BCM53115MKFBG - 7-Port Gigabit Ethernet Switch | Broadcom
MPN: BCM53115MKFBG ✓ 啟用中BCM53115MKFBG 概覽
A Gigabit Ethernet switch is a networking semiconductor that forwards Ethernet frames between connected ports while supporting full-duplex communication, auto-negotiation, and traffic management. In the broader hierarchy, it belongs to Ethernet interface ICs, then network interface controllers and switching silicon, and ultimately the semiconductor category. Integrated PHYs reduce the external active Ethernet component count, although magnetics, termination, isolation, and layout requirements still shape the final board design.
The BCM53115MKFBG provides seven Gigabit Ethernet ports, integrated PHYs, 65 nm LP CMOS implementation, and a 400-ball BGA package. Its integration can simplify multi-port equipment compared with a design assembled from several discrete Ethernet interface components. The compact BGA footprint also requires careful PCB routing, thermal analysis, and manufacturing controls because its fine-pitch balls and exposed underside area demand precise layout practices.
The device is applicable to industrial Ethernet switches, router and gateway platforms, broadband access equipment, network surveillance systems, and other multi-port products. For each PHY-facing port, the board must provide the appropriate magnetic interface or supported copper-media interface, power supplies, and controlled-impedance routing. System designers should also validate timing, thermal performance, firmware support, and management features against the Broadcom datasheet and reference designs.
Because the BCM53115MKFBG is a BGA device, layout is a central part of successful implementation. Place decoupling close to the relevant supply pins, keep high-speed traces short, provide adequate reference planes, route differential pairs with controlled impedance, and use an appropriate via field and ball-to-trace transition. PCB assembly should be qualified for the package density and thermal profile used in the finished product.
This page summarizes the verified 7-port Gigabit Ethernet switch identity, records the available package and process information, and identifies practical evaluation points for replacement and hardware design. Detailed electrical limits, register behavior, timing, clock requirements, and absolute maximum ratings should be taken directly from the current Broadcom manufacturer datasheet before schematic release or production qualification.
直接替換替代品,適用於 BCM53115MKFBG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: BCM53115MKFBG (相同外形與佔位).
BCM53115MKPBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM53115MKFB
✅ 直接替換📋 參考替代品(不在目錄中)
88E6190X
✅ 直接替換📋 參考替代品(不在目錄中)
KSZ9893RNXI
✅ 直接替換聯絡詢價
查看資料表 →RTL838X
✅ 直接替換📋 參考替代品(不在目錄中)
BCM53115MKFBG 最大額定值與電氣特性
| Product Type | 7-port Gigabit Ethernet switch with integrated PHYs |
| Number of Gigabit Ethernet Ports | 7 ports |
| Integrated PHY Count | 7 integrated Gigabit PHYs |
| Process Technology | 65 nm LP CMOS |
| Package Type | 400-ball BGA, square |
| Number of Terminals | 400 terminals |
| Device Category | Ethernet interface IC / switching IC |
| Ethernet Data Rate | 1 Gb/s per port |
| RoHS 狀態 | Compliant |
| 安裝類型 | Surface mount |
BCM53115MKFBG 400-ball bga, square 腳位配置指南
BCM53115MKFBG(400-ball bga, square 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: BCM53115MKFBG.
請參閱 資料表 以查看完整腳位配置。
典型應用
BCM53115MKFBG 適用於 6 應用s: Industrial Ethernet Switch, Router and Gateway Platform, Broadband Access Equipment, Network Surveillance System, Embedded Network Controller, Network Test Equipment.
Industrial Ethernet Switch
The BCM53115MKFBG fits industrial Ethernet switch platforms requiring seven Gigabit Ethernet ports in one switching IC. Its seven integrated PHYs provide the physical-layer functions for copper media interfaces while reducing the number of separate transceiver blocks. A board designer must still implement compliant Ethernet magnetics or supported media circuitry, controlled-impedance routing, robust power distribution, and surge protection appropriate to the installation environment. The 400-ball BGA also makes PCB density, via-in-pad decisions, assembly yield, and thermal verification central parts of an industrial design. Before release, verify temperature range, power-loss behavior, recovery features, and management requirements against the manufacturer documentation.
推薦
Router and Gateway Platform
A seven-port Gigabit Ethernet arrangement is useful in routers, gateways, and edge appliances where several wired endpoints must connect to a central forwarding engine. The BCM53115MKFBG combines seven Gigabit PHYs with the Ethernet switching function in 65 nm LP CMOS silicon, supporting a compact multi-port architecture. The design must accommodate the required clock, management interface, reset behavior, and power rails while keeping the 400-ball BGA routing orderly. Magnetic components and copper-media compliance remain board-level concerns, and the enclosure, thermal environment, and traffic load should be tested with the intended switch configuration.
推薦
Broadband Access Equipment
The BCM53115MKFBG can serve as the seven-port Gigabit switching element in broadband access and customer-premises equipment that aggregates multiple wired connections. Integrated PHYs allow the equipment architect to establish several 1 Gb/s copper-facing ports around one switching device rather than using multiple standalone transceivers. Because access products often depend on strict interoperability and line-card power behavior, the implementation should follow the Broadcom reference design for clocks, decoupling, media interfaces, and thermal construction. Validate boot sequencing, management behavior, fault recovery, and electromagnetic performance in the complete enclosure rather than relying on IC-level simulation alone.
推薦
Network Surveillance System
The BCM53115MKFBG is suitable for a networked camera or surveillance controller that needs several Gigabit Ethernet links for cameras, recorders, and uplink equipment. The seven integrated PHYs offer a path to a compact seven-port topology without requiring seven separate multi-port interface blocks. The finished surveillance product must account for cable reach, isolation, surge events, grounding, and power-loss behavior, while the 400-ball BGA needs careful decoupling, thermal relief, and assembly yield management. The seven-port configuration also allows efficient segmentation of cameras and uplinks when the Broadcom management and traffic-control features match the system requirements.
推薦
Embedded Network Controller
The BCM53115MKFBG can provide a multi-port wired-network front end for an embedded controller, test appliance, or industrial computing platform. Seven integrated Gigabit PHYs create a common switching endpoint for service equipment, test instruments, or local peripherals connected over Ethernet. The system designer should confirm clock sources, firmware requirements, management interfaces, and PHY register configuration before finalizing the architecture. PCB implementation should preserve high-speed signal integrity through short references, appropriate return paths, controlled-impedance differential routing, and dense decoupling around the BGA. Thermal performance should be evaluated with the expected sustained port traffic and the complete enclosure rather than under an isolated-device test condition.
推薦
Network Test Equipment
A seven-port Gigabit switching device is useful in test and measurement equipment that must provide multiple physical network connections for traffic generation, loopback analysis, or endpoint simulation. The BCM53115MKFBG offers seven integrated PHYs in 65 nm LP CMOS, allowing a compact instrument architecture with multiple active copper interfaces. Precise clocking, deterministic startup, port-status monitoring, and reliable thermal operation become important in laboratory and production-test environments. The 400-ball package requires a high-density PCB with validated assembly processes, and the Ethernet media interfaces must be designed for the cable lengths and isolation requirements of the target test environment.
推薦
推薦產品摘要
工程參考資料,適用於 BCM53115MKFBG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | BCM53115MKPBG | BCM53115MKFB | 88E6190X | KSZ9893 | RTL838X |
|---|---|---|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom | Marvell | Microchip Technology | Realtek |
| Package | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA |
| Integrated PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs |
| Ethernet Data Rate | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port |
主要差異化特點
- Seven integrated Gigabit PHYs in one switching device (對比KSZ9893)
- Compact 65 nm LP CMOS implementation (對比RTL838X)
- Exact BCM53115 family continuity (對比88E6190X)
- Seven-port copper Ethernet consolidation (對比KSZ8041TLI-TR)
設計說明
Treat the BCM53115MKFBG as a high-density BGA design. Follow the manufacturer land pattern exactly, provide local supply and ground connections, and route sensitive clock and Ethernet interfaces with continuous reference planes. Verify differential impedance and length rules against the official design guidance rather than relying on generic Ethernet routing conventions. The board should also include a practical assembly stack-up capable of supporting the package's ball pitch and thermal requirements.
Estimate junction temperature from actual 65 nm LP CMOS switching activity, the specified ambient temperature, and copper or heat-spreader performance in the finished enclosure. BGA thermal behavior depends strongly on via arrays, solder-mask and copper-pad design, airflow, and neighboring heat sources. Validate the assembled board with sustained traffic across all seven ports and confirm that the package junction-temperature limit is maintained during worst-case operation.
Keep clock traces short and isolated from noisy switching paths, and use the manufacturer's clocking and decoupling recommendations without increasing trace lengths unnecessarily. Ethernet differential pairs should maintain continuous return paths and controlled impedance through layer transitions. Avoid placing unrelated vias or test points in high-speed regions, and verify edge-rate behavior, crosstalk, and electromagnetic compliance on physical prototypes.
A common mistake is treating a same-family or cross-brand Ethernet IC as interchangeable solely because it is also a multi-port Gigabit switch. Before substituting BCM53115MKPBG, BCM53115MKFB, 88E6190X, KSZ9893, or an RTL838X device, compare the exact ordering suffix, ball map, power rails, clock input, management interface, PHY characteristics, and reference circuitry. An apparent package match does not prove pin-to-pin compatibility.
合規資訊
RoHS compliance is stated in the JLCPCB product result. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current compliance documentation.