BCM53115MKFBG - 7-Port Gigabit Ethernet Switch | Broadcom
부품 번호: BCM53115MKFBG ✓ 활성BCM53115MKFBG 개요
A Gigabit Ethernet switch is a networking semiconductor that forwards Ethernet frames between connected ports while supporting full-duplex communication, auto-negotiation, and traffic management. In the broader hierarchy, it belongs to Ethernet interface ICs, then network interface controllers and switching silicon, and ultimately the semiconductor category. Integrated PHYs reduce the external active Ethernet component count, although magnetics, termination, isolation, and layout requirements still shape the final board design.
The BCM53115MKFBG provides seven Gigabit Ethernet ports, integrated PHYs, 65 nm LP CMOS implementation, and a 400-ball BGA package. Its integration can simplify multi-port equipment compared with a design assembled from several discrete Ethernet interface components. The compact BGA footprint also requires careful PCB routing, thermal analysis, and manufacturing controls because its fine-pitch balls and exposed underside area demand precise layout practices.
The device is applicable to industrial Ethernet switches, router and gateway platforms, broadband access equipment, network surveillance systems, and other multi-port products. For each PHY-facing port, the board must provide the appropriate magnetic interface or supported copper-media interface, power supplies, and controlled-impedance routing. System designers should also validate timing, thermal performance, firmware support, and management features against the Broadcom datasheet and reference designs.
Because the BCM53115MKFBG is a BGA device, layout is a central part of successful implementation. Place decoupling close to the relevant supply pins, keep high-speed traces short, provide adequate reference planes, route differential pairs with controlled impedance, and use an appropriate via field and ball-to-trace transition. PCB assembly should be qualified for the package density and thermal profile used in the finished product.
This page summarizes the verified 7-port Gigabit Ethernet switch identity, records the available package and process information, and identifies practical evaluation points for replacement and hardware design. Detailed electrical limits, register behavior, timing, clock requirements, and absolute maximum ratings should be taken directly from the current Broadcom manufacturer datasheet before schematic release or production qualification.
드롭인 대체품: BCM53115MKFBG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: BCM53115MKFBG (동일 폼 팩터 및 풋프린트).
BCM53115MKPBG
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
BCM53115MKFB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
88E6190X
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
KSZ9893RNXI
✅ 드롭인가격 문의
데이터시트 보기 →RTL838X
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
BCM53115MKFBG 최대 정격 & 전기적 특성
| Product Type | 7-port Gigabit Ethernet switch with integrated PHYs |
| Number of Gigabit Ethernet Ports | 7 ports |
| Integrated PHY Count | 7 integrated Gigabit PHYs |
| Process Technology | 65 nm LP CMOS |
| Package Type | 400-ball BGA, square |
| Number of Terminals | 400 terminals |
| Device Category | Ethernet interface IC / switching IC |
| Ethernet Data Rate | 1 Gb/s per port |
| RoHS 상태 | Compliant |
| 실장 유형 | Surface mount |
BCM53115MKFBG 400-ball bga, square 핀 구성 가이드
BCM53115MKFBG(400-ball bga, square 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: BCM53115MKFBG.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
BCM53115MKFBG 적합 용도: 6 애플리케이션s: Industrial Ethernet Switch, Router and Gateway Platform, Broadband Access Equipment, Network Surveillance System, Embedded Network Controller, Network Test Equipment.
Industrial Ethernet Switch
The BCM53115MKFBG fits industrial Ethernet switch platforms requiring seven Gigabit Ethernet ports in one switching IC. Its seven integrated PHYs provide the physical-layer functions for copper media interfaces while reducing the number of separate transceiver blocks. A board designer must still implement compliant Ethernet magnetics or supported media circuitry, controlled-impedance routing, robust power distribution, and surge protection appropriate to the installation environment. The 400-ball BGA also makes PCB density, via-in-pad decisions, assembly yield, and thermal verification central parts of an industrial design. Before release, verify temperature range, power-loss behavior, recovery features, and management requirements against the manufacturer documentation.
추천
Router and Gateway Platform
A seven-port Gigabit Ethernet arrangement is useful in routers, gateways, and edge appliances where several wired endpoints must connect to a central forwarding engine. The BCM53115MKFBG combines seven Gigabit PHYs with the Ethernet switching function in 65 nm LP CMOS silicon, supporting a compact multi-port architecture. The design must accommodate the required clock, management interface, reset behavior, and power rails while keeping the 400-ball BGA routing orderly. Magnetic components and copper-media compliance remain board-level concerns, and the enclosure, thermal environment, and traffic load should be tested with the intended switch configuration.
추천
Broadband Access Equipment
The BCM53115MKFBG can serve as the seven-port Gigabit switching element in broadband access and customer-premises equipment that aggregates multiple wired connections. Integrated PHYs allow the equipment architect to establish several 1 Gb/s copper-facing ports around one switching device rather than using multiple standalone transceivers. Because access products often depend on strict interoperability and line-card power behavior, the implementation should follow the Broadcom reference design for clocks, decoupling, media interfaces, and thermal construction. Validate boot sequencing, management behavior, fault recovery, and electromagnetic performance in the complete enclosure rather than relying on IC-level simulation alone.
추천
Network Surveillance System
The BCM53115MKFBG is suitable for a networked camera or surveillance controller that needs several Gigabit Ethernet links for cameras, recorders, and uplink equipment. The seven integrated PHYs offer a path to a compact seven-port topology without requiring seven separate multi-port interface blocks. The finished surveillance product must account for cable reach, isolation, surge events, grounding, and power-loss behavior, while the 400-ball BGA needs careful decoupling, thermal relief, and assembly yield management. The seven-port configuration also allows efficient segmentation of cameras and uplinks when the Broadcom management and traffic-control features match the system requirements.
추천
Embedded Network Controller
The BCM53115MKFBG can provide a multi-port wired-network front end for an embedded controller, test appliance, or industrial computing platform. Seven integrated Gigabit PHYs create a common switching endpoint for service equipment, test instruments, or local peripherals connected over Ethernet. The system designer should confirm clock sources, firmware requirements, management interfaces, and PHY register configuration before finalizing the architecture. PCB implementation should preserve high-speed signal integrity through short references, appropriate return paths, controlled-impedance differential routing, and dense decoupling around the BGA. Thermal performance should be evaluated with the expected sustained port traffic and the complete enclosure rather than under an isolated-device test condition.
추천
Network Test Equipment
A seven-port Gigabit switching device is useful in test and measurement equipment that must provide multiple physical network connections for traffic generation, loopback analysis, or endpoint simulation. The BCM53115MKFBG offers seven integrated PHYs in 65 nm LP CMOS, allowing a compact instrument architecture with multiple active copper interfaces. Precise clocking, deterministic startup, port-status monitoring, and reliable thermal operation become important in laboratory and production-test environments. The 400-ball package requires a high-density PCB with validated assembly processes, and the Ethernet media interfaces must be designed for the cable lengths and isolation requirements of the target test environment.
추천
추천 제품 요약
엔지니어링 참조 데이터: BCM53115MKFBG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | BCM53115MKPBG | BCM53115MKFB | 88E6190X | KSZ9893 | RTL838X |
|---|---|---|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom | Marvell | Microchip Technology | Realtek |
| Package | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA | 400-ball BGA |
| Integrated PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | 7 integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs | Integrated Gigabit PHYs |
| Ethernet Data Rate | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port |
주요 차별점
- Seven integrated Gigabit PHYs in one switching device (vs KSZ9893)
- Compact 65 nm LP CMOS implementation (vs RTL838X)
- Exact BCM53115 family continuity (vs 88E6190X)
- Seven-port copper Ethernet consolidation (vs KSZ8041TLI-TR)
설계 노트
Treat the BCM53115MKFBG as a high-density BGA design. Follow the manufacturer land pattern exactly, provide local supply and ground connections, and route sensitive clock and Ethernet interfaces with continuous reference planes. Verify differential impedance and length rules against the official design guidance rather than relying on generic Ethernet routing conventions. The board should also include a practical assembly stack-up capable of supporting the package's ball pitch and thermal requirements.
Estimate junction temperature from actual 65 nm LP CMOS switching activity, the specified ambient temperature, and copper or heat-spreader performance in the finished enclosure. BGA thermal behavior depends strongly on via arrays, solder-mask and copper-pad design, airflow, and neighboring heat sources. Validate the assembled board with sustained traffic across all seven ports and confirm that the package junction-temperature limit is maintained during worst-case operation.
Keep clock traces short and isolated from noisy switching paths, and use the manufacturer's clocking and decoupling recommendations without increasing trace lengths unnecessarily. Ethernet differential pairs should maintain continuous return paths and controlled impedance through layer transitions. Avoid placing unrelated vias or test points in high-speed regions, and verify edge-rate behavior, crosstalk, and electromagnetic compliance on physical prototypes.
A common mistake is treating a same-family or cross-brand Ethernet IC as interchangeable solely because it is also a multi-port Gigabit switch. Before substituting BCM53115MKPBG, BCM53115MKFB, 88E6190X, KSZ9893, or an RTL838X device, compare the exact ordering suffix, ball map, power rails, clock input, management interface, PHY characteristics, and reference circuitry. An apparent package match does not prove pin-to-pin compatibility.
규정 준수 정보
RoHS compliance is stated in the JLCPCB product result. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current compliance documentation.