DSPIC30F6013AT-20I/PT - 16-bit DSC, 132KB Flash, 20 MIPS, 80-TQFP
MPN: DSPIC30F6013AT-20I/PT ✓ Hoạt độngDSPIC30F6013AT-20I/PT Tóm tắt
A Digital Signal Controller (DSC) is a class of programmable logic device that combines the deterministic interrupt and peripheral architecture of a microcontroller (MCU) with the computational throughput of a digital signal processor (DSP). In the broader taxonomy, DSCs sit between general-purpose microcontrollers (PIC16, PIC32) and standalone DSPs, belonging to the embedded computing / microcontroller family of semiconductors. The dsPIC30F series was Microchip's first DSC family, designed specifically for 5 V operation in noisy industrial environments.
Key features include a 16-bit modified Harvard architecture with native DSP support (single-cycle 16x16 multiply), on-chip 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), 68 digital I/O pins, and a wide operating voltage range of 2.5 V to 5.5 V. The integrated DSP engine executes a 40-bit accumulator and supports fractional arithmetic, enabling real-time control loops and audio/sensor signal processing.
Architecturally, the DSPIC30F6013A uses a 16-bit data path with a 24-bit instruction word and dual-bus Harvard topology for deterministic cycle counts. The -20I suffix indicates 20 MIPS maximum throughput at the industrial -40C to +85C operating range. The 'A' revision improves ADC performance and adds DMA support compared to the original dsPIC30F6013 silicon. The 'T' suffix designates tape-and-reel packaging.
Typical applications include industrial motor control (BLDC, PMSM, ACIM drives), digital power conversion (SMPS, PFC), sensorless motor commutation, audio processing, automotive body electronics, and embedded control in noisy industrial environments where 5 V tolerance is required.
When designing with this device, ensure adequate decoupling on AVDD/AVSS pairs to achieve specified ADC SNR; the DSP engine is C-programmable via MPLAB XC-DSC compilers, easing porting from pure-DSP or pure-MCU codebases.
This page synthesizes distributor pricing, same-brand drop-in alternatives within the dsPIC30F6013A family, and practical design notes that supplement the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho DSPIC30F6013AT-20I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DSPIC30F6013AT-20I/PT (cùng hình factor và footprint) — khác nhau ở ADC, Package, Timers, MSL Level, Core Architecture.
DSPIC30F6013A-20I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013AT-30I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC30F6013A-30I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6014A-30I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013AT-20E/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6012A-20I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC30F6013AT-20I/PT Tỷ lệ tối đa & tính chất điện
| Product Type | Digital Signal Controller (DSC) |
| Core Architecture | dsPIC30F, 16-bit modified Harvard with DSP engine |
| Maximum CPU Speed | 20 MIPS |
| Program Memory (Flash) | 132 KB (44K x 24) |
| RAM Size | 6 KB |
| Operating Voltage Range | 2.5 V to 5.5 V (3.0 V to 5.5 V for full-speed operation) |
| Khoảng nhiệt độ hoạt động | -40C to +85C (Industrial, -I suffix) |
| Number of I/O Pins | 68 |
| ADC | 12-bit, up to 16 channels |
| Communication Peripherals | UART, SPI, I2C, CAN |
| DSP Engine | 16x16 single-cycle MAC, 40-bit accumulator |
| Hộp | 80-pin TQFP (12x12 mm, -PT suffix) |
| Kiểu lắp đặt | Surface Mount |
| Packaging Type | Tape & Reel (T suffix) |
| Cấp MSL | 3 (per JEDEC J-STD-020) |
| Trạng thái RoHS | Compliant |
Cấu hình chân DSPIC30F6013AT-20I/PT
| Chân 1 | RG15 — PORTG I/O pin 15 |
| Chân 2 | RG14 — PORTG I/O pin 14 |
| Chân 3 | RG13 — PORTG I/O pin 13 |
| Chân 4 | RG12 — PORTG I/O pin 12 |
| Chân 5 | RG11 — PORTG I/O pin 11 |
| Chân 6 | VSS — Ground reference |
| Chân 7 | RG10 — PORTG I/O pin 10 |
| Chân 8 | RG9 — PORTG I/O pin 9 |
| Chân 9 | RG8 — PORTG I/O pin 8 |
| Chân 10 | RG7 — PORTG I/O pin 7 |
| Chân 11 | RG6 — PORTG I/O pin 6 |
| Chân 12 | RG5 — PORTG I/O pin 5 |
| Chân 13 | RG4 — PORTG I/O pin 4 |
| Chân 14 | RG3 — PORTG I/O pin 3 |
| Chân 15 | RG2 — PORTG I/O pin 2 |
| Chân 16 | RG1 — PORTG I/O pin 1 |
| Chân 17 | RG0 — PORTG I/O pin 0 |
| Chân 18 | RF15 — PORTF I/O pin 15 |
| Chân 19 | RF14 — PORTF I/O pin 14 |
| Chân 20 | RF13 — PORTF I/O pin 13 |
| Chân 21 | VSS — Ground reference |
| Chân 22 | VDD — Positive supply (2.5-5.5 V) |
| Chân 23 | RF12 — PORTF I/O pin 12 |
| Chân 24 | RF11 — PORTF I/O pin 11 |
| Chân 25 | RF10 — PORTF I/O pin 10 |
| Chân 26 | RF9 — PORTF I/O pin 9 |
| Chân 27 | RF8 — PORTF I/O pin 8 |
| Chân 28 | RF7 — PORTF I/O pin 7 |
| Chân 29 | RF6 — PORTF I/O pin 6 |
| Chân 30 | RF5 — PORTF I/O pin 5 |
| Chân 31 | RF4 — PORTF I/O pin 4 |
| Chân 32 | AVSS — Analog ground |
| Chân 33 | AVDD — Analog positive supply |
| Chân 34 | RF3 — PORTF I/O pin 3 |
| Chân 35 | RF2 — PORTF I/O pin 2 |
| Chân 36 | RF1 — PORTF I/O pin 1 |
| Chân 37 | RF0 — PORTF I/O pin 0 |
| Chân 38 | AVSS — Analog ground |
| Chân 39 | AVDD — Analog positive supply |
| Chân 40 | RD15 — PORTD I/O pin 15 |
| Chân 41 | RD14 — PORTD I/O pin 14 |
| Chân 42 | RD13 — PORTD I/O pin 13 |
| Chân 43 | RD12 — PORTD I/O pin 12 |
| Chân 44 | RD11 — PORTD I/O pin 11 |
| Chân 45 | RD10 — PORTD I/O pin 10 |
| Chân 46 | RD9 — PORTD I/O pin 9 |
| Chân 47 | RD8 — PORTD I/O pin 8 |
| Chân 48 | VSS — Ground reference |
| Chân 49 | VDD — Positive supply (2.5-5.5 V) |
| Chân 50 | RD7 — PORTD I/O pin 7 |
| Chân 51 | RD6 — PORTD I/O pin 6 |
| Chân 52 | RD5 — PORTD I/O pin 5 |
| Chân 53 | RD4 — PORTD I/O pin 4 |
| Chân 54 | RD3 — PORTD I/O pin 3 |
| Chân 55 | RD2 — PORTD I/O pin 2 |
| Chân 56 | RD1 — PORTD I/O pin 1 |
| Chân 57 | RD0 — PORTD I/O pin 0 |
| Chân 58 | RC15 — PORTC I/O pin 15 |
| Chân 59 | RC14 — PORTC I/O pin 14 |
| Chân 60 | RC13 — PORTC I/O pin 13 |
| Chân 61 | VSS — Ground reference |
| Chân 62 | OSC2 — Crystal oscillator output |
| Chân 63 | OSC1 — Crystal oscillator input |
| Chân 64 | RC12 — PORTC I/O pin 12 |
| Chân 65 | RC11 — PORTC I/O pin 11 |
| Chân 66 | RC10 — PORTC I/O pin 10 |
| Chân 67 | RC9 — PORTC I/O pin 9 |
| Chân 68 | RC8 — PORTC I/O pin 8 |
| Chân 69 | RC7 — PORTC I/O pin 7 |
| Chân 70 | RC5 — PORTC I/O pin 5 |
| Chân 71 | RC4 — PORTC I/O pin 4 |
| Chân 72 | RC3 — PORTC I/O pin 3 |
| Chân 73 | RC2 — PORTC I/O pin 2 |
| Chân 74 | RC1 — PORTC I/O pin 1 |
| Chân 75 | VDD — Positive supply (2.5-5.5 V) |
| Chân 76 | RC0 — PORTC I/O pin 0 |
| Chân 77 | PGD — In-circuit debug data line |
| Chân 78 | PGC — In-circuit debug clock line |
| Chân 79 | MCLR — Master clear reset (active-low) |
| Chân 80 | RA15 — PORTA I/O pin 15 |
Ứng dụng tiêu biểu
DSPIC30F6013AT-20I/PT phù hợp cho 6 Áp dụngs: BLDC/PMSM Motor Control, Digital Switch-Mode Power Supply (SMPS), Industrial Sensor Conditioning, Audio Processing and Effects, Automotive Body Electronics, Uninterruptible Power Supply (UPS) Control.
BLDC/PMSM Motor Control
The DSPIC30F6013AT-20I/PT is well-suited for brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) field-oriented control (FOC) drives. Its 20 MIPS throughput and integrated DSP engine (single-cycle 16x16 MAC, 40-bit accumulator) execute Park/Clarke transforms and PI control loops well within 50 us cycle times, while the dedicated 12-bit ADC with up to 16 channels samples phase currents and the 5 V tolerance handles industrial back-EMF noise on the DC bus.
Được đề xuất
Digital Switch-Mode Power Supply (SMPS)
For digital power conversion such as PFC stages, full-bridge converters, and isolated DC-DC supplies, the DSPIC30F6013AT-20I/PT delivers the DSP throughput required for average-current-mode control at 100 kHz switching frequencies. The 16-bit DSP engine executes compensation loops in single cycles, while the 6 KB RAM holds state variables and the 132 KB Flash stores multi-loop firmware. Its 5 V tolerance simplifies interfacing to analog PFC controllers and gate drivers without level shifters.
Được đề xuất
Industrial Sensor Conditioning
In industrial 4-20 mA loop transmitters, weigh scales, and strain-gauge signal conditioning, the DSPIC30F6013AT-20I/PT performs digital filtering (IIR/FIR), linearization, and temperature compensation on ADC samples. The 12-bit ADC with multiple channels handles load cell, RTD, and thermocouple inputs simultaneously, while the 5 V operating range matches legacy 5 V industrial sensor architectures. The integrated DSP engine runs Kalman filters for sensor fusion without burdening the MCU core.
Được đề xuất
Audio Processing and Effects
The DSPIC30F6013AT-20I/PT can implement real-time audio effects (reverb, EQ, dynamics) and codec post-processing for prosumer audio equipment. With 20 MIPS of DSP throughput, it runs biquad filter cascades and FFT-based spectral processing at 48 kHz sample rates. The 6 KB RAM buffers audio frames, and the I2S/SP peripherals interface to common audio DACs. The 5 V analog supply tolerance simplifies integration with bipolar audio signal chains.
Được đề xuất
Automotive Body Electronics
For non-safety automotive body modules such as seat controllers, HVAC actuators, and lighting drivers, the DSPIC30F6013AT-20I/PT's 5 V tolerance withstands load-dump transients on the 12 V vehicle bus. The CAN peripheral interfaces to vehicle networks, and the DSP engine drives LED matrix dimming curves and motor positioning algorithms. Note: for AEC-Q100 qualified automotive applications, choose the dsPIC33F or dsPIC33E family instead.
Được đề xuất
Uninterruptible Power Supply (UPS) Control
In line-interactive and double-conversion UPS systems, the DSPIC30F6013AT-20I/PT orchestrates inverter control, battery management, and grid synchronization. Its DSP throughput runs PLL algorithms for grid-tie frequency locking, while 12-bit ADCs sense battery voltage/current and output waveforms. The 5 V tolerance simplifies interfacing to 12 V/24 V battery stacks via resistive dividers, and the 132 KB Flash stores multi-mode state machines for charging, inverting, and bypass operation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DSPIC30F6013AT-20I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DSPIC30F6013A-20I/PT | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6014A-30I/PT | DSPIC30F6013AT-20E/PT | DSPIC30F6012A-20I/PT |
|---|---|---|---|---|---|---|---|
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| CPU Speed (MIPS) | 20 MIPS | 20 MIPS | 30 MIPS (+50%) | 30 MIPS (+50%) | 30 MIPS (+50%) | 20 MIPS | 20 MIPS |
| Flash Program Memory | 132 KB (44K x 24) | 132 KB (same) | 132 KB (same) | 132 KB (same) | 144 KB (+9%) | 132 KB (same) | 48 KB (-64%) |
| RAM Size | 6 KB | 6 KB (same) | 6 KB (same) | 6 KB (same) | 8 KB (+33%) | 6 KB (same) | 4 KB (-33%) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +125C (Extended, wider) | -40C to +85C (same) |
| Packaging Form | Tape & Reel | Tray | Tape & Reel | Tray | Tray | Tape & Reel | Tray |
| Number of I/O Pins | 68 | 68 (same) | 68 (same) | 68 (same) | 68 (same) | 68 (same) | 68 (same) |
Bảo phân biệt quan trọng
- 5 V tolerance with integrated DSP engine (vsDSPIC30F6012A-20I/PT)
- Industrial temperature range -40C to +85C (vsDSPIC30F6013AT-20E/PT)
- 20 MIPS baseline with upward scaling options (vsDSPIC30F6013A-30I/PT)
Ghi chú thiết kế
Estimated: at full-speed 20 MIPS operation with all peripherals enabled at 5 V VDD, the DSPIC30F6013AT-20I/PT draws approximately 70 mA (3.5 mA/MIPS typical from datasheet). Place a 10 uF bulk capacitor plus a 0.1 uF ceramic decoupling capacitor on each VDD/AVDD pin pair, located within 5 mm of the IC. Ferrite beads between digital VDD and analog AVDD isolate ADC reference noise.
The 80-pin TQFP (PT) package has a theta_JA of approximately 45 C/W typical. Estimated: at 70 mA and 5 V operation, power dissipation is 0.35 W yielding a junction temperature rise of 16 C above ambient - well within the 85 C industrial limit. For enclosed industrial enclosures with elevated ambient, add thermal copper pours under the exposed pad area to keep Tj below 100 C.
Route the crystal oscillator traces (OSC1, OSCC2) symmetrically and within 10 mm of the IC, with grounded guard traces to prevent noise coupling. The analog AVDD/AVSS pairs should have separate analog ground planes connected at a single point to the digital ground near the IC. The ICSP programming pins (PGD/PGC) should be brought out to a 2.54 mm pinheader for in-field firmware updates.
Do not exceed 5.5 V on any VDD or AVDD pin - the DSPIC30F family is not 3.3 V tolerant on I/O when operated at 5 V. The MCLR pin requires a 10 kohm pull-up to VDD for normal operation; leaving it floating prevents startup. When using the ADC, configure the AVDD pin to settle for at least 100 us after power-up before initiating conversions, otherwise readings will be inaccurate.
Thông tin tuân thủ
RoHS compliant per Microchip product page. Standard industrial -I suffix is NOT AEC-Q100 qualified - for automotive applications, choose dsPIC33F or dsPIC33E families with explicit AEC-Q100 qualification. Halogen-free status not explicitly stated in available data - verify with manufacturer before specifying for halogen-sensitive end products.
