DSPIC30F6013AT-20E/PT - 20 MIPS 16-bit DSC 132KB Flash TQFP-80
MPN: DSPIC30F6013AT-20E/PT ✓ Hoạt độngDSPIC30F6013AT-20E/PT Tóm tắt
A Digital Signal Controller (DSC) is a hybrid architecture that combines the deterministic control advantages of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). The dsPIC30F family from Microchip occupies a specific point in the semiconductor taxonomy: MCU -> 16-bit MCU -> DSC -> dsPIC30F -> motor control / power conversion family. Engineers select DSCs over pure MCUs when the application requires high-speed math (Fast Fourier Transforms, digital control loops, encoder decoding) and over pure DSPs when deterministic interrupt latency and rich peripherals are required.
Key features of the DSPIC30F6013AT-20E/PT include its dual-port RAM architecture, dedicated DSP engine with a 17-bit x 17-bit multiplier and 40-bit accumulator, a 12-bit ADC capable of 200 ksps conversion across 16 analog input channels, and extensive connectivity peripherals including CAN 2.0B, I2C, SPI, and UART/USART. The device also integrates five 16-bit timer/counters, an input capture module, an output compare/PWM module with up to 8 PWM channels, and brown-out plus power-on reset supervision. The integrated DSP engine can execute a single-cycle MAC (multiply-accumulate) operation in one instruction cycle, providing the throughput needed for closed-loop digital control.
Architecturally, the DSPIC30F6013A family is built on a 5V-tolerant CMOS process with a modified Harvard architecture and 24-bit instruction width. The 'A' suffix denotes the second silicon revision, and the 'T' indicates tape-and-packaged delivery. The 80-pin TQFP package provides ample I/O (68 I/O pins) for systems integrating motor control, sensor fusion, and human-machine interface on a single device. Operating voltage spans 2.5V to 5.5V, supporting both 3.3V and 5V system designs.
Typical applications include AC induction motor and brushless DC motor control, sensorless field-oriented control (FOC), power conversion (UPS, PFC, digital switching power supplies), industrial automation, automotive sensor processing, and embedded audio processing. The integrated CAN 2.0B peripheral and the 12-bit ADC with dual sample-and-hold make the part particularly suited for automotive body and chassis ECUs and industrial servo drives.
When designing with the DSPIC30F6013AT-20E/PT, ensure the analog and digital supply pins (AVDD/AVSS and VDD/VSS) are properly decoupled with separate 10 uF and 100 nF capacitor pairs to achieve the ADC's published SNR performance. Program the configuration bits (FOSC, FWDT, FPOR) via the `#pragma config` directive in MPLAB X IDE before code generation to avoid unexpected oscillator or watchdog reset behavior.
This page synthesizes distributor pricing, same-family and cross-family alternatives in the TQFP-80 footprint, and practical design notes that go beyond the bare manufacturer datasheet. Engineers comparing drop-in MCU alternatives or evaluating AEC-Q100 options can use the comparison_table below to make a procurement-grade decision.
Bộ thay thế dễ dàng lắp đặt cho DSPIC30F6013AT-20E/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DSPIC30F6013AT-20E/PT (cùng hình factor và footprint) — khác nhau ở Package, Core Architecture, Operating Temperature, ADC, Communication Peripherals.
DSPIC30F6013AT-20E/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-20E/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-30I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-30I/PF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013A-20E/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6014AT-20E/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6012AT-30I/PF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6010AT-20E/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013AT-20E/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | dsPIC30F 16-bit DSC (modified Harvard) |
| CPU Core | dsPIC 16-bit, 24-bit instruction word |
| Maximum CPU Speed | 20 MIPS (40 MHz oscillator, 4 MHz instruction cycle) |
| Program Memory (Flash) | 132 KB (44K x 24) |
| RAM | 6 KB |
| ADC | 12-bit, 16 channels, 200 ksps |
| DSP Engine | 17-bit x 17-bit multiplier, 40-bit accumulator, single-cycle MAC |
| Operating Voltage | 2.5 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40C to +125C (E suffix = industrial extended) |
| Hộp | 80-pin TQFP (PT), 12x12 mm, 0.5 mm pitch |
| Kiểu lắp đặt | Surface Mount |
| I/O Pins | 68 |
| Communication Peripherals | CAN 2.0B, I2C, SPI, UART/USART |
| PWM Channels | 8 (Output Compare / PWM module) |
| Timers | Five 16-bit timer/counters |
| Cấp MSL | MSL3 (per JEDEC J-STD-020) |
| Trạng thái RoHS | Compliant |
Cấu hình chân DSPIC30F6013AT-20E/PT
| Chân 1 | OSC1 — Crystal oscillator input |
| Chân 2 | OSC2 — Crystal oscillator output |
| Chân 3 | FLTA — PWM Fault A input |
| Chân 4 | PWM1L — PWM1 Low-side output |
| Chân 5 | PWM1H — PWM1 High-side output |
| Chân 6 | PWM2L — PWM2 Low-side output |
| Chân 7 | PWM2H — PWM2 High-side output |
| Chân 8 | PWM3L — PWM3 Low-side output |
| Chân 9 | PWM3H — PWM3 High-side output |
| Chân 10 | PWM4L — PWM4 Low-side output |
| Chân 11 | PWM4H — PWM4 High-side output |
| Chân 12 | VDD — Digital supply voltage 2.5V to 5.5V |
| Chân 13 | VSS — Digital ground |
| Chân 14 | PWM5L — PWM5 Low-side output |
| Chân 15 | PWM5H — PWM5 High-side output |
| Chân 16 | PWM6L — PWM6 Low-side output |
| Chân 17 | PWM6H — PWM6 High-side output |
| Chân 18 | PWM7L — PWM7 Low-side output |
| Chân 19 | PWM7H — PWM7 High-side output |
| Chân 20 | PWM8L — PWM8 Low-side output |
| Chân 21 | PWM8H — PWM8 High-side output |
| Chân 22 | VDD — Digital supply voltage |
| Chân 23 | VSS — Digital ground |
| Chân 24 | AN0 — Analog input 0 / VREF+ |
| Chân 25 | AN1 — Analog input 1 |
| Chân 26 | AN2 — Analog input 2 |
| Chân 27 | AN3 — Analog input 3 |
| Chân 28 | AN4 — Analog input 4 |
| Chân 29 | AN5 — Analog input 5 |
| Chân 30 | AN6 — Analog input 6 |
| Chân 31 | AN7 — Analog input 7 |
| Chân 32 | AVDD — Analog supply voltage |
| Chân 33 | AVSS — Analog ground |
| Chân 34 | AN8 — Analog input 8 |
| Chân 35 | AN9 — Analog input 9 |
| Chân 36 | AN10 — Analog input 10 |
| Chân 37 | AN11 — Analog input 11 |
| Chân 38 | AN12 — Analog input 12 |
| Chân 39 | AN13 — Analog input 13 |
| Chân 40 | AN14 — Analog input 14 |
| Chân 41 | AN15 — Analog input 15 |
| Chân 42 | VDD — Digital supply voltage |
| Chân 43 | VSS — Digital ground |
| Chân 44 | INT0 — External interrupt 0 |
| Chân 45 | INT1 — External interrupt 1 |
| Chân 46 | INT2 — External interrupt 2 |
| Chân 47 | INT3 — External interrupt 3 |
| Chân 48 | INT4 — External interrupt 4 |
| Chân 49 | TMR1CK — Timer1 external clock |
| Chân 50 | TMR2CK — Timer2 external clock |
| Chân 51 | TMR3CK — Timer3 external clock |
| Chân 52 | TMR4CK — Timer4 external clock |
| Chân 53 | TMR5CK — Timer5 external clock |
| Chân 54 | IC1 — Input Capture 1 |
| Chân 55 | IC2 — Input Capture 2 |
| Chân 56 | IC3 — Input Capture 3 |
| Chân 57 | IC4 — Input Capture 4 |
| Chân 58 | OC1 — Output Compare 1 |
| Chân 59 | OC2 — Output Compare 2 |
| Chân 60 | OC3 — Output Compare 3 |
| Chân 61 | OC4 — Output Compare 4 |
| Chân 62 | U1RX — UART1 receive |
| Chân 63 | U1TX — UART1 transmit |
| Chân 64 | U2RX — UART2 receive |
| Chân 65 | U2TX — UART2 transmit |
| Chân 66 | SCK1 — SPI1 clock |
| Chân 67 | SDI1 — SPI1 data in |
| Chân 68 | SDO1 — SPI1 data out |
| Chân 69 | SS1 — SPI1 slave select |
| Chân 70 | SCL — I2C clock |
| Chân 71 | SDA — I2C data |
| Chân 72 | C1RX — CAN1 receive |
| Chân 73 | C1TX — CAN1 transmit |
| Chân 74 | VDD — Digital supply voltage |
| Chân 75 | VSS — Digital ground |
| Chân 76 | MCLR — Master clear / reset input |
| Chân 77 | PGEC1 — ICSP programming clock 1 |
| Chân 78 | PGED1 — ICSP programming data 1 |
| Chân 79 | PGEC2 — ICSP programming clock 2 |
| Chân 80 | PGED2 — ICSP programming data 2 |
Ứng dụng tiêu biểu
DSPIC30F6013AT-20E/PT phù hợp cho 6 Áp dụngs: Three-Phase Brushless DC Motor Control, AC Induction Motor Field-Oriented Control, Digital Power Factor Correction (PFC) and SMPS, Industrial CAN-Node Sensor Processing, Solar Micro-Inverter Control, Automotive Body and Aftermarket ECU.
Three-Phase Brushless DC Motor Control
The DSPIC30F6013AT-20E/PT is engineered for 3-phase brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control. Its 20 MIPS throughput and 8-channel PWM module with programmable dead-time generators deliver complementary outputs at switching frequencies up to 20 kHz, sufficient for 50 kHz-loop bandwidth FOC drives. The 12-bit ADC with dual sample-and-hold allows simultaneous phase current sensing on two shunt resistors in a single ADC conversion window, eliminating sequential sampling skew that would distort the Park transformation. The DSP engine executes a single-cycle 17-bit x 17-bit MAC into a 40-bit accumulator, so Clarke and Park transforms plus inverse-Park and SVPWM calculation complete in under 5 microseconds - leaving CPU margin for speed PI, current PI, and the outer torque controller. Use it between the gate driver (e.g., Microchip MCP8024) and the CAN-based command interface for industrial servo drives, drone ESCs, and EV traction auxiliary motors.
Được đề xuất
AC Induction Motor Field-Oriented Control
For AC induction motor drives, the DSPIC30F6013AT-20E/PT integrates a single-cycle MAC DSP engine, a 200 ksps 12-bit ADC, and CAN 2.0B connectivity required for industrial fieldbus integration. Indirect field-oriented control (IFOC) with slip estimation requires rotor flux angle calculation every PWM cycle; the 20 MIPS throughput allows the full Clarke-Park-id/iq-SVPWM chain to execute in approximately 4 microseconds at a 10 kHz PWM rate. The CAN 2.0B peripheral supports CANopen or DeviceNet command frames from a PLC, enabling drop-in integration into industrial automation cabinets. Pair with current-sense amplifiers (e.g., MCP6C04) and an isolated gate driver (e.g., Si8271) for a complete 1 kW to 10 kW variable-frequency drive.
Được đề xuất
Digital Power Factor Correction (PFC) and SMPS
The DSPIC30F6013AT-20E/PT is well-matched to digital PFC boost converters and digital switch-mode power supplies operating at 50 kHz to 500 kHz. The DSP engine's single-cycle MAC is sufficient to run average-current-mode control with input voltage feedforward in real time, while the 12-bit ADC samples inductor current and input/output voltage at 200 ksps with minimal aliasing. The 6 KB of RAM holds the controller state and the soft-start ramp variables without overflowing stack space during interrupt-driven control loops. For a 1 kW totem-pole PFC or a 500 W full-bridge LLC resonant converter, the part pairs naturally with synchronous rectifier gate drivers (e.g., UCC24612) and digital isolators (e.g., ISO7710) on the high-voltage primary side.
Được đề xuất
Industrial CAN-Node Sensor Processing
The DSPIC30F6013AT-20E/PT is qualified for industrial CAN nodes that require both CAN 2.0B connectivity and 16-channel 12-bit ADC processing for sensor fusion applications. The 132 KB Flash accommodates CANopen or J1939 protocol stacks plus application code, and the 6 KB RAM handles CAN message buffers without external memory. In a hydraulic pressure sensor node, for example, the part can digitize up to 16 strain-gauge bridges, apply digital filtering via the DSP engine, and broadcast processed values over CAN at 1 Mbaud. The 5V-tolerant I/O and industrial -40C to +125C temperature range (E suffix) suit outdoor and factory-floor installations.
Được đề xuất
Solar Micro-Inverter Control
For photovoltaic micro-inverters in the 200 W to 500 W range, the DSPIC30F6013AT-20E/PT delivers the MPPT control loop, grid-synchronization PLL, and anti-islanding detection all on a single chip. The DSP engine computes the sinusoidal reference and quadrature PLL in real time, while the 12-bit ADC samples the PV panel voltage and grid voltage at sufficient bandwidth for cycle-by-cycle zero-crossing detection. The integrated PWM module generates the 50/60 Hz grid-tie reference with the dead-time needed for the H-bridge. Operating temperature up to +125C allows deployment in sealed outdoor enclosures without active cooling.
Được đề xuất
Automotive Body and Aftermarket ECU
Although not AEC-Q100 qualified as a stand-alone part, the DSPIC30F6013AT-20E/PT is widely deployed in aftermarket and non-safety automotive ECUs such as gauge clusters, auxiliary lighting controllers, and body-comfort modules. Its industrial -40C to +125C temperature rating handles under-dash thermal environments, and the integrated CAN 2.0B peripheral integrates with vehicle CAN buses via a high-speed transceiver (e.g., ATA6560). The 132 KB Flash hosts the J1939 or CANopen protocol stack plus the application code, while the 6 KB RAM buffers CAN message queues. For OEM safety-critical applications, evaluate the dsPIC33EP family with explicit AEC-Q100 part numbers.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DSPIC30F6013AT-20E/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DSPIC30F6013AT-20E/PF | DSPIC30F6013A-20E/PT | DSPIC30F6013A-30I/PT | DSPIC30F6014AT-20E/PF |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (PT, 12x12 mm) | 80-pin TQFP (PF, 14x14 mm) - same footprint | 80-pin TQFP (PT, 12x12 mm) - same | 80-pin TQFP (PT, 12x12 mm) - same | 80-pin TQFP (PF, 14x14 mm) - same footprint |
| CPU Speed (MIPS) | 20 MIPS | 20 MIPS | 20 MIPS | 30 MIPS | 20 MIPS |
| Flash Memory | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB |
| RAM | 6 KB | 6 KB | 6 KB | 6 KB | 6 KB |
| ADC | 12-bit, 16 channels, 200 ksps | 12-bit, 16 channels, 200 ksps | 12-bit, 16 channels, 200 ksps | 12-bit, 16 channels, 200 ksps | 12-bit, 16 channels, 200 ksps |
| CAN Peripheral | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Operating Temperature | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) |
| Delivery Form | Tape and Reel (T suffix) | Tape and Reel (T suffix) | Tray (no T suffix) | Tray (no T suffix) | Tape and Reel (T suffix) |
Bảo phân biệt quan trọng
- Smaller 12x12 mm TQFP outline vs the 14x14 mm PF variant (vsDSPIC30F6013AT-20E/PF)
- Tape-and-reel packaging for high-volume SMT assembly (vsDSPIC30F6013A-20E/PT)
- Extended -40C to +125C temperature rating for industrial and harsh environments (vsDSPIC30F6013A-30I/PT)
Ghi chú thiết kế
Estimated: at 5V VDD with the CPU at 20 MIPS active and all peripherals enabled, the DSPIC30F6013AT-20E/PT core current draw is approximately 60 mA to 80 mA typical. Decouple each VDD/VSS pair with a 100 nF ceramic capacitor placed within 5 mm of the pin, and place a single 10 uF bulk tantalum or ceramic capacitor on the board. AVDD and AVSS require their own 100 nF + 10 uF pair, ideally with a ferrite bead between digital and analog supplies to achieve the published 12-bit ADC SNR. Program the LVD (Low-Voltage Detect) trip point via the #pragma config FPOR directive in MPLAB X IDE to ensure brown-out reset triggers below 2.5V.
The 80-pin TQFP package has a theta_JA of approximately 50 C/W on a 4-layer JEDEC test PCB. At 5V VDD with 70 mA active current, power dissipation is approximately 350 mW, yielding a junction temperature rise of approximately 18C above ambient - well within the 125C maximum. In sealed enclosures without airflow or at high ambient temperatures (>70C), add a copper pour under the exposed die pad area (TQFP center pad) and route multiple thermal vias to inner ground planes to reduce junction temperature by 20-30%.
Route the analog inputs AN0-AN15 as far from the digital switching lines (PWM outputs, oscillator traces) as possible to preserve ADC accuracy. Use a ground plane under the analog section and route AVDD/AVSS with wider traces than digital supplies. Place the ADC reference decoupling capacitor (typically 100 nF) directly at the AVDD pin. For high-current motor drive applications, isolate the digital ground return path from the high-current switching return path with a star-ground connection at the MCU VSS pins to avoid ground bounce affecting ADC conversions.
Configuration bits (FOSC, FWDT, FPOR, FGS, etc.) MUST be set via #pragma config in source code; if left at default factory values, the watchdog timer is enabled and may reset the device unexpectedly during debugging. The MCLR pin must be pulled high via a 10 kohm resistor; leaving it floating causes intermittent resets. For ICSP programming, ensure PGEC1/PGED1 (and optionally PGEC2/PGED2) are accessible on the PCB with test points or a 6-pin header - do not route these pins to other functions without considering programming access.
Thông tin tuân thủ
RoHS compliant per Microchip product page; MSL3 per JEDEC J-STD-020; not AEC-Q100 qualified as stand-alone part - for AEC-Q100 designs evaluate dsPIC33EP family. Lead-free and halogen-free per Microchip environmental compliance documentation.