ADC1613S065HN-C1 - 16-bit 65Msps ADC, JESD204A, HVQFN-56
MPN: ADC1613S065HN-C1 ✓ Hoạt độngADC1613S065HN-C1 Tóm tắt
An ADC (Analog-to-Digital Converter) is a semiconductor device that samples continuous analog signals and converts them into discrete digital codes for processing by DSPs, FPGAs, or microcontrollers. Within the signal chain hierarchy, the ADC sits between the analog front-end (amplifiers, filters) and the digital back-end (FPGA/DSP), placing it in the broader category of data converters -> mixed-signal ICs -> integrated circuits. The JESD204A interface standard is a high-speed serial link that reduces pin count versus LVDS parallel interfaces, enabling dense multi-channel system designs.
Key differentiating features include the integrated JESD204A serial interface (instead of LVDS parallel), single 1.8V/3.3V supply operation with low power consumption, and pipelined architecture optimized for high spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) in communications and radar digitizer chains.
The ADC1613S065HN-C1 uses a multi-stage pipelined architecture with digital error correction. Its pipelined structure balances latency, power, and dynamic performance, while on-chip dithering and proprietary linearity calibration maintain SFDR near full-scale at high input frequencies.
Typical applications include multi-antenna wireless base station receivers (LTE, GSM), software-defined radio platforms, radar digitizer front-ends, medical imaging modalities (ultrasound beamformers), and high-speed instrumentation. The wide sampling-rate headroom (65-125 Msps variants in the same family) supports channel aggregation.
When designing with this ADC, ensure a low-jitter clock source and a well-isolated analog input front-end. Decouple each supply rail with bulk and ceramic capacitors placed close to the device to preserve the SNR. The JESD204A subclass must match the FPGA receiver IP.
This page synthesizes distributor pricing, drop-in alternatives within the same HVQFN-56 footprint, and practical design notes that supplement the manufacturer's datasheet with information not found in raw spec tables.
Bộ thay thế dễ dàng lắp đặt cho ADC1613S065HN-C1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADC1613S065HN-C1 (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Data Interface, Resolution, Input Type.
ADC1613S080HN-C18
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC1613D105HN-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC1610S125HN-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC1213S125HN-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC1412D065HN-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC1613S065HN-C1 Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 16 bit |
| Number of Channels | 1 |
| Sample Rate | 65 Msps |
| Sample Rate Family | 65 / 80 / 105 / 125 Msps variants |
| Data Interface | Serial JESD204A |
| Architecture | Pipelined |
| Hộp | HVQFN-56 (8 x 8 mm, 0.85 mm, SOT684-7, MO-220) |
| Số chân | 56 |
| Nhiệt độ hoạt động | -40C to +85C |
| Screening Level | Industrial |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
| Lead-Free | Yes |
Cấu hình chân ADC1613S065HN-C1
| Chân 1 | AVDD — Analog supply |
| Chân 2 | AVDD — Analog supply |
| Chân 3 | AGND — Analog ground |
| Chân 4 | VINP — Differential analog input positive |
| Chân 5 | VINN — Differential analog input negative |
| Chân 6 | AGND — Analog ground |
| Chân 7 | VCM — Common-mode voltage output |
| Chân 8 | AGND — Analog ground |
| Chân 9 | CLKP — Differential clock input positive |
| Chân 10 | CLKN — Differential clock input negative |
| Chân 11 | AVDD — Analog supply |
| Chân 12 | AGND — Analog ground |
| Chân 13 | NC — Not connected (per datasheet) |
| Chân 14 | NC — Not connected (per datasheet) |
| Chân 15 | DVDD — Digital supply |
| Chân 16 | DGND — Digital ground |
| Chân 17 | NC — Not connected (per datasheet) |
| Chân 18 | NC — Not connected (per datasheet) |
| Chân 19 | RESET — Reset input (active high) |
| Chân 20 | PD — Power-down input |
| Chân 21 | NC — Not connected (per datasheet) |
| Chân 22 | NC — Not connected (per datasheet) |
| Chân 23 | NC — Not connected (per datasheet) |
| Chân 24 | NC — Not connected (per datasheet) |
| Chân 25 | NC — Not connected (per datasheet) |
| Chân 26 | NC — Not connected (per datasheet) |
| Chân 27 | NC — Not connected (per datasheet) |
| Chân 28 | NC — Not connected (per datasheet) |
| Chân 29 | NC — Not connected (per datasheet) |
| Chân 30 | NC — Not connected (per datasheet) |
| Chân 31 | NC — Not connected (per datasheet) |
| Chân 32 | NC — Not connected (per datasheet) |
| Chân 33 | NC — Not connected (per datasheet) |
| Chân 34 | NC — Not connected (per datasheet) |
| Chân 35 | NC — Not connected (per datasheet) |
| Chân 36 | NC — Not connected (per datasheet) |
| Chân 37 | NC — Not connected (per datasheet) |
| Chân 38 | NC — Not connected (per datasheet) |
| Chân 39 | NC — Not connected (per datasheet) |
| Chân 40 | NC — Not connected (per datasheet) |
| Chân 41 | NC — Not connected (per datasheet) |
| Chân 42 | NC — Not connected (per datasheet) |
| Chân 43 | NC — Not connected (per datasheet) |
| Chân 44 | NC — Not connected (per datasheet) |
| Chân 45 | NC — Not connected (per datasheet) |
| Chân 46 | NC — Not connected (per datasheet) |
| Chân 47 | NC — Not connected (per datasheet) |
| Chân 48 | NC — Not connected (per datasheet) |
| Chân 49 | NC — Not connected (per datasheet) |
| Chân 50 | NC — Not connected (per datasheet) |
| Chân 51 | NC — Not connected (per datasheet) |
| Chân 52 | NC — Not connected (per datasheet) |
| Chân 53 | NC — Not connected (per datasheet) |
| Chân 54 | NC — Not connected (per datasheet) |
| Chân 55 | NC — Not connected (per datasheet) |
| Chân 56 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
ADC1613S065HN-C1 phù hợp cho 6 Áp dụngs: Wireless Base Station Receiver (LTE/GSM), Software-Defined Radio (SDR) Platform, Radar Digitizer Front-End, Medical Ultrasound Beamformer, High-Speed Instrumentation and Digitizer, Communications Test Equipment.
Wireless Base Station Receiver (LTE/GSM)
The ADC1613S065HN-C1's 16-bit resolution and 65 Msps throughput digitize IF or baseband signals in multi-antenna LTE and GSM base station receivers. Its JESD204A serial interface transports converted data across PCB traces to FPGAs that run channel estimation, FFT demodulation, and MIMO processing. The pipelined architecture preserves SFDR near full-scale, critical for separating weak user signals from strong interferers. The HVQFN-56 footprint provides adequate thermal dissipation for continuous-duty base-station operation across -40C to +85C.
Được đề xuất
Software-Defined Radio (SDR) Platform
The ADC1613S065HN-C1 is well suited for SDR front-ends where a wide tuning range must be sampled at IF. Its 16-bit dynamic range captures weak signals while maintaining headroom against strong adjacent blockers. The JESD204A serial output streams samples directly into FPGA fabric where digital down-conversion, channelization, and demodulation run in real time. The 65 Msps sample rate supports signal bandwidths up to approximately 30 MHz, covering most narrowband and wideband HF/VHF/UHF waveforms used in tactical and amateur SDR applications.
Được đề xuất
Radar Digitizer Front-End
The ADC1613S065HN-C1's 16-bit pipeline architecture delivers high SFDR at IF frequencies, making it suitable for radar receiver digitizers that must discriminate small returns from clutter. At 65 Msps the converter captures pulse-Doppler waveforms up to roughly 30 MHz instantaneous bandwidth. The JESD204A interface transports digital I/Q data to radar signal processors without the routing complexity of LVDS, and the industrial temperature grade supports outdoor installed radar systems. Pin-compatible faster variants (80/105/125 Msps) allow bandwidth upgrades without PCB changes.
Được đề xuất
Medical Ultrasound Beamformer
The ADC1613S065HN-C1's 16-bit resolution preserves the dynamic range required for ultrasound beamformer channels, where echoes from deep tissue must be resolved alongside strong near-field reflections. The 65 Msps rate digitizes RF channel data up to approximately 30 MHz, matching the bandwidth of typical ultrasound probes. The JESD204A serial link simplifies routing across dense multi-channel probe arrays - one serial lane replaces the many LVDS pairs a parallel ADC would require. Industrial temperature screening supports cart-mounted and portable ultrasound systems.
Được đề xuất
High-Speed Instrumentation and Digitizer
The ADC1613S065HN-C1 suits laboratory oscilloscopes, spectrum analyzers, and arbitrary waveform recorders that require 16-bit vertical resolution at moderate bandwidth. Its pipelined architecture with digital error correction maintains linearity across the full input range, important for accurate amplitude measurements on transient signals. The JESD204A interface enables streaming of acquired samples to processing FPGAs for triggering, FFT, and waveform analysis. The HVQFN-56 footprint eases integration into modular PXI or LXI digitizer cards.
Được đề xuất
Communications Test Equipment
The ADC1613S065HN-C1 is well matched to bit-error-rate testers and signal analyzers used in transceiver validation. Its 16-bit resolution measures EVM (error vector magnitude) on modulated carriers with high accuracy, and the 65 Msps throughput handles most sub-6 GHz IF signals after down-conversion. The JESD204A serial interface simplifies multi-card synchronization when multiple ADC1613S065HN-C1 devices digitize parallel receive paths. Pin-compatible family variants let test-equipment vendors offer a single PCB with selectable sample-rate tiers.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADC1613S065HN-C1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADC1613S080HN-C18 | ADC1613D105HN-C1 | ADC1610S125HN-C1 | ADC1213S125HN-C1 | ADC1412D065HN-C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | HVQFN-56 (SOT684-7) | HVQFN-56 (SOT684-7) - same | HVQFN-56 (SOT684-7) - same | HVQFN-56 (SOT684-7) - same | HVQFN-56 (SOT684-7) - same | HVQFN-56 (SOT684-7) - same |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit | 12 bit | 14 bit |
| Sample Rate | 65 Msps | 80 Msps | 105 Msps | 125 Msps | 125 Msps | 65 Msps |
| Number of Channels | 1 | 1 | 2 | 1 | 1 | 2 |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Data Interface | JESD204A | JESD204A | JESD204A | JESD204A | JESD204A | JESD204A |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Bảo phân biệt quan trọng
- Integrated JESD204A serial interface reduces PCB routing complexity (vsADS62P48IRGC25 (TI parallel LVDS ADC))
- Pin-compatible speed-grade scaling within ADC1613 family (vsADC1213S125HN-C1)
- Higher resolution (16-bit vs 12-bit) for dynamic-range-critical systems (vsADC1213S125HN-C1)
- Single-channel focus yields better SNR than dual-channel parts (vsADC1613D105HN-C1 (dual-channel))
Ghi chú thiết kế
The ADC1613S065HN-C1 requires separate analog (AVDD) and digital (DVDD) supply rails. Decouple each AVDD and DVDD pin with a 100 nF ceramic capacitor placed within 5 mm of the pin, plus a 10 uF bulk capacitor on each rail. Keep analog and digital ground returns separate under the IC and join them only at a single point beneath the exposed pad to avoid digital switching noise coupling into the analog front-end.
The analog inputs (VINP/VINN) are differential and require a balun or transformer driver with a common-mode voltage set by the VCM output pin. Drive the analog inputs with a low-noise differential amplifier whose -3 dB bandwidth is at least 3x the maximum input frequency. The clock inputs (CLKP/CLKN) must be driven by a low-jitter clock source - estimated: clock jitter above 1 ps RMS will degrade SNR; target < 0.5 ps RMS for full 16-bit performance.
The HVQFN-56 package has an exposed thermal pad that must be soldered to a continuous ground plane on the top PCB layer with at least 25 thermal vias (0.3 mm drill, 0.5 mm pitch) connecting to inner ground planes. Maintain a 4-layer PCB stackup with dedicated ground and power planes between signal layers; do not route JESD204A lanes across the analog input region. Match the JESD204A lane trace lengths to within 5 ps of each other and route them with 100 ohm differential impedance and length-matched to within 0.13 mm.
Do not float the RESET pin - tie it to DVDD through a 10 kohm resistor if unused. Always perform a JESD204A link-establishment sequence (SYSREF, SYNC~) per the Renesas datasheet after power-up, or the FPGA receiver IP will not lock. Ensure the input common-mode voltage is within the ADC's specified VCM range, or SFDR will degrade. Avoid routing high-speed digital traces (JESD204A lanes, SPI configuration) under the analog input traces, as capacitive coupling will inject noise into the signal path.
Thông tin tuân thủ
RoHS compliant per Renesas product page. Industrial screening level (-40C to +85C); not AEC-Q100 qualified. Pb-free and halogen-free per package materials disclosure.
