AD5316ARU - Quad 10-Bit DAC, 2.5-5.5V | Analog Devices
MPN: AD5316ARU ✓ Hoạt độngAD5316ARU Tóm tắt
A digital-to-analog converter is an interface IC that converts digital control words into proportional analog voltages. The AD5316 belongs to the DAC hierarchy, where it sits between a digital bus and precision analog test, control, or instrumentation circuitry. Its buffered outputs reduce the need for external output amplifiers when driving moderate loads.
The four converters provide 10-bit resolution, and the A-grade device has an integral nonlinearity specification of ±4 LSB. On-chip output amplifiers support rail-to-rail output swing with a slew rate of 0.7 V/µs. The single-supply operating range covers both 3.3 V and 5 V systems, while the typical supply current is 500 µA at 3 V for low-power portable and industrial designs.
The AD5316 uses a 2-wire serial interface operating up to 400 kHz and is compatible with SMBus-style communication. Each channel provides an independently programmable output voltage through its corresponding DAC register. The interface allows a microcontroller, embedded processor, or programmable controller to update four analog outputs while minimizing the number of signal connections required on the PCB.
Typical applications include process-control setpoints, automated test equipment, sensor excitation and bias control, industrial data acquisition, programmable laboratory supplies, and low-power embedded instrumentation. The quad-channel arrangement is particularly useful when a system requires several independently controlled analog outputs but has limited connector and routing space.
PCB design should keep the serial interface and output routing compact while observing the analog-ground and supply-return paths recommended in the manufacturer datasheet. Decoupling capacitance should be placed close to the supply pins, and output loads should be checked against the buffered-output capabilities. The 0.7 V/µs slew rate should also be considered when designing waveforms that require rapid output transitions.
This page combines the manufacturer's device characteristics, package and interface details, comparison guidance, and practical application guidance to help engineers evaluate the AD5316ARU without relying only on a basic catalog listing.
Bộ thay thế dễ dàng lắp đặt cho AD5316ARU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD5316ARUZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD5316ARU-REEL7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD5306ARUZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD5317BRUZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD5316RBRUZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD5316ARU Tỷ lệ tối đa & tính chất điện
| Number of DAC Channels | 4 channels |
| DAC Resolution | 10 bits |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Typical Supply Current | 500 µA at 3 V |
| Kiểu đầu ra | Buffered voltage output |
| Output Swing | Rail-to-rail |
| Output Slew Rate | 0.7 V/µs |
| Integral Nonlinearity | ±4 LSB for A grade |
| Serial Interface | 2-wire serial interface |
| Maximum Serial Clock Rate | 400 kHz |
| Serial Interface Compatibility | SMBus-compatible |
| Reference Type | External reference |
| Hộp | 16-lead TSSOP |
| Số lượng chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
| Khoảng nhiệt độ hoạt động | -40 °C to +105 °C |
| Screening Level | Industrial |
| Power Dissipation | 2.5 mW |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
Hướng dẫn cấu hình chân AD5316ARU 16-lead tssop
Cấu hình chân cho AD5316ARU (16-lead tssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD5316ARU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD5316ARU phù hợp cho 6 Áp dụngs: Industrial Process Control, Programmable Test Equipment, Sensor Excitation and Biasing, Programmable Laboratory Supplies, Data Acquisition Systems, Embedded Instrumentation.
Industrial Process Control
The AD5316ARU fits four-channel process-control systems that must convert digital setpoints into analog actuator commands. Its 10-bit resolution provides 1,024 codes per channel, while the four buffered outputs allow multiple control loops to share one controller. The 2-wire interface operates up to 400 kHz, reducing wiring in distributed control equipment, and the 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V industrial controller platforms. Verify the external reference, output range, and load impedance against each loop before production deployment.
Được đề xuất
Programmable Test Equipment
The AD5316ARU can generate up to four independent analog test stimuli in programmable instrumentation. A 10-bit command word gives each channel 1,024 output levels, which is useful for coarse source calibration, relay or amplifier control, and fixture biasing. Its 400 kHz 2-wire interface allows a test controller to load a sequence of channel values efficiently, while buffered outputs reduce the need for separate output amplifiers. For metrology paths demanding finer resolution, use a higher-resolution DAC and recalibrate the source path.
Được đề xuất
Sensor Excitation and Biasing
The AD5316ARU is suitable for multi-channel sensor-bias and excitation systems where four independently adjustable voltages are needed. By placing each DAC output near the associated input network, the 2-wire architecture reduces routing across a measurement board. The 0.7 V/µs output slew rate supports relatively quick settling after code changes, and the low 500 µA typical supply current at 3 V suits compact acquisition modules. Confirm output settling at the required accuracy and ensure the external reference does not introduce noise into the measurement front end.
Được đề xuất
Programmable Laboratory Supplies
A laboratory supply controller can use the AD5316ARU to generate four low-level voltage commands for DUT bias, limit setting, or calibration fixtures. The device's 10-bit resolution and rail-to-rail buffered outputs are appropriate when the control path does not require ultra-high precision. Since the outputs are voltage commands rather than direct power-stage drivers, the design should add appropriate amplifiers when driving heavier loads. The 400 kHz serial rate permits coordinated multi-channel updates, which is useful for matching polarity or level changes across a fixture.
Được đề xuất
Data Acquisition Systems
The AD5316ARU can supply programmable control or excitation voltages in compact data-acquisition equipment. Four channels let the acquisition controller manage several analog output functions without allocating a separate DAC package for each signal. The 2.5 V minimum supply supports low-voltage embedded designs, while the typical 500 µA current at 3 V helps limit power demand. The serial interface should be routed away from high-gain analog inputs, and the reference and DAC return paths should be arranged according to the manufacturer's layout guidance.
Được đề xuất
Embedded Instrumentation
The AD5316ARU is appropriate for embedded instrumentation that needs multiple analog control outputs without adding extensive digital wiring. Its four 10-bit channels and SMBus-compatible 2-wire interface align with microcontroller-based instrumentation, while the TSSOP-16 package supports compact board layouts. The buffered outputs can drive normal instrumentation signal-conditioning inputs, but external buffering may be required for high capacitance or long cable runs. Account for the 0.7 V/µs slew rate when sequencing commands through switched test paths.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD5316ARU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD5316ARUZ | AD5316ARU-REEL7 | AD5306ARUZ | AD5317BRUZ | AD5316RBRUZ |
|---|---|---|---|---|---|---|
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of DAC Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
Bảo phân biệt quan trọng
- Exact AD5316ARU ordering configuration (vsAD5316ARUZ)
- Balanced resolution for multichannel control (vsAD5306ARUZ)
- External-reference architecture (vsAD5316RBRUZ)
Ghi chú thiết kế
Place the supply bypass capacitor directly between the supply and ground pins, and keep the external reference and reference-return traces short. Route the 2-wire interface away from the four analog outputs and sensitive input circuits. The TSSOP-16 footprint is compact, so leaving adequate spacing around the pins improves soldering access and reduces the chance of accidental bridges between adjacent nets.
Use the manufacturer pin-description table when assigning the SDA-like clock, SCL-like data, reference, supply, ground, and four analog-output nets. Verify that each output trace has a return path and is not routed beside a switching node. If an output drives a capacitive load, keep the load modest or add an isolation resistor and external buffer because the 0.7 V/µs slew rate can produce edge-related settling and crosstalk.
Do not treat a family member with the same package as automatically interchangeable. Confirm pin numbering, accuracy grade, temperature rating, reference voltage, output range, interface protocol, and ordering suffix before replacing the AD5316ARU. The AD5316R family adds an internal reference and power-on-reset functionality, so its control behavior may differ even though all listed alternatives use a TSSOP-16 package.
Thông tin tuân thủ
The device is described as an industrial-grade component, but no specific RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is stated on the manufacturer product page. The AD5316ARU is not presented as an AEC-Q100-qualified automotive device.