Microchip Technology

AT90CAN128-16AI - 16MHz 128KB AVR CAN MCU | Microchip

MPN: AT90CAN128-16AI ✓ Hoạt động
2.7 V to 5.5 V Vdss 64-TQFP, 14 mm x 14 mm Package 16 MHz Speed 128 KB Memory
MOQ: 1 |

AT90CAN128-16AI Tóm tắt

The Microchip Technology AT90CAN128-16AI is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 128 KB of in-system programmable flash, 4 KB of EEPROM, 4 KB of SRAM, and 53 general-purpose I/O lines in a 64-pin TQFP package. It integrates a CAN controller compliant with CAN V2.0A and V2.0B for industrial networking applications.

An 8-bit microcontroller is a compact embedded processing device built around an 8-bit register and data architecture. The AT90CAN128 belongs to the hierarchy of AVR enhanced RISC microcontrollers, embedded controllers, and general-purpose semiconductors. Its single-clock-cycle instruction execution and integrated CAN interface make it useful for control systems that require deterministic field-bus communication without a separate communications controller.

Key features include 128 KB of read-while-write ISP flash, 4 KB of EEPROM, 4 KB of SRAM, 32 general-purpose working registers, and 53 I/O lines. The device also provides four flexible timer/counters with compare and PWM modes, two USARTs, a byte-oriented two-wire serial interface, and a real-time counter. The CAN controller supports both CAN V2.0A and V2.0B protocol versions.

The AT90CAN128-16AI operates from 2.7 V to 5.5 V at up to 16 MHz and is specified over -40°C to +85°C. Its automotive-family data sheet reports qualification to AEC-Q100 for relevant family variants, while the -16AI ordering code is used for industrial-temperature production. The 64-TQFP package measures 14 mm by 14 mm and uses a surface-mount assembly process.

Typical applications include industrial CAN gateways, automotive body and accessory controllers, factory automation nodes, environmental monitoring equipment, and service tools that communicate with CAN 2.0 networks. Firmware can be programmed through the in-system programming interface, while bootloading and application code occupy the large on-chip flash memory.

Design with the CAN transceiver outside the microcontroller and connect the AT90CAN128 CAN_RX and CAN_TX pins through that interface. Keep the CAN bus differential traces short, symmetric, and away from switching nodes, and terminate both ends of the bus with the termination resistance specified by the network design. Confirm clock stability, reset behavior, and decoupling against the manufacturer datasheet before releasing a PCB.

This page combines the family datasheet specifications, package details, ordering-code comparisons, and application guidance with practical drop-in alternatives and PCB-level design considerations. These resources help engineers evaluate CAN protocol compatibility, peripheral availability, timing margins, and second-source options before committing to a design.

Bộ thay thế dễ dàng lắp đặt cho AT90CAN128-16AI — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AT90CAN128-16AI (cùng hình factor và footprint) — khác nhau ở General-Purpose I/O Lines, General-Purpose Working Registers, Package, CAN Controller, Flash Memory.

Microchip Technology
General-Purpose I/O Lines: 53 lines
General-Purpose Working Registers: 32 registers
Package: 64-pin TQFP, 14 mm x 14 mm
So sánh với AT90CAN128-16AI →
Microchip Technology
General-Purpose I/O Lines: 53 lines
General-Purpose Working Registers: 32 registers
Package: 64-pin TQFP, 14 mm x 14 mm
So sánh với AT90CAN128-16AI →

AT90CAN128-16AU

✅ Drop-In
Microchip Technology
📦 64-TQFP (14x14)
8-bit AVR RISC microcontroller with CAN controller · 16 MHz · 128 KB (128K x 8) · 4 KB · 4 KB · 53 lines · 32 registers · CAN 2.0A and CAN 2.0B compliant

Liên hệ để biết giá

Xem tài liệu →

AT90CAN128-16AUR

✅ Drop-In
📦 64-TQFP (14x14)
Identical 16 MHz, 128 KB, 4 KB EEPROM, 53 I/O, and CAN configuration with a reel supply format instead of the tray form represented by the -16AI ordering code

📋 Tham chiếu thay thế (không có trong danh mục)

AT90CAN128-16AJ

✅ Drop-In
Microchip Technology
📦 64-TQFP (14x14)
8-bit AVR RISC microcontroller with CAN controller · 16 MHz · 128 KB · 4 KB · 4 KB · 53 lines · 32 registers · CAN V2.0A and V2.0B

Liên hệ để biết giá

Xem tài liệu →

AT90CAN128-16AU

✅ Drop-In
Microchip Technology
📦 64-TQFP (14x14)
8-bit AVR RISC microcontroller with CAN controller · 16 MHz · 128 KB (128K x 8) · 4 KB · 4 KB · 53 lines · 32 registers · CAN 2.0A and CAN 2.0B compliant

Liên hệ để biết giá

Xem tài liệu →

AT90CAN128-16AI

✅ Drop-In
Microchip Technology
📦 64-TQFP (14x14)
8-bit RISC Flash Microcontroller · AVR enhanced RISC · 16 MHz · 128 KB · In-System Programmable with Read-While-Write · 4 KB · 4 KB · 53

Liên hệ để biết giá

Xem tài liệu →

AT90CAN128-16AI Tỷ lệ tối đa & tính chất điện

Device Type 8-bit RISC Flash Microcontroller
Architecture AVR enhanced RISC
Maximum Clock Speed 16 MHz
Program Flash Memory 128 KB
Flash Programming In-System Programmable with Read-While-Write
EEPROM 4 KB
SRAM 4 KB
General-Purpose I/O Lines 53
General-Purpose Working Registers 32
CAN Controller CAN V2.0A and CAN V2.0B compliant
Timer/Counters 4 with compare modes and PWM
USART Interfaces 2
Two-Wire Serial Interface 1 byte-oriented interface
Real-Time Counter 1
Operating Voltage Range 2.7 V to 5.5 V
Khoảng nhiệt độ hoạt động -40°C to +85°C
Hộp 64-TQFP, 14 mm x 14 mm
Kiểu lắp đặt Surface Mount
Process Technology Low-power CMOS

Hướng dẫn cấu hình chân AT90CAN128-16AI 64-tqfp, 14 mm x 14 mm

Cấu hình chân cho AT90CAN128-16AI (64-tqfp, 14 mm x 14 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 64-tqfp, 14 mm x 14 mm cho AT90CAN128-16AI

Không có dữ liệu chân cụ thể sẵn có cho AT90CAN128-16AI.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

AT90CAN128-16AI phù hợp cho 6 Áp dụngs: Industrial CAN Automation Node, Automotive Body and Accessory Controller, CAN-Based Environmental Monitoring Unit, CAN Gateway and Protocol Bridge, Factory Equipment Service Interface, CAN-Based Lighting and Auxiliary Control.

🏭

Industrial CAN Automation Node

The AT90CAN128-16AI fits an industrial automation node that must control local I/O while exchanging real-time data over a CAN 2.0 network. Its 16 MHz AVR core supports approximately 1 MIPS throughput, while 53 I/O lines leave substantial capacity for sensors, discrete outputs, status indicators, and service connectors. The integrated CAN controller supports CAN V2.0A and V2.0B, removing the need for an external protocol controller. Place the device beside an external CAN transceiver, keep the bus path compact, and terminate the network at both physical ends. The 2.7 V to 5.5 V operating range also supports 3.3 V and 5 V industrial rails.

🚗

Automotive Body and Accessory Controller

The AT90CAN128-16AI can serve as a body or accessory controller when the vehicle network uses CAN 2.0 and the module requires multiple local I/O functions. Its four timer/counters provide compare and PWM outputs for valves, lamps, or motor-control assistance, while two USARTs support service diagnostics and external sensors. The CAN V2.0A and V2.0B controller integrates directly into the module architecture. Automotive implementations should use the appropriate qualified family variant and validate the exact ordering code against Microchip automotive data sheet doc7682.pdf, including temperature, transient, and qualification requirements.

🧩

CAN-Based Environmental Monitoring Unit

A remote environmental monitor benefits from the AT90CAN128-16AI's combination of 53 I/O lines and a networked CAN interface. Inputs can cover temperature, humidity, smoke, water-level, and analog sensor conditioning, while outputs control indicators or sampling relays. Four flexible timer/counters with PWM and compare modes support periodic sampling and local actuator timing, and the real-time counter provides an independent scheduling resource. Its 4 KB EEPROM can retain calibration values and node identifiers, while the 128 KB flash provides room for protocol handling, diagnostics, and a bootloader.

🌐

CAN Gateway and Protocol Bridge

The AT90CAN128-16AI is appropriate for a gateway that bridges a CAN 2.0 segment to another serial or embedded subsystem. Two USARTs can connect downstream equipment, while the byte-oriented two-wire interface supports sensors or configuration storage. The 4 KB SRAM is sufficient for protocol buffering in modest gateway designs, and the 128 KB flash allows protocol translation, filtering, diagnostics, and firmware update logic. Separate CAN transceiver circuitry is required because the MCU provides the digital controller, not the bus differential driver. Validate bit timing, error handling, and bus termination during integration testing.

🔧

Factory Equipment Service Interface

The AT90CAN128-16AI can implement a local service interface on industrial equipment while the machine's main controller continues to operate over CAN. The two USARTs support a technician console and an external service adapter, and the two-wire interface permits connection to a maintenance peripheral or configuration storage. Because the device provides 53 general-purpose I/O, it can also supervise door switches, emergency-stop status, indicators, and relay feedback. Use the two USARTs and CAN controller for interrupt-driven event handling, and keep service connectors away from high-current switching traces to reduce noise coupling.

💡

CAN-Based Lighting and Auxiliary Control

The AT90CAN128-16AI can control lighting or auxiliary loads in an equipment network where a CAN master issues commands to distributed modules. Its PWM-capable timer/counters drive dimming, relays, or indicators, and its 53 I/O lines handle local switches and status feedback. The 16 MHz processing rate leaves headroom for command validation, debouncing, diagnostics, and communication error handling. For long cable runs or electrically noisy machinery, maintain a defined CAN network topology, use a qualified transceiver, route the bus away from motors, and verify common-mode voltage at the module interface.

Tóm tắt các sản phẩm được đề xuất

AT90CAN128-16AUR Same-family reel-supply configuration Được sử dụng trong: Industrial CAN Automation Node, Automotive Body and Accessory Controller, CAN Gateway and Protocol Bridge, CAN-Based Lighting and Auxiliary Control AT90CAN128-16AU Microchip Technology Được sử dụng trong: Industrial CAN Automation Node, CAN-Based Environmental Monitoring Unit, Factory Equipment Service Interface, CAN-Based Lighting and Auxiliary Control AT90CAN128-16AJ Microchip Technology Được sử dụng trong: Automotive Body and Accessory Controller, CAN Gateway and Protocol Bridge AT90CAN128-16A Same AT90CAN128 device family Được sử dụng trong: CAN-Based Environmental Monitoring Unit AT90CAN128-16AI Microchip Technology Được sử dụng trong: Factory Equipment Service Interface
What are the key specifications of AT90CAN128-16AI that engineers should know?
The AT90CAN128-16AI combines a 16 MHz AVR enhanced RISC core with 128 KB of ISP flash, 4 KB of EEPROM, 4 KB of SRAM, and 53 general-purpose I/O lines. It includes one CAN controller compliant with CAN V2.0A and V2.0B, four timer/counters with PWM, two USARTs, a byte-oriented two-wire interface, and a real-time counter. The Microchip family datasheet identifies the operating voltage range as 2.7 V to 5.5 V, while the -16AI industrial ordering code is specified from -40°C to +85°C.
Where can I download the AT90CAN128-16AI datasheet PDF?
The manufacturer data sheet for the AT90CAN32, AT90CAN64, and AT90CAN128 family is available directly from Microchip as document doc7679.pdf. It covers flash, SRAM, EEPROM, CAN, timers, serial interfaces, electrical limits, and package information for the AT90CAN128-16AI. A separate automotive family data sheet is published as doc7682.pdf. Use the pin-description and electrical-characteristic tables in those documents when assigning PCB signals and checking timing or power limits.
Where can I find the AT90CAN128 pinout and package details?
The AT90CAN128-16AI uses a 64-pin TQFP package measuring 14 mm by 14 mm. Its pin assignments, including power, ground, reset, programming, general-purpose I/O, timer, USART, two-wire serial, and CAN signals, are listed in the Microchip family data sheet doc7679.pdf. Use the package drawing and pin-description table together when planning land patterns, because the exposed underside area and lead dimensions must match the manufacturer drawing rather than a generic TQFP footprint.
How do I program an AT90CAN128-16AI?
The AT90CAN128-16AI supports in-system programming of its 128 KB flash memory. Microchip programming tools can use the serial programming interface through the dedicated programming pins, while the large flash capacity allows an application bootloader and field-update routine to coexist with operating firmware. Before programming, confirm the configured clock source, reset state, boot-lock settings, and fuse configuration in the family data sheet. The 4 KB EEPROM can also retain configuration values without occupying flash space.
Is the AT90CAN128-16AI suitable for industrial CAN bus controllers?
The AT90CAN128-16AI is suitable for industrial CAN nodes because it combines a 16 MHz AVR core with a CAN controller supporting CAN V2.0A and V2.0B. Its 53 I/O lines, four timer/counters, two USARTs, and two-wire interface support local sensing, actuator control, and service-port communication. The industrial ordering code operates from 2.7 V to 5.5 V and across -40°C to +85°C, matching many factory equipment environments when combined with an external CAN transceiver.
What is the difference between AT90CAN128-16AU and AT90CAN128-16AI?
Both parts belong to the 128 KB, 16 MHz AT90CAN128 family and use the same 64-pin TQFP device organization. Their ordering suffixes identify different commercial configurations, and the manufacturer product documentation should be checked for the exact temperature, packaging, and qualification terms attached to each code. The AT90CAN128-16AI is specified for -40°C to +85°C operation. When substituting an ordering code, verify the mounted package, pin orientation, programming interface, and temperature grade rather than relying on the shared flash and CAN specifications.
Can AT90CAN128-16AUR replace AT90CAN128-16AI?
The AT90CAN128-16AUR is a reel-ordering configuration of the same AT90CAN128 device family and is mechanically compatible with the 64-pin TQFP footprint used by the AT90CAN128-16AI. Electrical drop-in use still requires confirmation of the ordering-code temperature rating, qualification status, and supply format. The reel format changes handling rather than the pin arrangement, but automated assembly lines may require the packaging code to be updated in the bill of materials before substitution.
What is the best drop-in replacement for AT90CAN128-16AI?
The closest drop-in choices are same-family AT90CAN128 ordering variants in the 64-pin TQFP package, including AT90CAN128-16AU and AT90CAN128-16AUR. They preserve the 16 MHz AVR core, 128 KB flash, 4 KB EEPROM, 4 KB SRAM, 53 I/O lines, and integrated CAN controller. Before approving any substitute, confirm the temperature range, qualification level, packaging form, and CAN electrical behavior against the manufacturer data sheet. No cross-brand part with an independently verified 64-pin pin-compatible CAN interface was identified.
What can replace AT90CAN128-16AI?
A replacement must preserve the 64-pin TQFP land pattern, 2.7 V to 5.5 V operation, 16 MHz performance, and the peripheral arrangement used by the firmware. Same-family AT90CAN128-16AU, AT90CAN128-16AUR, and AT90CAN128-16AJ ordering variants are the closest candidates because they retain the AVR core, memory configuration, and CAN controller. Treat a non-Microchip MCU as a redesign unless its complete pin mapping, interrupt behavior, memory map, and CAN register interface have been verified.
When should I choose AT90CAN128-16AI over ATMEGA128-16ANR?
Choose the AT90CAN128-16AI when the design requires an integrated CAN V2.0A and V2.0B controller and dedicated CAN RX and TX functions. The ATMEGA128-16ANR shares the general 8-bit AVR and 128 KB flash class and is listed in 64-pin TQFP options, but it does not provide the same dedicated CAN controller. Moving between the two device families requires review of pin functions, interrupts, electrical characteristics, firmware, and the migration guidance in Microchip application note AVR096.
Is AT90CAN128-16AI the same as AT90CAN128-16AUR?
They are not the same ordering code, but they are closely related AT90CAN128 configurations with the same 128 KB flash, 4 KB EEPROM, 4 KB SRAM, 53 I/O lines, and CAN controller. The principal differences involve the ordering suffix, supply packaging, and possibly the commercial or temperature specification attached to that suffix. For a PCB replacement, verify the 64-pin TQFP footprint and operating conditions. For production, also confirm whether the reel configuration suits the assembly process.
What is the best Microchip equivalent for AT90CAN128-16AI?
Among the verified Microchip alternatives, AT90CAN128-16AU is the closest ordering variant for an industrial-temperature design, while AT90CAN128-16AUR serves the corresponding reel-supply configuration. Both retain the same 16 MHz, 128 KB, 4 KB EEPROM, 4 KB SRAM, 53-I/O device core and integrated CAN controller. Microchip does not present a different manufacturer as a drop-in equivalent, so use the ordering-code documentation to confirm temperature and qualification requirements before substitution.
How much CAN and peripheral performance does the AT90CAN128-16AI provide?
The AT90CAN128-16AI uses a low-power CMOS AVR enhanced RISC architecture that executes powerful instructions in a single clock cycle. The family documentation describes throughput approaching 1 MIPS per MHz, which corresponds to approximately 16 MIPS at the 16 MHz operating frequency. Peripherals include one CAN controller, four timer/counters with compare and PWM functions, two USARTs, a byte-oriented two-wire interface, and a real-time counter for scheduled interrupt handling.
Where can I buy AT90CAN128-16AI and what is its lead time?
Use the Request a Quote form on this page to request the current unit price, stock position, minimum order quantity, and lead time for the exact AT90CAN128-16AI ordering code. Quote requests should include the required package, production quantity, and target date. For long-lived industrial programs, request a lifecycle confirmation and managed sourcing plan at the time of quotation because market availability can change independently of the device's technical specification.
What is the price of AT90CAN128-16AI?
The current commercial price for the AT90CAN128-16AI is obtained through the Request a Quote form on this page. Enter the required quantity and ordering details so the quote reflects the correct package, production volume, and delivery requirements. For engineering budgeting, use the manufacturer family data sheet and the device's 128 KB flash, 64-pin TQFP, and industrial-temperature specifications to identify the correct alternate before requesting a production quotation.
Is AT90CAN128-16AI in stock?
Stock and scheduled delivery should be confirmed through the Request a Quote form on this page using the exact AT90CAN128-16AI part number and your required quantity. Because this is a legacy AVR family with multiple ordering codes, a quotation response can confirm whether the industrial-temperature configuration is the one allocated. Do not substitute a tray, reel, or different temperature suffix without confirming that the assembly process and electrical requirements remain acceptable.

Dữ liệu tham khảo kỹ thuật cho AT90CAN128-16AI — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Select the AT90CAN128-16AI when an industrial design needs a 16 MHz AVR controller with 128 KB flash, 53 I/O lines, and an integrated CAN V2.0A/V2.0B controller in a 64-pin TQFP package. Its 4 KB EEPROM supports retained configuration, while four timer/counters and two USARTs cover common sensing, actuator, and service-port requirements. Choose AT90CAN128-16AUR when automated assembly requires a reel-oriented supply configuration and confirm the temperature terms first. Choose AT90CAN128-16AU when its ordering-code commercial and temperature terms match the product requirements. Do not select the ATMEGA128-16ANR solely for pin count or shared AVR heritage; without a dedicated CAN controller, it requires a different interface strategy. For any legacy program, validate CAN timing, memory compatibility, reset behavior, and firmware against the family and migration documentation before releasing a replacement.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này AT90CAN128-16AU AT90CAN128-16AUR AT90CAN128-16AJ AT90CAN128-16A
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 64-TQFP (14x14) 64-TQFP (14x14) 64-TQFP (14x14) 64-TQFP (14x14) 64-TQFP (14x14)
Clock Speed 16 MHz 16 MHz 16 MHz 16 MHz 16 MHz
Flash Memory 128 KB 128 KB 128 KB 128 KB 128 KB
EEPROM 4 KB 4 KB 4 KB 4 KB 4 KB
SRAM 4 KB 4 KB 4 KB 4 KB 4 KB
General-Purpose I/O 53 lines 53 lines 53 lines 53 lines 53 lines
CAN Protocol Support CAN V2.0A and CAN V2.0B CAN V2.0A and CAN V2.0B CAN V2.0A and CAN V2.0B CAN V2.0A and CAN V2.0B CAN V2.0A and CAN V2.0B
Supply Voltage 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Timer/Counters 4 with compare and PWM modes 4 with compare and PWM modes 4 with compare and PWM modes 4 with compare and PWM modes 4 with compare and PWM modes

Bảo phân biệt quan trọng

  • Integrated CAN controller eliminates an external protocol controller (vsATMEGA128-16ANR)
  • Large integrated memory supports standalone CAN nodes (vsAT90CAN64-16AU)
  • Same-family ordering alternatives simplify second-source review (vsAT90CAN128-16AUR)
  • Broad serial and timing resources cover more local functions (vsATMEGA128-16ANR)

Ghi chú thiết kế

The AT90CAN128 CAN_RX and CAN_TX signals are digital MCU signals and must connect to an external CAN transceiver rather than directly to a differential bus. Route the MCU-to-transceiver path as a short pair, keep the transceiver close to the connector, and place the bus termination only at the physical ends of the network. Avoid routing CAN traces alongside switching-power nodes, relay contacts, or motor drive outputs.

Operate the device within its 2.7 V to 5.5 V supply range and follow the decoupling configuration in the manufacturer family data sheet. Place low-ESR capacitors at the supply pins with short ground returns, and use a quiet ground-plane connection for the MCU and CAN transceiver. If a switching regulator supplies the rail, reserve filtering or an LDO for the transceiver and MCU section when conducted and radiated emissions become critical.

CAN bit timing depends on the selected clock source and oscillator tolerance. Use the clock configuration recommended for the board, account for temperature-dependent frequency variation, and verify the point-to-point delay budget with the transceiver and cable characteristics included. Validate the controller's sample point and propagation delay settings in the deployed bus, including bus loading, rather than relying only on a bench test with short cables.

Do not treat the AT90CAN128 and ATMEGA128 as firmware-compatible merely because both use the AVR architecture. Microchip application note AVR096 explains that their electrical characteristics differ and that a migration requires datasheet review. Preserve the exact 64-pin land pattern, verify CAN pin assignments, check reset and programming connections, and retest interrupt priorities, timing, and startup behavior after changing ordering codes or device families.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

Microchip automotive data sheet doc7682.pdf states that the AT90CAN32, AT90CAN64, and AT90CAN128 family has undergone AEC-Q100 qualification. The AT90CAN128-16AI ordering code is an industrial-temperature configuration, so the automotive qualification must not be applied directly to this exact orderable variant.

Dữ liệu được xác minh vào: 2026-11-20 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

at90can128 datasheet at90can128 pinout at90can128 16au datasheet at90can128 programming at90can128 development board at90can128 pdf AT90CAN128-16AI datasheet AT90CAN128-16AI pinout AT90CAN128-16AI equivalent AT90CAN128-16AI replacement AT90CAN128-16AI vs AT90CAN128-16AU AT90CAN128 TQFP-64 footprint AT90CAN128 CAN 2.0 controller AT90CAN128 industrial application circuit

Các bộ phận và thuật ngữ liên quan

Microchip Technology AT90CAN128-16AI AT90CAN128-16AU AT90CAN128-16AUR AT90CAN128-16AJ AT90CAN128 AT90CAN64-16AU ATMEGA128-16ANR AVR enhanced RISC architecture 8-bit microcontroller CAN controller CAN V2.0A CAN V2.0B In-System Programming Read-While-Write TQFP-64 surface mount general-purpose I/O USART two-wire serial interface timer/counter PWM real-time counter EEPROM AEC-Q100 RoHS industrial automation automotive body control
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ