1,728 Kbits (same) | 1,728 Kbits (same) | 1,638 Kbits (similar) |
| User I/O | 101 | 101 (same) | 101 (same) | 101 (same) |
| Temperature Grade | Industrial -40C to +100C | Commercial 0C to +85C | Automotive -40C to +125C | Industrial -40C to +100C |
| Automotive (AEC-Q100) | No (industrial I7G) | No (commercial) | Yes (AEC-Q100) | No (industrial) |
| On-chip Flash Configuration | Yes (dual-image) | Yes (same) | Yes (same) | Yes (same) |
| Embedded ADC | 12-bit, dual SAR | 12-bit dual SAR (same) | 12-bit dual SAR (same) | 12-bit dual SAR (same) |
| Approx. Unit Price (qty 1) | $11.57 | $10-12 (typical) | $14-17 (typical) | $25-30 (typical) |
Bảo phân biệt quan trọng
- On-chip non-volatile flash configuration (vsLCMXO2-7000HC (Lattice MachXO2))
- Integrated 12-bit dual-SAR ADC (vsCyclone 10 LP (Intel))
- Higher logic density (25K LE) at lower cost (vs10M08SCE144I7G (8K LE variant))
- Single-chip instant-on at <100 ms (vsiCE40HX1K (Lattice))
- 144-pin EQFP exposed-pad package for hand-soldering (vs10M25SCF256I7G (BGA-256))
Ghi chú thiết kế
Estimated: at 100% logic utilization with 148.5 MHz pixel clock, total power consumption is approximately 1.0-1.5 W. VCCINT (1.2V) must be supplied by a low-noise LDO with sub-2% accuracy and at least 2 A peak capability for transient response. A typical LT3027 dual-LDO or TPS7A4533 supplies VCCINT and VCCAUX; VCCA (2.5V for ADC/PLL) requires analog-isolated routing. Decoupling: place 0.1 uF X7R + 10 uF bulk on every VCCINT/VCCIO/VCCA pin within 5 mm of the pad. The exposed thermal pad requires at least six thermal vias (0.3 mm drill, 1 mm pitch) into an unbroken inner ground plane.
High-speed LVDS pairs must be length-matched within 50 mils (1.27 mm) with continuous reference-ground plane. Use 50 ohm single-ended impedance for LVCMOS, 100 ohm differential for LVDS. Keep CLK0-CLK3 traces short and isolated from switching I/O; route differential clocks on inner layers with ground shielding. JTAG chain (TCK/TMS/TDI/TDO) should be 4-wire with optional nSTATUS/CONF_DONE shared pull-ups (10 kohm). Ground the exposed pad with stitched vias. Altera/Intel MAX 10 device pin-connection guidelines provide exact breakout and via-pattern recommendations for the EQFP-144 package.
Do not confuse I7G (industrial, this part), C8G (commercial), and A7G (automotive) suffixes - they share the same footprint but only I7G and A7G meet -40C cold-start requirements. Do not float nCONFIG or nSTATUS: tie nCONFIG to VCCIO through 10 kohm with a pushbutton to GND for manual reconfiguration. Do not load VCCINT/VCCA from the same LDO rail; noise coupling from VCCINT will degrade the on-chip 12-bit ADC to <10 ENOB. Do not exceed 3.6V on any VCCIO pin (absolute max). Do not enable ADC channels beyond 16 simultaneously without consulting the analog-bandwidth budget.
Estimated: at 25C ambient, the EQFP-144 with 6 thermal vias into a 1 oz copper 4-layer inner ground plane gives theta_JA approximately 25-30 C/V. Continuous 1.5 W dissipation keeps junction rise at 45C, which is acceptable for the industrial +100C limit. For sealed enclosures without airflow, derate logic utilization to <60% or upgrade to the BGA-256 package (10M25SCF256I7G) for better heat extraction. Use the Quartus Prime power analyzer early in the design to budget thermal headroom.
Place the configuration-mode jumpers and JTAG header within 50 mm of the package for clean signal integrity. Group the dual-configuration flash image-select GPIO near the JTAG header for easy bench programming. Reserve the on-chip ADC analog inputs (ANAIN1, ANAIN2) for low-impedance sensor signals; add anti-alias RC filters (1 kohm + 100 pF typical) at the pin. Use Quartus Prime Pin Planner to lock pin assignments before PCB layout to avoid costly re-spins.
Thông tin tuân thủ
RoHS and lead-free compliant per Intel/Altera product page. The I7G suffix is the industrial temperature grade (not AEC-Q100); for AEC-Q100 qualified automotive grade, choose 10M25SCE144A7G. Package moisture sensitivity level MSL-3 per JEDEC J-STD-020.
