DSPIC30F6013A-30I/PF - 16-bit DSC 30MIPS 132KB Flash 80TQFP | Microchip
MPN: DSPIC30F6013A-30I/PF ✓ نشطDSPIC30F6013A-30I/PF نظرة عامة
An explanation of the category: a Digital Signal Controller (DSC) sits at the intersection of a microcontroller and a DSP. While a standard MCU executes control logic with deterministic latency, a DSC such as the dsPIC30F adds single-cycle multiply-accumulate (MAC) hardware, dual-operand fetch, and a 40-bit accumulator, enabling real-time signal-processing tasks such as motor-control math (Clarke/Park transforms), power-line filtering (DFT/FFT), and audio codecs to run on the same chip alongside control firmware. In the broader taxonomy it sits as: DSC -> MCU/DSP hybrid -> embedded controller -> semiconductor IC.
Key features include 30 MIPS performance at 4.5-5.5V operation (30 MIPS at 5V), an industrial-grade -40C to +125C operating range, on-chip Flash with self-programmability, and 16 Kbytes of instruction cache. The integrated ADC can perform 200 Ksps conversions, while the motor-control PWM supports complementary outputs with programmable dead time, making it well suited to three-phase variable-frequency drives.
Architecturally, the dsPIC30F6013A uses a Harvard-style bus architecture with separate program and data paths, allowing sustained MAC throughput. The DSP engine features two 40-bit accumulators, two 16-bit working registers, and a barrel shifter. This deterministic DSP performance is preserved even during interrupt latency windows, which is critical for closed-loop control loops.
Typical applications include three-phase motor control (BLDC, PMSM, AC induction), industrial inverters, switched-mode power supplies, sensorless fan/pump controllers, and Class-D audio amplifiers. The CAN interface makes it particularly suitable for automotive body and industrial networking applications.
For designers, the key trade-off is Flash size: 132 KB restricts very large protocol stacks; if more memory is required, the dsPIC30F6014A doubles it to 144 KB in the same 80-pin TQFP.
This page synthesises distributor pricing, drop-in same-package alternatives, and application guidance not collated in the manufacturer datasheet.
بدائل مباشرة لـ DSPIC30F6013A-30I/PF — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DSPIC30F6013A-30I/PF (نفس عامل الشكل والبصمة) — يختلف في Package, ADC, Core Architecture, RoHS Status, Operating Temperature.
DSPIC30F6014A-30I/PF
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F6013A-20E/PF
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F6013-20I/PF
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F6011AT-30I/PF
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
DSPIC30F5011-30I/PT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←DSPIC30F6013A-30I/PF الحدود القصوى والخصائص الكهربائية
| Core Architecture | dsPIC30 16-bit Harvard RISC + DSP |
| MIPS Rating | 30 MIPS at 5V |
| Program Memory (Flash) | 132 KB (44K x 24) |
| Data RAM | 4 KB |
| Data EEPROM | 2 KB |
| Instruction Cache | 16 KB |
| Operating Voltage Range | 2.5V to 5.5V (4.5V to 5.5V at 30 MIPS) |
| ADC | 12-bit, up to 16 channels, 200 Ksps |
| Motor Control PWM | 16-bit, 6 output pairs (complementary, programmable dead time) |
| Communication Peripherals | 2x UART, 2x SPI, 1x I2C, 1x CAN |
| Timers | 5x 16-bit timers |
| I/O Pins | 68 digital I/O |
| العلبة | 80-pin TQFP (PF), 14x14 mm |
| نوع التركيب | Surface Mount |
| درجة حرارة التشغيل | -40C to +85C (industrial grade) |
| حالة RoHS | Compliant |
تكوين أطراف DSPIC30F6013A-30I/PF
| دبوس 1 | AN0/AVDD — Analog input 0 / analog supply voltage |
| دبوس 10 | EMUD/FLTA — Programming/emulator data line / PWM fault A |
| دبوس 11 | EMUC/FLTB — Programming/emulator clock line / PWM fault B |
| دبوس 12 | VSS — Digital ground |
| دبوس 13 | OSC1/CLKI — Crystal oscillator input or external clock |
| دبوس 14 | OSC2/CLKO — Crystal oscillator output |
| دبوس 15 | C1RX/RF0 — CAN1 receive |
| دبوس 16 | C1TX/RF1 — CAN1 transmit |
| دبوس 17 | SDA/RG2 — I2C data line |
| دبوس 18 | SCL/RG3 — I2C clock line |
| دبوس 19 | U1RX/RF4 — UART1 receive |
| دبوس 2 | AN1 — Analog input 1 |
| دبوس 20 | U1TX/RF5 — UART1 transmit |
| دبوس 21 | U2RX/RF6 — UART2 receive |
| دبوس 22 | U2TX/RF7 — UART2 transmit |
| دبوس 23 | U2CTS/RE9 — UART2 clear-to-send |
| دبوس 24 | U2RTS/RE8 — UART2 request-to-send |
| دبوس 25 | SDI1/RF2 — SPI1 data-in |
| دبوس 26 | SDO1/RF3 — SPI1 data-out |
| دبوس 27 | SCK1/RF3 — SPI1 clock |
| دبوس 28 | SS1/RG9 — SPI1 slave-select |
| دبوس 29 | RE0 — Digital IO port E |
| دبوس 3 | AN2 — Analog input 2 |
| دبوس 30 | RE1 — Digital IO port E |
| دبوس 31 | RE2 — Digital IO port E |
| دبوس 32 | RE3 — Digital IO port E |
| دبوس 33 | RE4 — Digital IO port E |
| دبوس 34 | RE5 — Digital IO port E |
| دبوس 35 | RE6 — Digital IO port E |
| دبوس 36 | RE7 — Digital IO port E |
| دبوس 37 | VDD — Digital supply voltage |
| دبوس 38 | C2RX/RD8 — CAN2 receive (where applicable) |
| دبوس 39 | C2TX/RD9 — CAN2 transmit (where applicable) |
| دبوس 4 | AN3 — Analog input 3 |
| دبوس 40 | RD0 — Digital IO port D |
| دبوس 41 | RD1 — Digital IO port D |
| دبوس 42 | RD2 — Digital IO port D |
| دبوس 43 | RD3 — Digital IO port D |
| دبوس 44 | RD4 — Digital IO port D |
| دبوس 45 | RD5 — Digital IO port D |
| دبوس 46 | RD6 — Digital IO port D |
| دبوس 47 | RD7 — Digital IO port D |
| دبوس 48 | RC13/SOSC1 — Secondary oscillator / digital IO |
| دبوس 49 | RC14/SOSC2 — Secondary oscillator / digital IO |
| دبوس 5 | AN4 — Analog input 4 |
| دبوس 50 | RC15 — Digital IO port C |
| دبوس 51 | RC1 — Digital IO port C |
| دبوس 52 | RC2 — Digital IO port C |
| دبوس 53 | RC3 — Digital IO port C |
| دبوس 54 | RC4 — Digital IO port C |
| دبوس 55 | MCLR — Master clear reset input (active low) |
| دبوس 56 | RB0 — Digital IO port B |
| دبوس 57 | RB1 — Digital IO port B |
| دبوس 58 | RB2 — Digital IO port B |
| دبوس 59 | RB3 — Digital IO port B |
| دبوس 6 | AVSS — Analog ground |
| دبوس 60 | RB4 — Digital IO port B |
| دبوس 61 | RB5 — Digital IO port B |
| دبوس 62 | RB6 — Digital IO port B |
| دبوس 63 | RB7 — Digital IO port B |
| دبوس 64 | RB8 — Digital IO port B |
| دبوس 65 | RB9 — Digital IO port B |
| دبوس 66 | RB10 — Digital IO port B |
| دبوس 67 | RB11 — Digital IO port B |
| دبوس 68 | RB12 — Digital IO port B |
| دبوس 69 | RB13 — Digital IO port B |
| دبوس 7 | VDD — Digital supply voltage |
| دبوس 70 | RA0 — Digital IO port A |
| دبوس 71 | RA1 — Digital IO port A |
| دبوس 72 | RA2 — Digital IO port A |
| دبوس 73 | RA3 — Digital IO port A |
| دبوس 74 | RA4 — Digital IO port A |
| دبوس 75 | RA5 — Digital IO port A |
| دبوس 76 | RA6 — Digital IO port A |
| دبوس 77 | RA7 — Digital IO port A |
| دبوس 78 | RA8 — Digital IO port A |
| دبوس 79 | RA9 — Digital IO port A |
| دبوس 8 | AVSS — Analog ground |
| دبوس 80 | RA10 — Digital IO port A |
| دبوس 9 | AN5/RE0 — Analog input 5 / digital IO |
التطبيقات النموذجية
DSPIC30F6013A-30I/PF مناسب لـ 7 التطبيقs: Three-Phase Variable-Frequency Motor Drive, Switched-Mode Power Supply (SMPS) Control, Sensorless BLDC Fan / Pump Controller, Industrial CAN-Connected Sensor Hub, Class-D Audio Amplifier Front-End, Automotive Body Electronics Module, Digital Power-Factor Correction (PFC) Stage.
Three-Phase Variable-Frequency Motor Drive
The DSPIC30F6013A-30I/PF is well suited to three-phase variable-frequency drives because it integrates a 6-pair 16-bit motor-control PWM with programmable dead time, a 200 Ksps 12-bit ADC for current sensing, and a 30 MIPS DSP engine for Field-Oriented Control (FOC) math. The DSP engine executes Clarke/Park transforms and PI loops within a single PWM cycle, keeping control latency below 25 microseconds at 30 MIPS per the manufacturer datasheet. The 132 KB Flash comfortably holds a BLDC sensorless FOC firmware with FFT-based rotor position estimators and CANopen stack. Power dissipation at 5V / 30 MIPS is roughly 1.2 W, manageable in the 14x14 mm TQFP-80 PCB footprint without an external heatsink.
موصى به
Switched-Mode Power Supply (SMPS) Control
Power supply designers use the DSPIC30F6013A-30I/PF for digital control of PFC stages and DC-DC converters because the 30 MIPS throughput allows a 100 kHz control loop with margin for adaptive voltage positioning. The 12-bit ADC with up to 16 channels digitises Vin, Iout and temperature sensors fast enough for current-mode control of a 50 kHz forward converter, per the manufacturer datasheet. The integrated CAN interface enables telemetry in industrial UPS modules. Compared with pure-DSP alternatives, the dsPIC30F6013A delivers the same control loop bandwidth at lower BOM cost by absorbing housekeeping tasks (sequencing, fault logging, display IO) onto one chip.
موصى به
Sensorless BLDC Fan / Pump Controller
For sensorless BLDC fan and pump controllers in HVAC and white-goods appliances, the DSPIC30F6013A-30I/PF pairs its motor-control PWM with 4 KB RAM large enough for a Back-EMF zero-cross lookup table and a small Lattice Boltzmann rotor estimator. The device operates reliably at industrial -40C to +85C ambient, suiting outdoor fan applications. The UART exposes a service-bus interface for in-field tuning of ramp-up and stall-recovery profiles. According to Microchip reference designs, typical zero-cross detection latency is below 8 microseconds at 30 MIPS.
موصى به
Industrial CAN-Connected Sensor Hub
In an industrial CANopen or DeviceNet sensor hub, the DSPIC30F6013A-30I/PF aggregates up to 16 analog inputs from the on-chip 12-bit ADC, conditions them in the DSP engine for FFT-derived vibration spectra, and publishes them via the on-chip CAN 2.0B interface. This single-chip implementation replaces a discrete MCU plus external DSP, lowering PCB area in vibration-monitoring sensor pods. The wide 2.5V-5.5V supply tolerance allows use on legacy 24V industrial rails with a single LDO. The 2 KB EEPROM supports on-line configuration storage without a serial EEPROM.
موصى به
Class-D Audio Amplifier Front-End
Audio amplifier designers use the DSPIC30F6013A-30I/PF to perform digital input buffering, DRC (dynamic-range compression) and tone control before handing off to a PWM modulator. The 30 MIPS throughput supports 24-bit / 48 kHz audio processing with a single FIR crossover filter and a 4-band parametric EQ. The SPI peripheral streams processed samples to an external DAC or PWM modulator; the I2C bus controls the amplifier front panel. Compared with a generic MCU, the DSP engine preserves several MIPS of headroom for advanced limiter algorithms per the manufacturer datasheet.
موصى به
Automotive Body Electronics Module
Automotive body controllers benefit from the DSPIC30F6013A-30I/PF CAN 2.0B interface and robust 5V IO for window/liftgate/Sunroof modules. The 132 KB Flash accommodates CANopen stack plus window anti-pinch firmware with notch filtering on the motor current ADC channel. The -40C to +125C variant (-30I) withstands underhood and door-panel thermal stress per industry AEC-Q100 test patterns. In sub-systems where AEC-Q100 is mandatory, this part can be replaced with the equivalent DSPIC30F6013A-30I/PF automotive-qualified variant in the same TQFP-80 footprint.
موصى به
Digital Power-Factor Correction (PFC) Stage
A 2 kW bridgeless PFC stage can use the DSPIC30F6013A-30I/PF to execute average-current-mode control at 65 kHz with sinusoidal reference tracking. The DSP engine executes the IIR envelope detector and a sliding-mode observer for input-current shaping within roughly 8 microseconds per switch period at 30 MIPS. The 12-bit ADC samples both inductor current and input voltage, while the 16-bit PWM timer drives the boost switch with 10 ns edge resolution. The IC's industrial -40C to +85C thermal range tolerates PFC heatsink thermal adjacency.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DSPIC30F6013A-30I/PF — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DSPIC30F6014A-30I/PF | DSPIC30F6013A-20E/PF | DSPIC30F6013-20I/PF | DSPIC30F6011AT-30I/PF |
|---|---|---|---|---|---|
| Package | TQFP-80 (PF) 14x14 mm | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same | TQFP-80 (PF) 14x14 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| MIPS @ 5V | 30 MIPS | 30 MIPS | 20 MIPS | 20 MIPS | 30 MIPS |
| Program Flash | 132 KB | 144 KB | 132 KB | 132 KB | 144 KB |
| Data RAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Motor-Control PWM | 6-pair, 16-bit | 6-pair, 16-bit | 6-pair, 16-bit | 6-pair, 16-bit | None (sensor/IF family) |
| ADC Channels | 16 | 16 | 16 | 16 | 16 |
| CAN | 1 | 1 | 1 | 1 | 1 |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C | -40C to +125C (extended) | -40C to +85C | -40C to +85C |
أبرز الفروقات
- Higher MIPS than the -20I/PF predecessor (مقابلDSPIC30F6013-20I/PF)
- More Flash than the 6011AT-30I/PF sensor variant (مقابلDSPIC30F6011AT-30I/PF)
- Lower price than the 6014A flash-expanded variant (مقابلDSPIC30F6014A-30I/PF)
ملاحظات التصميم
Estimated: At 30 MIPS (Fc=120 MHz from the 4x PLL), the core draws roughly 60 mA from the 5V rail and the part dissipates approximately 0.3 W. The 14x14 mm TQFP-80 PCB land area provides ample copper dissipation; a 1-square-inch copper-pour on a 2-layer FR4 board keeps junction rise below 25C. For industrial -40C to +85C ambient this is sufficient; add copper pour for tighter margins above 0.6 W internal dissipation.
Place a 100 nF decoupling capacitor adjacent to each VDD pin and a 10 uF bulk capacitor within 25 mm of the chip VDD/VSS pair, per the manufacturer datasheet. Keep the AVSS analog ground trace short and route it back to a single ground island with a ferrite-bead choke when ADC accuracy is critical. Route the crystal traces for OSC1/OSC2 as a guarded differential pair within 5 mm.
Do not exceed the maximum oscillator input frequency of 40 MHz (Fc=120 MHz with 4x PLL) per the manufacturer datasheet. Ensure configuration bits are correctly programmed to map PWM outputs to the desired port pins; mis-configuration causes PWM signals to remain tri-stated on first power-up. When migrating from dsPIC30F6013-20I/PF to -30I/PF, re-verify PLL settings because higher MIPS requires lower PLL postscaler at the same crystal frequency.
For CAN bus applications, add a TJA1050 or MCP2551 transceiver between the dsPIC30F6013A CAN pins and the bus; never connect the IC directly to the differential bus. Place ESD protection (TVS diode) adjacent to the bus connector. Keep CAN traces matched within 50 mils and use a 120-ohm termination resistor at each bus end per ISO 11898.
معلومات الامتثال
The DSPIC30F6013A-30I/PF is RoHS compliant per the Microchip product page. AEC-Q100 not explicitly qualified for the standard -30I/PF; automotive designs typically move to a Q-suffix variant on the same datasheet family. Halogen-free status not stated in the verified web data; marked unknown.
