AD976ACRS - 16-Bit 200 kSPS ADC | Analog Devices
MPN: AD976ACRS ✓ Hoạt độngAD976ACRS Tóm tắt
An ADC is an analog-to-digital converter, a semiconductor that converts a continuously varying analog voltage into a numerical value. Within the signal-chain hierarchy, the AD976ACRS belongs to the data-converter IC class and specifically to high-resolution, parallel-output successive-approximation ADCs. The AD976A family combines a 16-bit conversion word with a 200 kSPS sampling rate, making it suitable for precision instrumentation, industrial measurement, communications, and control systems.
Key features include single 5 V operation, a switched-capacitor conversion architecture, selectable external or internal 2.5 V reference, an on-chip clock, and a high-speed parallel interface. The manufacturer identifies the converter as a BiCMOS device, combining bipolar circuitry with CMOS logic. Maximum power dissipation is 100 mW, making the part suitable for compact systems where converter power must remain controlled.
The AD976ACRS accepts an analog input range of 0 to 5 V when operated from the specified single supply. The AD976A family is available in 28-lead SSOP and SOIC formats, while the closely related AD976 family offers a lower 100 kSPS throughput rate. An external 200 ohm resistor and 33.2 kohm resistor can provide offset-and-gain calibration in a single-supply system when the required application calls for external adjustment.
Typical applications include industrial process-control equipment, digital instrumentation, waveform acquisition, communications receivers, and embedded measurement systems. The parallel bus can feed a microcontroller, FPGA, or dedicated data-capture logic, while the on-chip clock simplifies systems that do not require an external sampling clock. Analog input conditioning remains important because the ADC does not replace front-end amplification, filtering, or reference conditioning.
Designers should follow the manufacturer pin-description table when assigning tracks and should place input, reference, and decoupling connections according to the AD976/AD976A datasheet layout guidance. Confirm signal range, conversion timing, reference stability, and output logic levels before fixing the clock and acquisition system. For applications requiring the faster 200 kSPS rate, use the AD976A rather than the 100 kSPS AD976.
Bộ thay thế dễ dàng lắp đặt cho AD976ACRS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD976ACRS (cùng hình factor và footprint) — khác nhau ở Output Interface, Package, Process Technology, Architecture, Converter Type.
AD976ACRSZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD976AARSZ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →AD976ACRS Tỷ lệ tối đa & tính chất điện
| Converter Type | 16-bit successive-approximation ADC |
| Throughput Rate | 200 kSPS |
| Điện áp cung cấp | 5 V |
| Input Range | 0 V to 5 V |
| Internal Reference | 2.5 V |
| Reference Selection | Internal or external reference |
| Maximum Power Dissipation | 100 mW |
| Architecture | Switched-capacitor |
| Process Technology | BiCMOS |
| Output Interface | High-speed parallel |
| Clock | On-chip clock |
| Hộp | 28-lead SSOP |
| Số lượng chân | 28 pins |
| Kiểu lắp đặt | Surface mount |
| Calibration Resistor | 200 ohm |
| Calibration Resistor | 33.2 kohm |
Hướng dẫn cấu hình chân AD976ACRS 28-lead ssop
Cấu hình chân cho AD976ACRS (28-lead ssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD976ACRS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD976ACRS phù hợp cho 6 Áp dụngs: Industrial Process Measurement, Digital Instrumentation, Communications Receiver, Waveform Acquisition, Precision Feedback Control, Automated Test Equipment.
Industrial Process Measurement
AD976ACRS fits industrial process-measurement front ends that require 16-bit numerical resolution at a 200 kSPS conversion rate. Place the converter after a low-noise amplifier and analog filter so that process signals arrive within the 0 V to 5 V input range. Its single 5 V operation simplifies the supply architecture, while the parallel output can feed an FPGA or controller for real-time filtering. The 200 mW maximum power-dissipation rating supports compact measurement electronics, although designers should still verify thermal performance in the final enclosure.
Được đề xuất
Digital Instrumentation
AD976ACRS is appropriate for bench instruments and digital measurement equipment that sample precision analog inputs while transferring data through a parallel bus. Its 16-bit resolution preserves fine signal detail, and the 200 kSPS throughput provides a higher acquisition rate than the 100 kSPS AD976. An on-chip clock can support a simpler instrument architecture, while selectable internal or external 2.5 V reference options allow the design to balance simplicity against calibration requirements. Use the manufacturer timing diagram to align conversion status with output capture.
Được đề xuất
Communications Receiver
AD976ACRS can serve as the baseband conversion element in communications receivers when the system requires a 16-bit parallel-output ADC at 200 kSPS. Its switched-capacitor implementation and 5 V single-supply operation fit compact analog receiver boards. The converter should follow gain and channel-selection stages so the analog signal remains inside the 0 V to 5 V input range. Because parallel routing consumes board space, place the ADC and acquisition FPGA or controller according to the manufacturer's recommended layout and keep digital output traces away from sensitive analog inputs.
Được đề xuất
Waveform Acquisition
AD976ACRS is well suited to moderate-speed waveform acquisition where 16-bit resolution and 200 kSPS sampling are sufficient. Its parallel output provides direct transfer into capture logic, avoiding the output multiplexing found in lower-pin-count converters. The on-chip clock offers a straightforward starting point for a single-converter design, and the internal or external 2.5 V reference supports both simple and calibratable architectures. Confirm acquisition latency and output timing with the AD976/AD976A datasheet before synchronizing samples to an external event.
Được đề xuất
Precision Feedback Control
AD976ACRS can provide feedback and supervisory measurements in precision control systems that require high-resolution sampling rather than very high throughput. The 16-bit conversion word offers detailed plant-state information, while the 200 kSPS rate is suitable for many servo and positioning loops. Place conditioning circuitry before the ADC to establish signal range and bandwidth, and use the single 5 V supply architecture to simplify distributed controller boards. Verify loop latency, acquisition timing, and noise performance in the complete analog chain.
Được đề xuất
Automated Test Equipment
AD976ACRS fits automated test equipment that evaluates low-frequency or moderate-bandwidth analog nodes and needs repeatable 16-bit samples at 200 kSPS. Its parallel data output can reduce the burden on a shared acquisition bus, while the selectable 2.5 V reference supports controlled measurement conditions. A practical implementation places the converter behind source impedance control, filtering, and settling protection, then captures the output with synchronous logic. Review offset, gain, and reference calibration methods in the manufacturer datasheet for production-test accuracy.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD976ACRS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD976ACRSZ | AD976AARSZ |
|---|---|---|---|
| Package | 28-lead SSOP | 28-lead SSOP | 28-lead SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 16 bits | 16 bits | 16 bits |
| Throughput Rate | 200 kSPS | 200 kSPS | 200 kSPS |
| Supply Voltage | 5 V | 5 V | 5 V |
| Input Range | 0 V to 5 V | 0 V to 5 V | 0 V to 5 V |
| Reference | Internal or external 2.5 V | Internal or external 2.5 V | Internal or external 2.5 V |
| Output Interface | High-speed parallel | High-speed parallel | High-speed parallel |
| Maximum Power Dissipation | 100 mW | 100 mW | 100 mW |
Bảo phân biệt quan trọng
- Doubles the acquisition rate of the original AD976 (vsAD976)
- Maintains the same 28-lead SSOP footprint for close replacement (vsAD976ACRSZ)
- Supports deterministic parallel data transfer (vsAD976AARSZ)
Ghi chú thiết kế
Follow the Analog Devices AD976/AD976A datasheet layout guidance when placing decoupling, reference, analog-input, clock, and parallel-output connections. Keep analog input routing short and place the input network near the converter to minimize added noise and susceptibility to digital coupling. The 16-bit parallel bus occupies 28-lead SSOP routing resources, so escape it cleanly toward the acquisition logic without introducing long stubs.
Do not substitute the 100 kSPS AD976 for AD976ACRS when the acquisition timing depends on the AD976A family's 200 kSPS throughput. Likewise, distinguish AD976ACRS from AD976ACRSZ by checking package, temperature grade, and lead-free ordering requirements. Use the manufacturer ordering table and pin-description table before releasing a PCB or production BOM.
Decouple the single 5 V supply close to the converter and follow the manufacturer component values and return-path arrangement. Maximum power dissipation is 100 mW, but board-level thermal performance depends on copper area, airflow, and the ambient environment. Use the datasheet power-dissipation equation with the final input voltage, output activity, and ambient temperature before defining the thermal margin.
Treat the 16-bit parallel output as a synchronous digital bus and analyze acquisition timing against the converter's clock and output timing. Keep the output traces short enough to limit propagation delay and loading effects, and account for setup and hold requirements at the receiving device. For higher-speed system architectures, use the manufacturer timing diagrams to determine whether registered capture logic is required.
Thông tin tuân thủ
The AD976ACRS ordering suffix and compliance declarations must be confirmed against the current Analog Devices product documentation. The device is an industrial analog converter and is not identified as an AEC-Q100-qualified automotive part.