Analog Devices

ADM3070EYRZ - 3.3V 250kbps RS-485/RS-422 | Analog Devices

料号: ADM3070EYRZ ✓ 量产中
3.3 V Vdss TIA/EIA RS-485 and RS-422 Rds(on) 14-pin SOIC Package
最小起订量: 1 |

ADM3070EYRZ 概述

The Analog Devices ADM3070EYRZ is a 3.3 V, 250 kbps, full-duplex RS-485/RS-422 interface transceiver with ±15 kV ESD protection on its RS-485 input and output pins. It supports one-eighth-unit-load operation, provides true fail-safe receiver inputs, and is packaged in a 14-pin SOIC for industrial communication equipment.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable data transmission over long, noisy cables. RS-422 supports point-to-point balanced links, while RS-485 permits multiple drivers and receivers on a shared bus when the system is configured correctly. The ADM3070EYRZ belongs to the transceiver hierarchy of interface ICs used in industrial automation, building controls, instrumentation, and data acquisition.

Key features include a 3.3 V supply, operation at data rates up to 250 kbps, ±15 kV ESD protection, full-duplex operation, and support for up to 256 nodes on the bus. True fail-safe receiver behavior helps maintain a defined output when the bus is idle, externally shorted, or open. Its eighth-load capability allows multiple transceivers to share a bus without exceeding its permitted loading.

The device combines separate transmit and receive paths for full-duplex communication. Differential signaling improves common-mode rejection and helps preserve data integrity across industrial environments. The transceiver architecture is intended for TIA/EIA RS-485 and RS-422 systems operating from a single 3.3 V rail, making it suitable for equipment that needs compact, protected balanced communication without a separate line driver and receiver.

Typical applications include industrial motor controllers, programmable logic controller interfaces, factory data acquisition, building automation, instrumentation, and embedded serial networks. Full duplex allows simultaneous command transmission and status reception, which is useful in closed-loop control systems where host commands and sensor feedback must not share the same signal pair.

PCB design should provide a continuous return path beneath the board traces, route the differential pair as a closely coupled pair, and place protection and bypass components near connector entry points. Verify the termination strategy for each RS-422 or RS-485 network because improper termination can reduce signal quality or increase loading.

This page combines the manufacturer's device characteristics, verified product information, package details, interface-selection guidance, and practical PCB considerations to support component evaluation and board-level implementation.

直接替换替代料: ADM3070EYRZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ADM3070EYRZ (相同外形与封装尺寸) ——差异在于 ESD Protection, Maximum Data Rate, Package, Product Type.

Texas Instruments
ESD Protection: ±12 kV IEC
Maximum Data Rate: 20 Mbps
Package: 14-pin SOIC (D)
对比 ADM3070EYRZ →

ADM3070EARZ

✅ 直接替换
📦 14-pin SOIC
Same documented ADM3070E family and 14-pin SOIC format; the visible comparison does not quantify the ordering-code or temperature-range difference.

📋 参考替代料(不在目录中)

ADM3070EYRZ-REEL7

✅ 直接替换
📦 14-pin SOIC
Same ADM3070EYRZ electrical device and 14-pin SOIC footprint, with a reel ordering suffix rather than a different electrical configuration.

📋 参考替代料(不在目录中)

ADM3070EARZ-REEL7

✅ 直接替换
📦 14-pin SOIC
Same documented ADM3070E family and 14-pin SOIC format; reel suffix changes packing, while the exact electrical ordering-code differences are not quantified.

📋 参考替代料(不在目录中)

SN65HVD73D

✅ 直接替换
Texas Instruments
📦 14-pin SOIC
RS-485/RS-422 Full-Duplex Transceiver · 3 V to 3.6 V · 3.3 V · 20 Mbps · ±12 kV IEC · 1 · 1 · Full Duplex

联系询价

查看数据手册 →

SP3070EEN-L/TR

✅ 直接替换
📦 14-pin SOIC
The comparison result identifies an RS-485 alternative, but its package listing does not establish a 14-pin SOIC footprint or quantified pin compatibility.

📋 参考替代料(不在目录中)

ADM3070EYRZ 规格参数

Product Type Full-duplex RS-485/RS-422 transceiver
电源电压 3.3 V
Maximum Data Rate 250 kbps
ESD Protection ±15 kV on RS-485 input and output pins
Duplex Mode Full duplex
Bus Standards TIA/EIA RS-485 and RS-422
Load Capability One-eighth unit load
Maximum Nodes 256 nodes
Receiver Type True fail-safe receiver
Driver and Receiver Control DE and RE control inputs
封装 14-pin SOIC
安装类型 Surface mount
工作温度范围 -40°C to +125°C
Manufacturer Lifecycle Status Production

ADM3070EYRZ 14-pin soic 引脚配置指南

ADM3070EYRZ(14-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ADM3070EYRZ 的 14-pin soic 封装引脚图

暂无详细引脚数据: ADM3070EYRZ.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADM3070EYRZ 适用于 6 应用s: Industrial PLC Communication, Motor Controller Feedback, Building Automation Networks, Factory Data Acquisition, Instrumentation and Test Equipment, Robotics and Machine Communication.

🏭

Industrial PLC Communication

The ADM3070EYRZ fits industrial PLC communication links that exchange commands and status over balanced copper cabling. Its 250 kbps data rate supports responsive control traffic without the complexity of a high-speed transceiver, while ±15 kV ESD protection strengthens the interface against electrostatic discharge at industrial connection points. The true fail-safe receiver inputs also help produce predictable logic states when a cable is disconnected or the bus enters a fault condition. In a PLC design, the transceiver can connect a 3.3 V controller to an RS-485 or RS-422 field bus, with DE and RE pins managed by the controller firmware.

🔧

Motor Controller Feedback

The ADM3070EYRZ is well suited to motor-controller feedback paths where a control processor needs to transmit commands and receive position, current, or status information simultaneously. Full-duplex operation separates the transmit and receive channels, avoiding time-sharing one RS-485 pair and improving deterministic control-loop communication. The 3.3 V supply supports compact embedded controllers, and the 250 kbps rate is appropriate for supervisory feedback rather than high-frequency encoder data delivered by a dedicated interface. Use separate differential pairs for each direction and route them as controlled PCB or shielded cable connections.

🏠

Building Automation Networks

The ADM3070EYRZ supports building automation modules that communicate with sensors, controllers, and remote field equipment over RS-485 or RS-422. Its one-eighth-load implementation permits up to 256 nodes according to the manufacturer documentation, making it useful for multi-zone building networks. The ±15 kV ESD protection is valuable around long cables and user-accessible equipment, while true fail-safe receiver inputs improve behavior during wiring faults. A building-control gateway can use the transceiver's full-duplex mode for separate command and status buses.

📊

Factory Data Acquisition

The ADM3070EYRZ is appropriate for factory data-acquisition equipment gathering measurements from multiple remote sensor nodes. The 250 kbps rate accommodates supervisory telemetry while one-eighth-load operation supports a larger node count than a unit-load transceiver. True fail-safe receiver behavior helps a master distinguish an inactive line from an uncertain fault state, and the protected RS-485 pins suit cabling routed near industrial machinery. Use the full-duplex configuration when acquisition and command traffic require independent differential pairs.

🔧

Instrumentation and Test Equipment

The ADM3070EYRZ can connect laboratory and industrial instrumentation to remote fixtures through a protected balanced interface. Its 3.3 V operation reduces supply complexity in compact instruments, and the 250 kbps maximum data rate is suitable for command, status, and moderate measurement-data traffic. ESD protection reduces susceptibility to discharge encountered when test leads are connected or disconnected. In a portable tester, full-duplex communication allows the instrument to issue commands and continuously return measurements over separate RS-422 pairs.

🤖

Robotics and Machine Communication

The ADM3070EYRZ fits robot controllers, machine vision stations, and production cells that need dependable command exchange over industrial wiring. Its full-duplex configuration supports simultaneous control commands and status reporting, while the 250 kbps rate is appropriate for supervisory communication between robotic subsystems. The ±15 kV ESD protection is useful around frequently serviced equipment and cable connectors, and the 14-pin SOIC simplifies assembly. In a robot cell, the interface can bridge a 3.3 V controller to remote actuators or sensors without using separate transmit-only and receive-only interface devices.

What is the ADM3070EYRZ?
The ADM3070EYRZ is a 3.3 V, full-duplex RS-485/RS-422 transceiver designed for balanced data communication at rates up to 250 kbps. According to the Analog Devices ADM3070E datasheet, it provides ±15 kV ESD protection on RS-485 input and output pins, true fail-safe receiver inputs, and support for one-eighth-unit-load operation. Its 14-pin SOIC package suits compact industrial-control, automation, instrumentation, and data-acquisition equipment.
What are the key specifications of ADM3070EYRZ that engineers should know?
The principal ADM3070EYRZ specifications are a 3.3 V supply, full-duplex operation, a maximum data rate of 250 kbps, ±15 kV ESD protection, one-eighth-unit-load capability, and support for as many as 256 bus nodes. The Analog Devices ADM3070E datasheet also identifies true fail-safe receiver inputs and separate DE/RE control functions. These characteristics place the device between general-purpose RS-485 transceivers and higher-speed, more specialized interface families.
Where can I download the ADM3070EYRZ datasheet PDF?
The official ADM3070EYRZ datasheet PDF is available from Analog Devices through the ADM3070E product page and the linked manufacturer datasheet. The document covers the 3.3 V supply, 250 kbps operation, ±15 kV ESD protection, half- and full-duplex variants, true fail-safe receivers, up to 256 bus nodes, electrical characteristics, and the −40°C to +125°C operating range. Use the manufacturer document for final pin, limit, and application details.
Where can I find the ADM3070EYRZ pinout?
The ADM3070EYRZ pinout is shown in the pin-configuration diagrams of the official Analog Devices ADM3070E datasheet. The device is a 14-pin SOIC and supports full-duplex RS-485/RS-422 operation with DE and RE control signals. Because the exact physical pin numbering must be matched to the package drawing, use the datasheet pin diagram directly when assigning PCB tracks and checking the exposed connections.
How does the ADM3070EYRZ protect an RS-485 interface?
The ADM3070EYRZ provides ±15 kV ESD protection on its RS-485 input and output pins. According to the Analog Devices ADM3070E datasheet, the device also uses true fail-safe receiver inputs to maintain defined behavior under bus faults such as an idle, shorted, or open line. These protections improve robustness in industrial environments where cables and connectors can accumulate electrostatic discharge.
Is ADM3070EYRZ suitable for industrial automation equipment?
Yes, the ADM3070EYRZ is suitable for industrial automation equipment requiring a protected, balanced communication link. It operates from 3.3 V, supports data rates up to 250 kbps, provides ±15 kV ESD protection, and can accommodate up to 256 nodes with its one-eighth-load design. Its full-duplex configuration is particularly useful where a controller sends commands while simultaneously receiving feedback or sensor data.
What bus can the ADM3070EYRZ communicate on?
The ADM3070EYRZ communicates over TIA/EIA RS-485 or RS-422 balanced buses. RS-422 supports a driver and receiver over a dedicated pair of conductors, while RS-485 can support multiple nodes on a shared bus when driver enable control and network loading are managed correctly. The Analog Devices datasheet specifies up to 256 nodes for the one-eighth-load implementation.
What is the maximum data rate of ADM3070EYRZ?
The maximum data rate of the ADM3070EYRZ is 250 kbps. This makes the transceiver appropriate for moderate-speed industrial links such as controller networks, instrumentation, motor-control feedback, and building automation. The 3.3 V supply and 250 kbps rate distinguish it from lower-rate ADM3070-class variants and from the 500 kbps and 16 Mbps members of the wider ADM307xE family.
What is the difference between ADM3070EYRZ and ADM3070EARZ?
The ADM3070EYRZ and ADM3070EARZ belong to the same ADM3070E device family and are identified in comparison listings as 14-SOIC RS-485/RS-422 transceivers. The visible product information does not establish every ordering-code distinction. Confirm the exact temperature, tape-and-reel, and grade fields against the Analog Devices datasheet and the approved BOM before treating one as a drop-in substitute.
What is the best drop-in replacement for ADM3070EYRZ?
The closest documented drop-in candidate is the ADM3070EARZ because comparison information identifies it in the same ADM3070E family and 14-pin SOIC format. A broader cross-brand choice such as SN65HVD73D must be checked carefully because its DE/RE control arrangement and bus-loading characteristics may differ. Verify pinout, supply voltage, data rate, fail-safe behavior, and termination requirements before substitution.
Can SN65HVD73D replace ADM3070EYRZ?
SN65HVD73D is a 3 V RS-485 transceiver in a 14-pin SOIC, but it should not be assumed to be a direct replacement without a detailed pin-function comparison. The ADM3070EYRZ supports 250 kbps full-duplex RS-485/RS-422 communication, while SN65HVD73D is identified as a 3 V RS-485 transceiver. Check driver-enable polarity, receiver-enable behavior, bus loading, fail-safe thresholds, and footprint compatibility.
When should I choose ADM3070EYRZ over a lower-speed RS-485 transceiver?
Choose the ADM3070EYRZ when the design requires more than basic low-speed RS-485 communication and benefits from its 250 kbps capability, ±15 kV ESD protection, true fail-safe receiver inputs, and one-eighth-load bus implementation. Its full-duplex configuration also allows simultaneous transmit and receive paths. A lower-speed device may be adequate when margin is unnecessary, but it can limit update rate and cable-network flexibility.
Is ADM3070EYRZ the same as ADM3070EARZ?
No, ADM3070EYRZ and ADM3070EARZ are distinct ordering codes within the ADM3070E family. Public comparison data associates both with the 14-SOIC full-duplex RS-485/RS-422 transceiver family, but it does not independently establish whether every electrical and ordering attribute is identical. Compare the exact package code, temperature range, tape-and-reel format, and manufacturer ordering information before treating the parts as interchangeable.
Where can I buy ADM3070EYRZ online?
Use the Request a Quote form on this page to request ADM3070EYRZ availability, current commercial terms, and a firm lead time for the exact ADM3070EYRZ ordering code. The manufacturer product page identifies the ADM3070E as a production device, but stock and delivery schedules can change by quantity and lot. Provide the required quantity, package format, and target date with the request.
What is the lead time for ADM3070EYRZ?
The current lead time for ADM3070EYRZ should be requested through the Request a Quote form on this page using the exact ordering code and required quantity. Analog Devices lists the ADM3070E family as production, but manufacturing schedules, inventory, and quantity breaks are commercial variables. A lead-time confirmation is more reliable than a generic production-status statement for a scheduled build.
Is ADM3070EYRZ in stock?
Current ADM3070EYRZ stock should be confirmed through the Request a Quote form on this page. The product information identifies the ADM3070E family as production and indicates that ADM3070EYRZ is a cataloged 14-SOIC device, but neither statement guarantees immediate inventory for a particular quantity. Include the required quantity and reel or other packing preference when requesting a stock confirmation.

工程参考数据: ADM3070EYRZ ——对比、设计指导和合规信息。

选型指南

Choose the ADM3070EYRZ when a 3.3 V system needs a full-duplex RS-485/RS-422 interface at rates up to 250 kbps, with ±15 kV ESD protection and a documented one-eighth-load capacity for as many as 256 nodes. ADM3070EARZ and its documented reel ordering variants are the closest same-family choices when their exact temperature and packing attributes satisfy the design. Consider SN65HVD73D only after confirming DE/RE behavior, fail-safe thresholds, loading, and termination because its documented product description identifies an RS-485 transceiver rather than the target's complete RS-485/RS-422 feature set. SP3070EEN-L/TR should be treated as a preliminary alternative candidate, not an approved substitution, until its package and pin functions are confirmed. For designs requiring the documented full-duplex interface, ESD rating, and high node count, the ADM3070EYRZ provides the clearest specification match.

与替代料对比

参数 本产品 ADM3070EARZ ADM3070EYRZ-REEL7 ADM3070EARZ-REEL7 SN65HVD73D SP3070EEN-L/TR
Brand Analog Devices Analog Devices Analog Devices Analog Devices Texas Instruments Diodes Incorporated
Product Function Full-duplex RS-485/RS-422 transceiver ADM3070E family RS-485/RS-422 transceiver Full-duplex RS-485/RS-422 transceiver ADM3070E family RS-485/RS-422 transceiver RS-485 transceiver RS-485 transceiver

关键差异点

  • Full-duplex RS-485 and RS-422 operation (对比 SN65HVD73D)
  • High node-count bus support (对比 SP3070EEN-L/TR)
  • Documented high-level ESD protection (对比 SN65HVD73D)
  • True fail-safe receiver behavior (对比 SP3070EEN-L/TR)

设计说明

Route each RS-485 or RS-422 differential pair with matched spacing and minimal length mismatch. Keep the driver-side and receiver-side pairs physically separated where practical to reduce crosstalk and maintain a clean return path. Place the transceiver close to the board connector, with external protection and filtering ahead of the IC rather than between the connector and signal traces.

Do not assume that equal SOIC packages guarantee electrical interchangeability. Before replacing the ADM3070EYRZ with SN65HVD73D, SP3070EEN-L/TR, or another candidate, compare DE and RE pin functions, driver-enable polarity, receiver-fail-safe thresholds, bus loading, maximum data rate, and termination behavior. A footprint fit check alone is insufficient for a reliable drop-in decision.

Use a continuous ground reference beneath the transceiver and route high-current or switching-node returns away from the differential pair. Add supply bypassing at the device pins and provide local high-frequency return paths for transceiver currents. If the cable leaves the enclosure, place the protection network at the connector and keep the protected trace separated from sensitive internal circuitry.

The ADM3070EYRZ operates from a 3.3 V supply, so confirm that every rail connected to the interface meets the device's specified limits. Provide local decoupling close to the supply pins and avoid sharing a narrow return path with unrelated switching loads. A stable low-impedance supply reference improves signal integrity and helps prevent transient perturbations from coupling into the receiver.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The product information identifies the ADM3070E family as production and lists TIA/EIA RS-485 and RS-422 compliance. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not present in the available product data.

数据核验日期: 2026-11-19 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ADM3070EYRZ datasheet ADM3070EYRZ specifications ADM3070EYRZ pinout ADM3070EYRZ datasheet pdf ADM3070EYRZ equivalent ADM3070EYRZ replacement ADM3070EYRZ cross reference ADM3070EYRZ vs SN65HVD73D ADM3070EYRZ 14 SOIC ADM3070EYRZ application circuit Analog Devices ADM3070EYRZ ADM3070EYRZ price ADM3070EYRZ stock

相关元器件 & 术语

Analog Devices ADM3070EYRZ ADM3070E ADM3070EARZ SN65HVD73D SP3070EEN-L/TR RS-485 RS-422 TIA/EIA interface transceiver balanced differential signaling full duplex half duplex true fail-safe receiver one-eighth unit load ESD protection DE control input RE control input 3.3 V transceiver 250 kbps data rate 14-pin SOIC industrial automation building automation factory data acquisition robotics communication
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情