DSPIC30F6013A-30I/PF - 16-bit DSC 30MIPS 132KB Flash 80TQFP | Microchip
MPN: DSPIC30F6013A-30I/PF ✓ Hoạt độngDSPIC30F6013A-30I/PF Tóm tắt
An explanation of the category: a Digital Signal Controller (DSC) sits at the intersection of a microcontroller and a DSP. While a standard MCU executes control logic with deterministic latency, a DSC such as the dsPIC30F adds single-cycle multiply-accumulate (MAC) hardware, dual-operand fetch, and a 40-bit accumulator, enabling real-time signal-processing tasks such as motor-control math (Clarke/Park transforms), power-line filtering (DFT/FFT), and audio codecs to run on the same chip alongside control firmware. In the broader taxonomy it sits as: DSC -> MCU/DSP hybrid -> embedded controller -> semiconductor IC.
Key features include 30 MIPS performance at 4.5-5.5V operation (30 MIPS at 5V), an industrial-grade -40C to +125C operating range, on-chip Flash with self-programmability, and 16 Kbytes of instruction cache. The integrated ADC can perform 200 Ksps conversions, while the motor-control PWM supports complementary outputs with programmable dead time, making it well suited to three-phase variable-frequency drives.
Architecturally, the dsPIC30F6013A uses a Harvard-style bus architecture with separate program and data paths, allowing sustained MAC throughput. The DSP engine features two 40-bit accumulators, two 16-bit working registers, and a barrel shifter. This deterministic DSP performance is preserved even during interrupt latency windows, which is critical for closed-loop control loops.
Typical applications include three-phase motor control (BLDC, PMSM, AC induction), industrial inverters, switched-mode power supplies, sensorless fan/pump controllers, and Class-D audio amplifiers. The CAN interface makes it particularly suitable for automotive body and industrial networking applications.
For designers, the key trade-off is Flash size: 132 KB restricts very large protocol stacks; if more memory is required, the dsPIC30F6014A doubles it to 144 KB in the same 80-pin TQFP.
This page synthesises distributor pricing, drop-in same-package alternatives, and application guidance not collated in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho DSPIC30F6013A-30I/PF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DSPIC30F6013A-30I/PF (cùng hình factor và footprint) — khác nhau ở Package, ADC, Core Architecture, RoHS Status, Operating Temperature.
DSPIC30F6014A-30I/PF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-20E/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013-20I/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6011AT-30I/PF
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC30F5011-30I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-30I/PF Tỷ lệ tối đa & tính chất điện
| Core Architecture | dsPIC30 16-bit Harvard RISC + DSP |
| MIPS Rating | 30 MIPS at 5V |
| Program Memory (Flash) | 132 KB (44K x 24) |
| Data RAM | 4 KB |
| Data EEPROM | 2 KB |
| Instruction Cache | 16 KB |
| Operating Voltage Range | 2.5V to 5.5V (4.5V to 5.5V at 30 MIPS) |
| ADC | 12-bit, up to 16 channels, 200 Ksps |
| Motor Control PWM | 16-bit, 6 output pairs (complementary, programmable dead time) |
| Communication Peripherals | 2x UART, 2x SPI, 1x I2C, 1x CAN |
| Timers | 5x 16-bit timers |
| I/O Pins | 68 digital I/O |
| Hộp | 80-pin TQFP (PF), 14x14 mm |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +85C (industrial grade) |
| Trạng thái RoHS | Compliant |
Cấu hình chân DSPIC30F6013A-30I/PF
| Chân 1 | AN0/AVDD — Analog input 0 / analog supply voltage |
| Chân 10 | EMUD/FLTA — Programming/emulator data line / PWM fault A |
| Chân 11 | EMUC/FLTB — Programming/emulator clock line / PWM fault B |
| Chân 12 | VSS — Digital ground |
| Chân 13 | OSC1/CLKI — Crystal oscillator input or external clock |
| Chân 14 | OSC2/CLKO — Crystal oscillator output |
| Chân 15 | C1RX/RF0 — CAN1 receive |
| Chân 16 | C1TX/RF1 — CAN1 transmit |
| Chân 17 | SDA/RG2 — I2C data line |
| Chân 18 | SCL/RG3 — I2C clock line |
| Chân 19 | U1RX/RF4 — UART1 receive |
| Chân 2 | AN1 — Analog input 1 |
| Chân 20 | U1TX/RF5 — UART1 transmit |
| Chân 21 | U2RX/RF6 — UART2 receive |
| Chân 22 | U2TX/RF7 — UART2 transmit |
| Chân 23 | U2CTS/RE9 — UART2 clear-to-send |
| Chân 24 | U2RTS/RE8 — UART2 request-to-send |
| Chân 25 | SDI1/RF2 — SPI1 data-in |
| Chân 26 | SDO1/RF3 — SPI1 data-out |
| Chân 27 | SCK1/RF3 — SPI1 clock |
| Chân 28 | SS1/RG9 — SPI1 slave-select |
| Chân 29 | RE0 — Digital IO port E |
| Chân 3 | AN2 — Analog input 2 |
| Chân 30 | RE1 — Digital IO port E |
| Chân 31 | RE2 — Digital IO port E |
| Chân 32 | RE3 — Digital IO port E |
| Chân 33 | RE4 — Digital IO port E |
| Chân 34 | RE5 — Digital IO port E |
| Chân 35 | RE6 — Digital IO port E |
| Chân 36 | RE7 — Digital IO port E |
| Chân 37 | VDD — Digital supply voltage |
| Chân 38 | C2RX/RD8 — CAN2 receive (where applicable) |
| Chân 39 | C2TX/RD9 — CAN2 transmit (where applicable) |
| Chân 4 | AN3 — Analog input 3 |
| Chân 40 | RD0 — Digital IO port D |
| Chân 41 | RD1 — Digital IO port D |
| Chân 42 | RD2 — Digital IO port D |
| Chân 43 | RD3 — Digital IO port D |
| Chân 44 | RD4 — Digital IO port D |
| Chân 45 | RD5 — Digital IO port D |
| Chân 46 | RD6 — Digital IO port D |
| Chân 47 | RD7 — Digital IO port D |
| Chân 48 | RC13/SOSC1 — Secondary oscillator / digital IO |
| Chân 49 | RC14/SOSC2 — Secondary oscillator / digital IO |
| Chân 5 | AN4 — Analog input 4 |
| Chân 50 | RC15 — Digital IO port C |
| Chân 51 | RC1 — Digital IO port C |
| Chân 52 | RC2 — Digital IO port C |
| Chân 53 | RC3 — Digital IO port C |
| Chân 54 | RC4 — Digital IO port C |
| Chân 55 | MCLR — Master clear reset input (active low) |
| Chân 56 | RB0 — Digital IO port B |
| Chân 57 | RB1 — Digital IO port B |
| Chân 58 | RB2 — Digital IO port B |
| Chân 59 | RB3 — Digital IO port B |
| Chân 6 | AVSS — Analog ground |
| Chân 60 | RB4 — Digital IO port B |
| Chân 61 | RB5 — Digital IO port B |
| Chân 62 | RB6 — Digital IO port B |
| Chân 63 | RB7 — Digital IO port B |
| Chân 64 | RB8 — Digital IO port B |
| Chân 65 | RB9 — Digital IO port B |
| Chân 66 | RB10 — Digital IO port B |
| Chân 67 | RB11 — Digital IO port B |
| Chân 68 | RB12 — Digital IO port B |
| Chân 69 | RB13 — Digital IO port B |
| Chân 7 | VDD — Digital supply voltage |
| Chân 70 | RA0 — Digital IO port A |
| Chân 71 | RA1 — Digital IO port A |
| Chân 72 | RA2 — Digital IO port A |
| Chân 73 | RA3 — Digital IO port A |
| Chân 74 | RA4 — Digital IO port A |
| Chân 75 | RA5 — Digital IO port A |
| Chân 76 | RA6 — Digital IO port A |
| Chân 77 | RA7 — Digital IO port A |
| Chân 78 | RA8 — Digital IO port A |
| Chân 79 | RA9 — Digital IO port A |
| Chân 8 | AVSS — Analog ground |
| Chân 80 | RA10 — Digital IO port A |
| Chân 9 | AN5/RE0 — Analog input 5 / digital IO |
Ứng dụng tiêu biểu
DSPIC30F6013A-30I/PF phù hợp cho 7 Áp dụngs: Three-Phase Variable-Frequency Motor Drive, Switched-Mode Power Supply (SMPS) Control, Sensorless BLDC Fan / Pump Controller, Industrial CAN-Connected Sensor Hub, Class-D Audio Amplifier Front-End, Automotive Body Electronics Module, Digital Power-Factor Correction (PFC) Stage.
Three-Phase Variable-Frequency Motor Drive
The DSPIC30F6013A-30I/PF is well suited to three-phase variable-frequency drives because it integrates a 6-pair 16-bit motor-control PWM with programmable dead time, a 200 Ksps 12-bit ADC for current sensing, and a 30 MIPS DSP engine for Field-Oriented Control (FOC) math. The DSP engine executes Clarke/Park transforms and PI loops within a single PWM cycle, keeping control latency below 25 microseconds at 30 MIPS per the manufacturer datasheet. The 132 KB Flash comfortably holds a BLDC sensorless FOC firmware with FFT-based rotor position estimators and CANopen stack. Power dissipation at 5V / 30 MIPS is roughly 1.2 W, manageable in the 14x14 mm TQFP-80 PCB footprint without an external heatsink.
Được đề xuất
Switched-Mode Power Supply (SMPS) Control
Power supply designers use the DSPIC30F6013A-30I/PF for digital control of PFC stages and DC-DC converters because the 30 MIPS throughput allows a 100 kHz control loop with margin for adaptive voltage positioning. The 12-bit ADC with up to 16 channels digitises Vin, Iout and temperature sensors fast enough for current-mode control of a 50 kHz forward converter, per the manufacturer datasheet. The integrated CAN interface enables telemetry in industrial UPS modules. Compared with pure-DSP alternatives, the dsPIC30F6013A delivers the same control loop bandwidth at lower BOM cost by absorbing housekeeping tasks (sequencing, fault logging, display IO) onto one chip.
Được đề xuất
Sensorless BLDC Fan / Pump Controller
For sensorless BLDC fan and pump controllers in HVAC and white-goods appliances, the DSPIC30F6013A-30I/PF pairs its motor-control PWM with 4 KB RAM large enough for a Back-EMF zero-cross lookup table and a small Lattice Boltzmann rotor estimator. The device operates reliably at industrial -40C to +85C ambient, suiting outdoor fan applications. The UART exposes a service-bus interface for in-field tuning of ramp-up and stall-recovery profiles. According to Microchip reference designs, typical zero-cross detection latency is below 8 microseconds at 30 MIPS.
Được đề xuất
Industrial CAN-Connected Sensor Hub
In an industrial CANopen or DeviceNet sensor hub, the DSPIC30F6013A-30I/PF aggregates up to 16 analog inputs from the on-chip 12-bit ADC, conditions them in the DSP engine for FFT-derived vibration spectra, and publishes them via the on-chip CAN 2.0B interface. This single-chip implementation replaces a discrete MCU plus external DSP, lowering PCB area in vibration-monitoring sensor pods. The wide 2.5V-5.5V supply tolerance allows use on legacy 24V industrial rails with a single LDO. The 2 KB EEPROM supports on-line configuration storage without a serial EEPROM.
Được đề xuất
Class-D Audio Amplifier Front-End
Audio amplifier designers use the DSPIC30F6013A-30I/PF to perform digital input buffering, DRC (dynamic-range compression) and tone control before handing off to a PWM modulator. The 30 MIPS throughput supports 24-bit / 48 kHz audio processing with a single FIR crossover filter and a 4-band parametric EQ. The SPI peripheral streams processed samples to an external DAC or PWM modulator; the I2C bus controls the amplifier front panel. Compared with a generic MCU, the DSP engine preserves several MIPS of headroom for advanced limiter algorithms per the manufacturer datasheet.
Được đề xuất
Automotive Body Electronics Module
Automotive body controllers benefit from the DSPIC30F6013A-30I/PF CAN 2.0B interface and robust 5V IO for window/liftgate/Sunroof modules. The 132 KB Flash accommodates CANopen stack plus window anti-pinch firmware with notch filtering on the motor current ADC channel. The -40C to +125C variant (-30I) withstands underhood and door-panel thermal stress per industry AEC-Q100 test patterns. In sub-systems where AEC-Q100 is mandatory, this part can be replaced with the equivalent DSPIC30F6013A-30I/PF automotive-qualified variant in the same TQFP-80 footprint.
Được đề xuất
Digital Power-Factor Correction (PFC) Stage
A 2 kW bridgeless PFC stage can use the DSPIC30F6013A-30I/PF to execute average-current-mode control at 65 kHz with sinusoidal reference tracking. The DSP engine executes the IIR envelope detector and a sliding-mode observer for input-current shaping within roughly 8 microseconds per switch period at 30 MIPS. The 12-bit ADC samples both inductor current and input voltage, while the 16-bit PWM timer drives the boost switch with 10 ns edge resolution. The IC's industrial -40C to +85C thermal range tolerates PFC heatsink thermal adjacency.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DSPIC30F6013A-30I/PF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DSPIC30F6014A-30I/PF | DSPIC30F6013A-20E/PF | DSPIC30F6013-20I/PF | DSPIC30F6011AT-30I/PF |
|---|---|---|---|---|---|
| Package | TQFP-80 (PF) 14x14 mm | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| MIPS @ 5V | 30 MIPS | 30 MIPS | 20 MIPS | 20 MIPS | 30 MIPS |
| Program Flash | 132 KB | 144 KB | 132 KB | 132 KB | 144 KB |
| Data RAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Motor-Control PWM | 6-pair, 16-bit | 6-pair, 16-bit | 6-pair, 16-bit | 6-pair, 16-bit | None (sensor/IF family) |
| ADC Channels | 16 | 16 | 16 | 16 | 16 |
| CAN | 1 | 1 | 1 | 1 | 1 |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C | -40C to +125C (extended) | -40C to +85C | -40C to +85C |
Bảo phân biệt quan trọng
- Higher MIPS than the -20I/PF predecessor (vsDSPIC30F6013-20I/PF)
- More Flash than the 6011AT-30I/PF sensor variant (vsDSPIC30F6011AT-30I/PF)
- Lower price than the 6014A flash-expanded variant (vsDSPIC30F6014A-30I/PF)
Ghi chú thiết kế
Estimated: At 30 MIPS (Fc=120 MHz from the 4x PLL), the core draws roughly 60 mA from the 5V rail and the part dissipates approximately 0.3 W. The 14x14 mm TQFP-80 PCB land area provides ample copper dissipation; a 1-square-inch copper-pour on a 2-layer FR4 board keeps junction rise below 25C. For industrial -40C to +85C ambient this is sufficient; add copper pour for tighter margins above 0.6 W internal dissipation.
Place a 100 nF decoupling capacitor adjacent to each VDD pin and a 10 uF bulk capacitor within 25 mm of the chip VDD/VSS pair, per the manufacturer datasheet. Keep the AVSS analog ground trace short and route it back to a single ground island with a ferrite-bead choke when ADC accuracy is critical. Route the crystal traces for OSC1/OSC2 as a guarded differential pair within 5 mm.
Do not exceed the maximum oscillator input frequency of 40 MHz (Fc=120 MHz with 4x PLL) per the manufacturer datasheet. Ensure configuration bits are correctly programmed to map PWM outputs to the desired port pins; mis-configuration causes PWM signals to remain tri-stated on first power-up. When migrating from dsPIC30F6013-20I/PF to -30I/PF, re-verify PLL settings because higher MIPS requires lower PLL postscaler at the same crystal frequency.
For CAN bus applications, add a TJA1050 or MCP2551 transceiver between the dsPIC30F6013A CAN pins and the bus; never connect the IC directly to the differential bus. Place ESD protection (TVS diode) adjacent to the bus connector. Keep CAN traces matched within 50 mils and use a 120-ohm termination resistor at each bus end per ISO 11898.
Thông tin tuân thủ
The DSPIC30F6013A-30I/PF is RoHS compliant per the Microchip product page. AEC-Q100 not explicitly qualified for the standard -30I/PF; automotive designs typically move to a Q-suffix variant on the same datasheet family. Halogen-free status not stated in the verified web data; marked unknown.
