ADM3070EYRZ - 3.3V 250kbps RS-485/RS-422 | Analog Devices
MPN: ADM3070EYRZ ✓ NakahandaADM3070EYRZ Ulas
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable data transmission over long, noisy cables. RS-422 supports point-to-point balanced links, while RS-485 permits multiple drivers and receivers on a shared bus when the system is configured correctly. The ADM3070EYRZ belongs to the transceiver hierarchy of interface ICs used in industrial automation, building controls, instrumentation, and data acquisition.
Key features include a 3.3 V supply, operation at data rates up to 250 kbps, ±15 kV ESD protection, full-duplex operation, and support for up to 256 nodes on the bus. True fail-safe receiver behavior helps maintain a defined output when the bus is idle, externally shorted, or open. Its eighth-load capability allows multiple transceivers to share a bus without exceeding its permitted loading.
The device combines separate transmit and receive paths for full-duplex communication. Differential signaling improves common-mode rejection and helps preserve data integrity across industrial environments. The transceiver architecture is intended for TIA/EIA RS-485 and RS-422 systems operating from a single 3.3 V rail, making it suitable for equipment that needs compact, protected balanced communication without a separate line driver and receiver.
Typical applications include industrial motor controllers, programmable logic controller interfaces, factory data acquisition, building automation, instrumentation, and embedded serial networks. Full duplex allows simultaneous command transmission and status reception, which is useful in closed-loop control systems where host commands and sensor feedback must not share the same signal pair.
PCB design should provide a continuous return path beneath the board traces, route the differential pair as a closely coupled pair, and place protection and bypass components near connector entry points. Verify the termination strategy for each RS-422 or RS-485 network because improper termination can reduce signal quality or increase loading.
This page combines the manufacturer's device characteristics, verified product information, package details, interface-selection guidance, and practical PCB considerations to support component evaluation and board-level implementation.
Mga alternatibo na pwedeng ilagay na ADM3070EYRZ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ADM3070EYRZ (parehas na form factor at footprint) — pagkakaiba sa ESD Protection, Maximum Data Rate, Package, Product Type.
ADM3070EARZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADM3070EYRZ-REEL7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADM3070EARZ-REEL7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
SN65HVD73D
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →SP3070EEN-L/TR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADM3070EYRZ Mga Spesipikasyon
| Product Type | Full-duplex RS-485/RS-422 transceiver |
| Volte ng Pagbibigay | 3.3 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV on RS-485 input and output pins |
| Duplex Mode | Full duplex |
| Bus Standards | TIA/EIA RS-485 and RS-422 |
| Load Capability | One-eighth unit load |
| Maximum Nodes | 256 nodes |
| Receiver Type | True fail-safe receiver |
| Driver and Receiver Control | DE and RE control inputs |
| Packhaging | 14-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Hanay ng Temperature na Operasyon | -40°C to +125°C |
| Manufacturer Lifecycle Status | Production |
Gabay sa Pin Configuration ng ADM3070EYRZ 14-pin soic
Pin configuration para sa ADM3070EYRZ (14-pin soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ADM3070EYRZ.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADM3070EYRZ ay nararapat para sa 6 aplikasyons: Industrial PLC Communication, Motor Controller Feedback, Building Automation Networks, Factory Data Acquisition, Instrumentation and Test Equipment, Robotics and Machine Communication.
Industrial PLC Communication
The ADM3070EYRZ fits industrial PLC communication links that exchange commands and status over balanced copper cabling. Its 250 kbps data rate supports responsive control traffic without the complexity of a high-speed transceiver, while ±15 kV ESD protection strengthens the interface against electrostatic discharge at industrial connection points. The true fail-safe receiver inputs also help produce predictable logic states when a cable is disconnected or the bus enters a fault condition. In a PLC design, the transceiver can connect a 3.3 V controller to an RS-485 or RS-422 field bus, with DE and RE pins managed by the controller firmware.
Inirekomenda
Motor Controller Feedback
The ADM3070EYRZ is well suited to motor-controller feedback paths where a control processor needs to transmit commands and receive position, current, or status information simultaneously. Full-duplex operation separates the transmit and receive channels, avoiding time-sharing one RS-485 pair and improving deterministic control-loop communication. The 3.3 V supply supports compact embedded controllers, and the 250 kbps rate is appropriate for supervisory feedback rather than high-frequency encoder data delivered by a dedicated interface. Use separate differential pairs for each direction and route them as controlled PCB or shielded cable connections.
Inirekomenda
Building Automation Networks
The ADM3070EYRZ supports building automation modules that communicate with sensors, controllers, and remote field equipment over RS-485 or RS-422. Its one-eighth-load implementation permits up to 256 nodes according to the manufacturer documentation, making it useful for multi-zone building networks. The ±15 kV ESD protection is valuable around long cables and user-accessible equipment, while true fail-safe receiver inputs improve behavior during wiring faults. A building-control gateway can use the transceiver's full-duplex mode for separate command and status buses.
Inirekomenda
Factory Data Acquisition
The ADM3070EYRZ is appropriate for factory data-acquisition equipment gathering measurements from multiple remote sensor nodes. The 250 kbps rate accommodates supervisory telemetry while one-eighth-load operation supports a larger node count than a unit-load transceiver. True fail-safe receiver behavior helps a master distinguish an inactive line from an uncertain fault state, and the protected RS-485 pins suit cabling routed near industrial machinery. Use the full-duplex configuration when acquisition and command traffic require independent differential pairs.
Inirekomenda
Instrumentation and Test Equipment
The ADM3070EYRZ can connect laboratory and industrial instrumentation to remote fixtures through a protected balanced interface. Its 3.3 V operation reduces supply complexity in compact instruments, and the 250 kbps maximum data rate is suitable for command, status, and moderate measurement-data traffic. ESD protection reduces susceptibility to discharge encountered when test leads are connected or disconnected. In a portable tester, full-duplex communication allows the instrument to issue commands and continuously return measurements over separate RS-422 pairs.
Inirekomenda
Robotics and Machine Communication
The ADM3070EYRZ fits robot controllers, machine vision stations, and production cells that need dependable command exchange over industrial wiring. Its full-duplex configuration supports simultaneous control commands and status reporting, while the 250 kbps rate is appropriate for supervisory communication between robotic subsystems. The ±15 kV ESD protection is useful around frequently serviced equipment and cable connectors, and the 14-pin SOIC simplifies assembly. In a robot cell, the interface can bridge a 3.3 V controller to remote actuators or sensors without using separate transmit-only and receive-only interface devices.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADM3070EYRZ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADM3070EARZ | ADM3070EYRZ-REEL7 | ADM3070EARZ-REEL7 | SN65HVD73D | SP3070EEN-L/TR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Texas Instruments | Diodes Incorporated |
| Product Function | Full-duplex RS-485/RS-422 transceiver | ADM3070E family RS-485/RS-422 transceiver | Full-duplex RS-485/RS-422 transceiver | ADM3070E family RS-485/RS-422 transceiver | RS-485 transceiver | RS-485 transceiver |
Pangunahing mga Pagkakaiba
- Full-duplex RS-485 and RS-422 operation (kumpara saSN65HVD73D)
- High node-count bus support (kumpara saSP3070EEN-L/TR)
- Documented high-level ESD protection (kumpara saSN65HVD73D)
- True fail-safe receiver behavior (kumpara saSP3070EEN-L/TR)
Talaan ng Disenyo
Route each RS-485 or RS-422 differential pair with matched spacing and minimal length mismatch. Keep the driver-side and receiver-side pairs physically separated where practical to reduce crosstalk and maintain a clean return path. Place the transceiver close to the board connector, with external protection and filtering ahead of the IC rather than between the connector and signal traces.
Do not assume that equal SOIC packages guarantee electrical interchangeability. Before replacing the ADM3070EYRZ with SN65HVD73D, SP3070EEN-L/TR, or another candidate, compare DE and RE pin functions, driver-enable polarity, receiver-fail-safe thresholds, bus loading, maximum data rate, and termination behavior. A footprint fit check alone is insufficient for a reliable drop-in decision.
Use a continuous ground reference beneath the transceiver and route high-current or switching-node returns away from the differential pair. Add supply bypassing at the device pins and provide local high-frequency return paths for transceiver currents. If the cable leaves the enclosure, place the protection network at the connector and keep the protected trace separated from sensitive internal circuitry.
The ADM3070EYRZ operates from a 3.3 V supply, so confirm that every rail connected to the interface meets the device's specified limits. Provide local decoupling close to the supply pins and avoid sharing a narrow return path with unrelated switching loads. A stable low-impedance supply reference improves signal integrity and helps prevent transient perturbations from coupling into the receiver.
Impormasyon ng Pagsunod sa Kautusan
The product information identifies the ADM3070E family as production and lists TIA/EIA RS-485 and RS-422 compliance. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not present in the available product data.