ADM3070EYRZ - 3.3V 250kbps RS-485/RS-422 | Analog Devices
MPN: ADM3070EYRZ ✓ Hoạt độngADM3070EYRZ Tóm tắt
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable data transmission over long, noisy cables. RS-422 supports point-to-point balanced links, while RS-485 permits multiple drivers and receivers on a shared bus when the system is configured correctly. The ADM3070EYRZ belongs to the transceiver hierarchy of interface ICs used in industrial automation, building controls, instrumentation, and data acquisition.
Key features include a 3.3 V supply, operation at data rates up to 250 kbps, ±15 kV ESD protection, full-duplex operation, and support for up to 256 nodes on the bus. True fail-safe receiver behavior helps maintain a defined output when the bus is idle, externally shorted, or open. Its eighth-load capability allows multiple transceivers to share a bus without exceeding its permitted loading.
The device combines separate transmit and receive paths for full-duplex communication. Differential signaling improves common-mode rejection and helps preserve data integrity across industrial environments. The transceiver architecture is intended for TIA/EIA RS-485 and RS-422 systems operating from a single 3.3 V rail, making it suitable for equipment that needs compact, protected balanced communication without a separate line driver and receiver.
Typical applications include industrial motor controllers, programmable logic controller interfaces, factory data acquisition, building automation, instrumentation, and embedded serial networks. Full duplex allows simultaneous command transmission and status reception, which is useful in closed-loop control systems where host commands and sensor feedback must not share the same signal pair.
PCB design should provide a continuous return path beneath the board traces, route the differential pair as a closely coupled pair, and place protection and bypass components near connector entry points. Verify the termination strategy for each RS-422 or RS-485 network because improper termination can reduce signal quality or increase loading.
This page combines the manufacturer's device characteristics, verified product information, package details, interface-selection guidance, and practical PCB considerations to support component evaluation and board-level implementation.
Bộ thay thế dễ dàng lắp đặt cho ADM3070EYRZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM3070EYRZ (cùng hình factor và footprint) — khác nhau ở ESD Protection, Maximum Data Rate, Package, Product Type.
ADM3070EARZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM3070EYRZ-REEL7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM3070EARZ-REEL7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN65HVD73D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SP3070EEN-L/TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM3070EYRZ Thông số kỹ thuật
| Product Type | Full-duplex RS-485/RS-422 transceiver |
| Điện áp cung cấp | 3.3 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV on RS-485 input and output pins |
| Duplex Mode | Full duplex |
| Bus Standards | TIA/EIA RS-485 and RS-422 |
| Load Capability | One-eighth unit load |
| Maximum Nodes | 256 nodes |
| Receiver Type | True fail-safe receiver |
| Driver and Receiver Control | DE and RE control inputs |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Khoảng nhiệt độ hoạt động | -40°C to +125°C |
| Manufacturer Lifecycle Status | Production |
Hướng dẫn cấu hình chân ADM3070EYRZ 14-pin soic
Cấu hình chân cho ADM3070EYRZ (14-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM3070EYRZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM3070EYRZ phù hợp cho 6 Áp dụngs: Industrial PLC Communication, Motor Controller Feedback, Building Automation Networks, Factory Data Acquisition, Instrumentation and Test Equipment, Robotics and Machine Communication.
Industrial PLC Communication
The ADM3070EYRZ fits industrial PLC communication links that exchange commands and status over balanced copper cabling. Its 250 kbps data rate supports responsive control traffic without the complexity of a high-speed transceiver, while ±15 kV ESD protection strengthens the interface against electrostatic discharge at industrial connection points. The true fail-safe receiver inputs also help produce predictable logic states when a cable is disconnected or the bus enters a fault condition. In a PLC design, the transceiver can connect a 3.3 V controller to an RS-485 or RS-422 field bus, with DE and RE pins managed by the controller firmware.
Được đề xuất
Motor Controller Feedback
The ADM3070EYRZ is well suited to motor-controller feedback paths where a control processor needs to transmit commands and receive position, current, or status information simultaneously. Full-duplex operation separates the transmit and receive channels, avoiding time-sharing one RS-485 pair and improving deterministic control-loop communication. The 3.3 V supply supports compact embedded controllers, and the 250 kbps rate is appropriate for supervisory feedback rather than high-frequency encoder data delivered by a dedicated interface. Use separate differential pairs for each direction and route them as controlled PCB or shielded cable connections.
Được đề xuất
Building Automation Networks
The ADM3070EYRZ supports building automation modules that communicate with sensors, controllers, and remote field equipment over RS-485 or RS-422. Its one-eighth-load implementation permits up to 256 nodes according to the manufacturer documentation, making it useful for multi-zone building networks. The ±15 kV ESD protection is valuable around long cables and user-accessible equipment, while true fail-safe receiver inputs improve behavior during wiring faults. A building-control gateway can use the transceiver's full-duplex mode for separate command and status buses.
Được đề xuất
Factory Data Acquisition
The ADM3070EYRZ is appropriate for factory data-acquisition equipment gathering measurements from multiple remote sensor nodes. The 250 kbps rate accommodates supervisory telemetry while one-eighth-load operation supports a larger node count than a unit-load transceiver. True fail-safe receiver behavior helps a master distinguish an inactive line from an uncertain fault state, and the protected RS-485 pins suit cabling routed near industrial machinery. Use the full-duplex configuration when acquisition and command traffic require independent differential pairs.
Được đề xuất
Instrumentation and Test Equipment
The ADM3070EYRZ can connect laboratory and industrial instrumentation to remote fixtures through a protected balanced interface. Its 3.3 V operation reduces supply complexity in compact instruments, and the 250 kbps maximum data rate is suitable for command, status, and moderate measurement-data traffic. ESD protection reduces susceptibility to discharge encountered when test leads are connected or disconnected. In a portable tester, full-duplex communication allows the instrument to issue commands and continuously return measurements over separate RS-422 pairs.
Được đề xuất
Robotics and Machine Communication
The ADM3070EYRZ fits robot controllers, machine vision stations, and production cells that need dependable command exchange over industrial wiring. Its full-duplex configuration supports simultaneous control commands and status reporting, while the 250 kbps rate is appropriate for supervisory communication between robotic subsystems. The ±15 kV ESD protection is useful around frequently serviced equipment and cable connectors, and the 14-pin SOIC simplifies assembly. In a robot cell, the interface can bridge a 3.3 V controller to remote actuators or sensors without using separate transmit-only and receive-only interface devices.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM3070EYRZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM3070EARZ | ADM3070EYRZ-REEL7 | ADM3070EARZ-REEL7 | SN65HVD73D | SP3070EEN-L/TR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Texas Instruments | Diodes Incorporated |
| Product Function | Full-duplex RS-485/RS-422 transceiver | ADM3070E family RS-485/RS-422 transceiver | Full-duplex RS-485/RS-422 transceiver | ADM3070E family RS-485/RS-422 transceiver | RS-485 transceiver | RS-485 transceiver |
Bảo phân biệt quan trọng
- Full-duplex RS-485 and RS-422 operation (vsSN65HVD73D)
- High node-count bus support (vsSP3070EEN-L/TR)
- Documented high-level ESD protection (vsSN65HVD73D)
- True fail-safe receiver behavior (vsSP3070EEN-L/TR)
Ghi chú thiết kế
Route each RS-485 or RS-422 differential pair with matched spacing and minimal length mismatch. Keep the driver-side and receiver-side pairs physically separated where practical to reduce crosstalk and maintain a clean return path. Place the transceiver close to the board connector, with external protection and filtering ahead of the IC rather than between the connector and signal traces.
Do not assume that equal SOIC packages guarantee electrical interchangeability. Before replacing the ADM3070EYRZ with SN65HVD73D, SP3070EEN-L/TR, or another candidate, compare DE and RE pin functions, driver-enable polarity, receiver-fail-safe thresholds, bus loading, maximum data rate, and termination behavior. A footprint fit check alone is insufficient for a reliable drop-in decision.
Use a continuous ground reference beneath the transceiver and route high-current or switching-node returns away from the differential pair. Add supply bypassing at the device pins and provide local high-frequency return paths for transceiver currents. If the cable leaves the enclosure, place the protection network at the connector and keep the protected trace separated from sensitive internal circuitry.
The ADM3070EYRZ operates from a 3.3 V supply, so confirm that every rail connected to the interface meets the device's specified limits. Provide local decoupling close to the supply pins and avoid sharing a narrow return path with unrelated switching loads. A stable low-impedance supply reference improves signal integrity and helps prevent transient perturbations from coupling into the receiver.
Thông tin tuân thủ
The product information identifies the ADM3070E family as production and lists TIA/EIA RS-485 and RS-422 compliance. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not present in the available product data.