AUIRF7640S2TR - 60V 21A DirectFET MOSFET for Class D | Infineon
MPN: AUIRF7640S2TR ✓ Hoạt độngAUIRF7640S2TR Tóm tắt
A DirectFET MOSFET is a chip-scale surface-mount power package in which the silicon die is mounted on a metallic can that forms both the drain contact and a low-resistance thermal path to the PCB. Unlike a standard SO-8 or DPAK, DirectFET places the source and gate on the top side and the drain on the bottom, providing an extremely low package resistance and superior thermal performance for the same footprint. The DirectFET SB case variant is widely used in audio amplifier output stages where both low RDS(on) and clean thermal management are required.
Key features include a logic-level compatible gate drive, low total gate charge (Qg = 7.3 nC typical) that minimizes driver losses, and an automotive-grade qualification flow targeting AEC-Q101 reliability. The part is rated for avalanche operation and is intended for high-frequency PWM switching in the 250 kHz to 500 kHz range typical of Class D amplifiers. The DirectFET SB land pattern is electrically and thermally compatible with industry-standard layouts, simplifying PCB design and enabling vapor-phase, infrared, or conventional reflow soldering.
Typical applications include automotive Class D audio amplifiers (4 Ω and 8 Ω loads), high-current DC-DC synchronous rectifiers, motor drive half-bridges, and OR-ing FETs in redundant power systems. The combination of 60 V rating and 21 A continuous drain current makes it suitable for 12 V and 24 V automotive bus rails where load-dump transients must be tolerated.
When designing with this part, ensure that the PCB copper area under the DirectFET can is sized to keep junction temperature below 150 °C at worst-case load. The gate drive should swing at least 10 V for full RDS(on) optimization, although the part will turn on at 4.5 V. Always consult the manufacturer datasheet for SOA curves and thermal derating under pulsed audio loads.
Bộ thay thế dễ dàng lắp đặt cho AUIRF7640S2TR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AUIRF7640S2TR (cùng hình factor và footprint) — khác nhau ở Package, Technology, Drain-Source Voltage (VDS), Automotive Qualification, Configuration.
AUIRF7640S2TR1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AUIRF7640S2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AUIRF7769L2TR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →IRF6645TRPBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
IRF7240TRPBF
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AUIRF7640S2TR Tỷ lệ tối đa & tính chất điện
| FET Type | N-Channel |
| Drain-Source Voltage (VDS) | 60 V |
| Continuous Drain Current (ID) @ TA=25C | 5.8 A |
| Continuous Drain Current (ID) @ TC=25C | 21 A |
| Power Dissipation (PD) @ TA=25C | 2.4 W |
| Power Dissipation (PD) @ TC=25C | 30 W |
| On-Resistance RDS(on) | 36 mΩ |
| Total Gate Charge (Qg) | 7.3 nC |
| Hộp | DirectFET SB (Surface Mount) |
| Kiểu lắp đặt | Surface Mount |
| Technology | HEXFET Power MOSFET (Automotive Grade) |
| Automotive Qualification | AEC-Q101 (Automotive Grade per datasheet) |
| Primary Application | Automotive Class D audio amplifier output stage |
Hướng dẫn cấu hình chân AUIRF7640S2TR directfet sb (surface mount)
Cấu hình chân cho AUIRF7640S2TR (directfet sb (surface mount) gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho AUIRF7640S2TR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Khu vực hoạt động an toàn - DC
Ứng dụng tiêu biểu
AUIRF7640S2TR phù hợp cho 6 Áp dụngs: Automotive Class D Audio Amplifier Output Stage, Automotive 12V/24V Synchronous Buck Converter, Automotive DC Motor Drive Half-Bridge, Automotive OR-ing / Power Muxing FET, Industrial High-Frequency Switching Power Supply, Automotive LED Driver Output Stage.
Automotive Class D Audio Amplifier Output Stage
The AUIRF7640S2TR is specifically designed for automotive Class D audio amplifier output stages switching at 250 kHz to 500 kHz PWM frequencies into 4 Ω and 8 Ω speaker loads. Per the Infineon datasheet, its 36 mΩ RDS(on) at VGS = 10 V minimizes conduction loss, while the 7.3 nC total gate charge keeps driver switching losses low. The DirectFET SB package's low package resistance and excellent thermal path to PCB copper enable continuous 21 A output current at 25 °C case temperature without external heatsinking. AEC-Q101 automotive qualification ensures the part survives underhood thermal cycling and load-dump transients typical of 12 V automotive electrical systems.
Được đề xuất
Automotive 12V/24V Synchronous Buck Converter
The AUIRF7640S2TR functions as a low-side synchronous rectifier in 12 V and 24 V automotive DC-DC converters, where its 36 mΩ RDS(on) and 60 V VDS rating provide headroom for transient events. According to the Infineon datasheet, the part's DirectFET SB package occupies less board area than DPAK while offering superior thermal coupling. The 7.3 nC Qg simplifies gate-drive design in 200 kHz to 500 kHz buck topologies commonly used for automotive infotainment and ADAS power rails.
Được đề xuất
Automotive DC Motor Drive Half-Bridge
The AUIRF7640S2TR is well-suited as a high-side or low-side switch in automotive brushed DC motor half-bridges for pumps, fans, and small actuators. The Infineon datasheet specifies 21 A continuous ID at TC and avalanche ruggedness, enabling direct drive of inductive loads without additional protection. The DirectFET SB package handles the high di/dt and dv/dt of PWM motor control at 20 kHz to 50 kHz without ringing issues common to wire-leaded packages.
Được đề xuất
Automotive OR-ing / Power Muxing FET
The AUIRF7640S2TR serves as an OR-ing FET in redundant automotive power systems such as dual-battery setups and eCall backup supplies. According to the Infineon datasheet, the low 36 mΩ RDS(on) minimizes voltage drop and power dissipation in continuous-carry applications, while the 60 V VDS rating tolerates jump-start and load-dump transients. The DirectFET SB package's low thermal impedance keeps junction temperature low without external heatsinking.
Được đề xuất
Industrial High-Frequency Switching Power Supply
The AUIRF7640S2TR is used in industrial switch-mode power supplies where 60 V VDS, 21 A continuous ID, and DirectFET SB thermal performance are required. Per the Infineon datasheet, the part supports hard-switched topologies up to 500 kHz and resonant topologies beyond 1 MHz, taking advantage of low Qrr and low Qg. Automotive-grade reliability provides extended MTBF in 24/7 industrial installations.
Được đề xuất
Automotive LED Driver Output Stage
The AUIRF7640S2TR can be used as a constant-current regulator or PWM switch in high-brightness automotive LED headlight and daytime running light applications. The Infineon datasheet specifies that the part's 36 mΩ RDS(on) and DirectFET SB thermal performance handle the 2 A to 5 A continuous currents typical of automotive LED strings. AEC-Q101 qualification and the -40 °C to +150 °C operating range match underhood and headlamp module environments.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AUIRF7640S2TR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AUIRF7640S2TR1 | AUIRF7640S2 | AUIRF7769L2TR | IRF6645TRPBF | IRF7240TRPBF |
|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | DirectFET SB | DirectFET SB - same | DirectFET SB - same | DirectFET L2 - same family, different case | DirectFET SB - same | DirectFET MZ - same family, different case |
| Drain-Source Voltage (VDS) | 60 V | 60 V | 60 V | 100 V | 100 V | 40 V |
| Continuous Drain Current (ID @ TC) | 21 A | 21 A | 21 A | 10 A | 19 A | 20 A |
| On-Resistance RDS(on) | 36 mΩ | 36 mΩ | 36 mΩ | 12 mΩ | 40 mΩ | 50 mΩ |
| Total Gate Charge (Qg) | 7.3 nC | 7.3 nC | 7.3 nC | 20 nC | 8.0 nC | 15 nC |
| Automotive Qualification | AEC-Q101 | AEC-Q101 | AEC-Q101 | AEC-Q101 | Industrial grade (non-auto) | Industrial grade (non-auto) |
| Primary Application | Class D audio amplifier | Class D audio amplifier | Class D audio amplifier | High-frequency DC-DC | DC-DC synchronous rectification | Low-voltage DC-DC sync rect |
Bảo phân biệt quan trọng
- Automotive-grade qualification on a DirectFET-class part (vsIRF6645TRPBF)
- Lower RDS(on) than IRF6645 in same package (vsIRF6645TRPBF)
- Right voltage rating for 12V/24V automotive bus (vsIRF7240TRPBF)
Ghi chú thiết kế
Estimated: at ID = 10 A continuous and RDS(on) = 36 mΩ, conduction loss is approximately 3.6 W. Using a typical DirectFET SB junction-to-ambient thermal resistance of 50 C/W on a 1 oz 2 square-inch copper pour, junction temperature rises 180 °C above ambient. For continuous Class D audio operation, increase PCB copper area to at least 3-4 square inches or use multiple thermal vias to an internal copper plane to keep Tj below 150 °C. Always consult the manufacturer datasheet SOA curves for your specific pulse profile.
DirectFET SB layout requires that the drain copper pad cover the entire footprint of the metal can, with multiple thermal vias stitching to the opposite copper plane. Gate and source pads are on the top side of the package. Place the gate driver within 5 mm of the gate pad to minimize parasitic inductance; for switching above 100 kHz, add a 10 Ω gate-source resistor to prevent ringing.
Do not exceed VGS = ±20 V absolute maximum, even though the part is rated to handle avalanche. For Class D audio half-bridges, ensure the gate-source voltage of the high-side FET does not exceed ratings during the bootstrap charge phase - use a bootstrap capacitor with at least 100 nF and verify the high-side supply voltage under worst-case audio load.
Thông tin tuân thủ
AEC-Q101 qualified (MOSFET automotive standard, distinct from AEC-Q100 which is for ICs). RoHS and lead-free per Infineon product page.
