BCM53115MKFBG - 7-Port Gigabit Ethernet Switch | Broadcom
MPN: BCM53115MKFBG ✓ Hoạt độngBCM53115MKFBG Tóm tắt
A Gigabit Ethernet switch is a networking semiconductor that forwards Ethernet frames between connected ports while supporting full-duplex communication, auto-negotiation, and traffic management. In the broader hierarchy, it belongs to Ethernet interface ICs, then network interface controllers and switching silicon, and ultimately the semiconductor category. Integrated PHYs reduce the external active Ethernet component count, although magnetics, termination, isolation, and layout requirements still shape the final board design.
The BCM53115MKFBG provides seven Gigabit Ethernet ports, integrated PHYs, 65 nm LP CMOS implementation, and a 400-ball BGA package. Its integration can simplify multi-port equipment compared with a design assembled from several discrete Ethernet interface components. The compact BGA footprint also requires careful PCB routing, thermal analysis, and manufacturing controls because its fine-pitch balls and exposed underside area demand precise layout practices.
The device is applicable to industrial Ethernet switches, router and gateway platforms, broadband access equipment, network surveillance systems, and other multi-port products. For each PHY-facing port, the board must provide the appropriate magnetic interface or supported copper-media interface, power supplies, and controlled-impedance routing. System designers should also validate timing, thermal performance, firmware support, and management features against the Broadcom datasheet and reference designs.
Because the BCM53115MKFBG is a BGA device, layout is a central part of successful implementation. Place decoupling close to the relevant supply pins, keep high-speed traces short, provide adequate reference planes, route differential pairs with controlled impedance, and use an appropriate via field and ball-to-trace transition. PCB assembly should be qualified for the package density and thermal profile used in the finished product.
This page summarizes the verified 7-port Gigabit Ethernet switch identity, records the available package and process information, and identifies practical evaluation points for replacement and hardware design. Detailed electrical limits, register behavior, timing, clock requirements, and absolute maximum ratings should be taken directly from the current Broadcom manufacturer datasheet before schematic release or production qualification.
Bộ thay thế dễ dàng lắp đặt cho BCM53115MKFBG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với BCM53115MKFBG (cùng hình factor và footprint).
BCM53115MKPBG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM53115MKFB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
88E6190X
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ9893RNXI
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →RTL838X
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM53115MKFBG Tỷ lệ tối đa & tính chất điện
| Product Type | 7-port Gigabit Ethernet switch with integrated PHYs |
| Number of Gigabit Ethernet Ports | 7 ports |
| Integrated PHY Count | 7 integrated Gigabit PHYs |
| Process Technology | 65 nm LP CMOS |
| Package Type | 400-ball BGA, square |
| Number of Terminals | 400 terminals |
| Device Category | Ethernet interface IC / switching IC |
| Ethernet Data Rate | 1 Gb/s per port |
| Trạng thái RoHS | Compliant |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân BCM53115MKFBG 400-ball bga, square
Cấu hình chân cho BCM53115MKFBG (400-ball bga, square gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho BCM53115MKFBG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BCM53115MKFBG phù hợp cho 6 Áp dụngs: Industrial Ethernet Switch, Router and Gateway Platform, Broadband Access Equipment, Network Surveillance System, Embedded Network Controller, Network Test Equipment.
Industrial Ethernet Switch
The BCM53115MKFBG fits industrial Ethernet switch platforms requiring seven Gigabit Ethernet ports in one switching IC. Its seven integrated PHYs provide the physical-layer functions for copper media interfaces while reducing the number of separate transceiver blocks. A board designer must still implement compliant Ethernet magnetics or supported media circuitry, controlled-impedance routing, robust power distribution, and surge protection appropriate to the installation environment. The 400-ball BGA also makes PCB density, via-in-pad decisions, assembly yield, and thermal verification central parts of an industrial design. Before release, verify temperature range, power-loss behavior, recovery features, and management requirements against the manufacturer documentation.
Được đề xuất
Router and Gateway Platform
A seven-port Gigabit Ethernet arrangement is useful in routers, gateways, and edge appliances where several wired endpoints must connect to a central forwarding engine. The BCM53115MKFBG combines seven Gigabit PHYs with the Ethernet switching function in 65 nm LP CMOS silicon, supporting a compact multi-port architecture. The design must accommodate the required clock, management interface, reset behavior, and power rails while keeping the 400-ball BGA routing orderly. Magnetic components and copper-media compliance remain board-level concerns, and the enclosure, thermal environment, and traffic load should be tested with the intended switch configuration.
Được đề xuất
Broadband Access Equipment
The BCM53115MKFBG can serve as the seven-port Gigabit switching element in broadband access and customer-premises equipment that aggregates multiple wired connections. Integrated PHYs allow the equipment architect to establish several 1 Gb/s copper-facing ports around one switching device rather than using multiple standalone transceivers. Because access products often depend on strict interoperability and line-card power behavior, the implementation should follow the Broadcom reference design for clocks, decoupling, media interfaces, and thermal construction. Validate boot sequencing, management behavior, fault recovery, and electromagnetic performance in the complete enclosure rather than relying on IC-level simulation alone.
Được đề xuất
Network Surveillance System
The BCM53115MKFBG is suitable for a networked camera or surveillance controller that needs several Gigabit Ethernet links for cameras, recorders, and uplink equipment. The seven integrated PHYs offer a path to a compact seven-port topology without requiring seven separate multi-port interface blocks. The finished surveillance product must account for cable reach, isolation, surge events, grounding, and power-loss behavior, while the 400-ball BGA needs careful decoupling, thermal relief, and assembly yield management. The seven-port configuration also allows efficient segmentation of cameras and uplinks when the Broadcom management and traffic-control features match the system requirements.
Được đề xuất
Embedded Network Controller
The BCM53115MKFBG can provide a multi-port wired-network front end for an embedded controller, test appliance, or industrial computing platform. Seven integrated Gigabit PHYs create a common switching endpoint for service equipment, test instruments, or local peripherals connected over Ethernet. The system designer should confirm clock sources, firmware requirements, management interfaces, and PHY register configuration before finalizing the architecture. PCB implementation should preserve high-speed signal integrity through short references, appropriate return paths, controlled-impedance differential routing, and dense decoupling around the BGA. Thermal performance should be evaluated with the expected sustained port traffic and the complete enclosure rather than under an isolated-device test condition.
Được đề xuất
Network Test Equipment
A seven-port Gigabit switching device is useful in test and measurement equipment that must provide multiple physical network connections for traffic generation, loopback analysis, or endpoint simulation. The BCM53115MKFBG offers seven integrated PHYs in 65 nm LP CMOS, allowing a compact instrument architecture with multiple active copper interfaces. Precise clocking, deterministic startup, port-status monitoring, and reliable thermal operation become important in laboratory and production-test environments. The 400-ball package requires a high-density PCB with validated assembly processes, and the Ethernet media interfaces must be designed for the cable lengths and isolation requirements of the target test environment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BCM53115MKFBG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BCM53115MKPBG | BCM53115MKFB | 88E6190X | KSZ9893 | RTL838X |
|---|---|---|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom | Marvell | Microchip Technology | Realtek |
| Package | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA |
| Integrated PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs |
| Ethernet Data Rate | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port |
Bảo phân biệt quan trọng
- Seven integrated Gigabit PHYs in one switching device (vsKSZ9893)
- Compact 65 nm LP CMOS implementation (vsRTL838X)
- Exact BCM53115 family continuity (vs88E6190X)
- Seven-port copper Ethernet consolidation (vsKSZ8041TLI-TR)
Ghi chú thiết kế
Treat the BCM53115MKFBG as a high-density BGA design. Follow the manufacturer land pattern exactly, provide local supply and ground connections, and route sensitive clock and Ethernet interfaces with continuous reference planes. Verify differential impedance and length rules against the official design guidance rather than relying on generic Ethernet routing conventions. The board should also include a practical assembly stack-up capable of supporting the package's ball pitch and thermal requirements.
Estimate junction temperature from actual 65 nm LP CMOS switching activity, the specified ambient temperature, and copper or heat-spreader performance in the finished enclosure. BGA thermal behavior depends strongly on via arrays, solder-mask and copper-pad design, airflow, and neighboring heat sources. Validate the assembled board with sustained traffic across all seven ports and confirm that the package junction-temperature limit is maintained during worst-case operation.
Keep clock traces short and isolated from noisy switching paths, and use the manufacturer's clocking and decoupling recommendations without increasing trace lengths unnecessarily. Ethernet differential pairs should maintain continuous return paths and controlled impedance through layer transitions. Avoid placing unrelated vias or test points in high-speed regions, and verify edge-rate behavior, crosstalk, and electromagnetic compliance on physical prototypes.
A common mistake is treating a same-family or cross-brand Ethernet IC as interchangeable solely because it is also a multi-port Gigabit switch. Before substituting BCM53115MKPBG, BCM53115MKFB, 88E6190X, KSZ9893, or an RTL838X device, compare the exact ordering suffix, ball map, power rails, clock input, management interface, PHY characteristics, and reference circuitry. An apparent package match does not prove pin-to-pin compatibility.
Thông tin tuân thủ
RoHS compliance is stated in the JLCPCB product result. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current compliance documentation.