EPM570GT100C3 - MAX II CPLD, 570 LEs, 100-TQFP | Altera (Intel)
MPN: EPM570GT100C3 ✓ Hoạt độngEPM570GT100C3 Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the instant-on, deterministic behavior of traditional PAL/GAL architectures with modern flash-backed configuration memory. In the broader programmable logic hierarchy, CPLDs sit below FPGAs in density but above simple PLDs in capability, offering deterministic timing, high I/O count, and zero-configuration boot time. The MAX II family specifically targets low-power, low-cost glue logic, bus bridging, and I/O expansion roles that FPGAs over-serve.
Key features of the EPM570GT100C3 include 570 logic elements (440 equivalent macrocells), 76 maximum user I/O pins, four global clocks, an 8 Kbit UFM block, JTAG/IEEE 1149.1 boundary-scan support, and MultiVolt core allowing mixed-voltage interfacing on a single die. Its flash-backed non-volatile configuration means zero configuration time on power-up, a critical advantage over SRAM-based FPGAs in deterministic boot applications.
The device uses a Lab/Logic Array Block (LAB) architecture with each LAB containing 16 macrocells and a programmable interconnect array (PIA). The 0.18 µm embedded flash process delivers low dynamic power and high noise immunity, while the 100-pin TQFP package with exposed-pad-compatible footprint simplifies thermal dissipation in space-constrained designs.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-supply sequencing and supervisory glue logic, interface translation between 3.3 V and 1.8 V domains, LED display drivers, and legacy peripheral replacement. The commercial-extended temperature grade also suits benign industrial environments and telecom line cards.
When designing with the EPM570GT100C3, observe the I/O bank VCCIO constraints (each bank must be powered before or simultaneously with the core VCCINT) and provide adequate decoupling (0.1 µF ceramic at every VCC pin) to suppress flash-programming noise. The Quartus II / Quartus Prime toolchain is required for synthesis, fitting, and JTAG programming.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho EPM570GT100C3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPM570GT100C3 (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Package, Process Technology, Programming Interface, Configuration Memory.
EPM570GT100C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM570GT100I5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM570F100C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM570T100A5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM570T100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM570F100A5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM570GT100C3 Tỷ lệ tối đa & tính chất điện
| Family | MAX II |
| Logic Elements | 570 |
| Equivalent Macrocells | 440 |
| Maximum User I/O | 76 |
| User Flash Memory (UFM) | 8 Kbit |
| Internal Operating Frequency | 304 MHz |
| Global Clocks | 4 |
| Process Technology | 0.18 µm 6-layer-metal flash |
| Core Voltage (VCCINT) | 1.71 V to 1.89 V |
| I/O Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V (MultiVolt) |
| Programmability | In-System Programmable (JTAG / IEEE 1149.1) |
| Configuration Memory | Non-volatile flash (instant-on, zero boot time) |
| Nhiệt độ hoạt động | 0 °C to +85 °C (commercial extended) |
| Hộp | 100-pin TQFP (14 x 14 mm) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân EPM570GT100C3
| Chân 1 | I/O — User I/O (Bank 1) |
| Chân 2 | I/O — User I/O (Bank 1) |
| Chân 3 | I/O — User I/O (Bank 1) |
| Chân 4 | I/O — User I/O (Bank 1) |
| Chân 5 | I/O — User I/O (Bank 1) |
| Chân 6 | GND — Ground |
| Chân 7 | I/O — User I/O (Bank 1) |
| Chân 8 | I/O — User I/O (Bank 1) |
| Chân 9 | I/O — User I/O (Bank 1) |
| Chân 10 | I/O — User I/O (Bank 1) |
| Chân 11 | VCCIO1 — Bank 1 I/O supply (1.5/1.8/2.5/3.3 V) |
| Chân 12 | I/O — User I/O (Bank 1) |
| Chân 13 | I/O — User I/O (Bank 1) |
| Chân 14 | I/O — User I/O (Bank 1) |
| Chân 15 | I/O — User I/O (Bank 1) |
| Chân 16 | GND — Ground |
| Chân 17 | I/O — User I/O (Bank 1) |
| Chân 18 | I/O — User I/O (Bank 1) |
| Chân 19 | I/O — User I/O (Bank 1) |
| Chân 20 | I/O — User I/O (Bank 1) |
| Chân 21 | VCCINT — Core supply (1.71-1.89 V) |
| Chân 22 | I/O — User I/O (Bank 1) |
| Chân 23 | I/O — User I/O (Bank 1) |
| Chân 24 | I/O — User I/O (Bank 1) |
| Chân 25 | I/O — User I/O (Bank 1) |
| Chân 26 | GND — Ground |
| Chân 27 | I/O — User I/O (Bank 1) |
| Chân 28 | I/O — User I/O (Bank 1) |
| Chân 29 | I/O — User I/O (Bank 1) |
| Chân 30 | I/O — User I/O (Bank 1) |
| Chân 31 | VCCIO1 — Bank 1 I/O supply |
| Chân 32 | I/O — User I/O (Bank 2) |
| Chân 33 | I/O — User I/O (Bank 2) |
| Chân 34 | I/O — User I/O (Bank 2) |
| Chân 35 | I/O — User I/O (Bank 2) |
| Chân 36 | GND — Ground |
| Chân 37 | I/O — User I/O (Bank 2) |
| Chân 38 | I/O — User I/O (Bank 2) |
| Chân 39 | I/O — User I/O (Bank 2) |
| Chân 40 | I/O — User I/O (Bank 2) |
| Chân 41 | TDI — JTAG Test Data In |
| Chân 42 | TMS — JTAG Test Mode Select |
| Chân 43 | TCK — JTAG Test Clock |
| Chân 44 | nCONFIG — Configuration control (pull high for normal operation) |
| Chân 45 | VCCIO2 — Bank 2 I/O supply |
| Chân 46 | I/O — User I/O (Bank 2) |
| Chân 47 | I/O — User I/O (Bank 2) |
| Chân 48 | I/O — User I/O (Bank 2) |
| Chân 49 | I/O — User I/O (Bank 2) |
| Chân 50 | GND — Ground |
| Chân 51 | I/O — User I/O (Bank 2) |
| Chân 52 | I/O — User I/O (Bank 2) |
| Chân 53 | I/O — User I/O (Bank 2) |
| Chân 54 | I/O — User I/O (Bank 2) |
| Chân 55 | VCCINT — Core supply (1.71-1.89 V) |
| Chân 56 | I/O — User I/O (Bank 2) |
| Chân 57 | I/O — User I/O (Bank 2) |
| Chân 58 | I/O — User I/O (Bank 2) |
| Chân 59 | I/O — User I/O (Bank 2) |
| Chân 60 | GND — Ground |
| Chân 61 | I/O — User I/O (Bank 3) |
| Chân 62 | I/O — User I/O (Bank 3) |
| Chân 63 | I/O — User I/O (Bank 3) |
| Chân 64 | I/O — User I/O (Bank 3) |
| Chân 65 | VCCIO3 — Bank 3 I/O supply |
| Chân 66 | I/O — User I/O (Bank 3) |
| Chân 67 | I/O — User I/O (Bank 3) |
| Chân 68 | I/O — User I/O (Bank 3) |
| Chân 69 | I/O — User I/O (Bank 3) |
| Chân 70 | GND — Ground |
| Chân 71 | I/O — User I/O (Bank 3) |
| Chân 72 | I/O — User I/O (Bank 3) |
| Chân 73 | I/O — User I/O (Bank 3) |
| Chân 74 | I/O — User I/O (Bank 3) |
| Chân 75 | CLK0 — Global clock input 0 / User I/O |
| Chân 76 | VCCIO4 — Bank 4 I/O supply |
| Chân 77 | I/O — User I/O (Bank 4) |
| Chân 78 | I/O — User I/O (Bank 4) |
| Chân 79 | I/O — User I/O (Bank 4) |
| Chân 80 | I/O — User I/O (Bank 4) |
| Chân 81 | GND — Ground |
| Chân 82 | I/O — User I/O (Bank 4) |
| Chân 83 | I/O — User I/O (Bank 4) |
| Chân 84 | I/O — User I/O (Bank 4) |
| Chân 85 | I/O — User I/O (Bank 4) |
| Chân 86 | VCCINT — Core supply (1.71-1.89 V) |
| Chân 87 | I/O — User I/O (Bank 4) |
| Chân 88 | I/O — User I/O (Bank 4) |
| Chân 89 | I/O — User I/O (Bank 4) |
| Chân 90 | I/O — User I/O (Bank 4) |
| Chân 91 | GND — Ground |
| Chân 92 | I/O — User I/O (Bank 4) |
| Chân 93 | I/O — User I/O (Bank 4) |
| Chân 94 | I/O — User I/O (Bank 4) |
| Chân 95 | I/O — User I/O (Bank 4) |
| Chân 96 | CLK1 — Global clock input 1 / User I/O |
| Chân 97 | TDO — JTAG Test Data Out |
| Chân 98 | nCE — Chip enable (active low, tie low for single-device JTAG chain) |
| Chân 99 | nSTATUS — Configuration status (pull-up to VCCIO during normal operation) |
| Chân 100 | CONF_DONE — Configuration done (open-drain, pull-up to VCCIO) |
Ứng dụng tiêu biểu
EPM570GT100C3 phù hợp cho 6 Áp dụngs: Industrial I/O Expansion and Bus Bridging, Power Supply Sequencing and Supervisory Glue Logic, Legacy Peripheral Replacement and Interface Translation, LED Display Driver and Signage Multiplexing, Telecom Line Card Glue Logic, Consumer Appliance Control Board.
Industrial I/O Expansion and Bus Bridging
The EPM570GT100C3 is well suited to industrial I/O expansion where a microcontroller lacks sufficient pins or voltage domains. Its 76 user I/O across four MultiVolt banks allow direct interfacing between a 3.3 V MCU and 1.8 V peripherals without external level shifters. The 570-LE fabric comfortably fits I2C/SPI-to-parallel bridges, address decoding, and timing-critical glue logic, while the 304 MHz internal frequency keeps glue-logic propagation delays under ~5 ns. The instant-on flash configuration eliminates FPGA boot latency, making it ideal for fail-safe industrial controllers that must respond within milliseconds of power-up.
Được đề xuất
Power Supply Sequencing and Supervisory Glue Logic
Power-supply sequencers in multi-rail systems demand deterministic, instant-on logic. The EPM570GT100C3's flash-backed non-volatile configuration boots in microseconds with no external configuration PROM, generating enable signals to DC-DC converters in the correct order. Its four global clocks and 0.18 µm flash process provide sub-5 ns tPD for tight power-good timing budgets. The 8 Kbit UFM can store fault logs or trimming values, replacing an external EEPROM. Designers commonly pair it with PWM controllers such as the UCC28C42 or voltage supervisors to build a complete digital power manager.
Được đề xuất
Legacy Peripheral Replacement and Interface Translation
Many designs require replacing obsolete 74-series glue logic with a single modern device. The EPM570GT100C3 replaces dozens of 74HC/74LVC gates, latches, and bus transceivers while adding 1.5 V-3.3 V voltage translation through its MultiVolt I/O banks. A 570-LE CPLD typically replaces 30-60 discrete SSI/MSI packages, simplifying PCB layout and BOM. The JTAG boundary-scan capability further aids in-circuit testing of legacy boards where bed-of-nails fixtures are impractical. This application is especially relevant for industrial upgrade programs and aerospace sustainment where the original 74xx parts are no longer available.
Được đề xuất
LED Display Driver and Signage Multiplexing
Large LED matrix displays and channel-letter signage benefit from the EPM570GT100C3's high I/O count and deterministic timing. With 76 user I/O, the CPLD can directly drive 8-bit RGB multiplexers for modest-density matrices or function as a refresh controller for larger panels. The 304 MHz internal frequency supports row-scanning frequencies well above the 100 Hz flicker threshold for high-PWM-bit-depth video walls. MultiVolt I/O allows direct connection to LED driver shift registers operating at 3.3 V or 5 V. The non-volatile configuration means the display controller starts scanning immediately on power-up with no boot splash screen.
Được đề xuất
Telecom Line Card Glue Logic
Telecom line cards require deterministic, high-reliability glue logic for TDM bus multiplexing, alarm aggregation, and clock distribution. The EPM570GT100C3's flash-backed configuration ensures no boot-time vulnerabilities for line-protection relays, and its 1.71-1.89 V core draws minimal current. The four global clocks can directly feed telecom framers such as the DS26504 or T1/E1 transceivers with sub-3 ns skew. Commercial-extended temperature rating (0 °C to +85 °C) covers most indoor central-office deployments. Compared to a small FPGA, the MAX II offers predictable timing closure without lengthy place-and-route iterations.
Được đề xuất
Consumer Appliance Control Board
Consumer appliances such as washing machines, induction cooktops, and HVAC controllers need a low-cost, deterministic controller for user-interface scanning, relay driving, and sensor multiplexing. The EPM570GT100C3 replaces microcontrollers in hard-real-time scan loops, with sub-microsecond response to safety-critical inputs. Its 0.18 µm flash process delivers low standby current (<1 mA typical), suiting Energy Star standby requirements. MultiVolt I/O supports direct connection to 3.3 V sensors and 5 V relay drivers without level shifters. Instant-on behavior eliminates MCU firmware boot delays for fast user feedback.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPM570GT100C3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPM570GT100C5N | EPM570GT100I5N | EPM570F100C5N | EPM570T100A5N | EPM570T100C5N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same |
| Logic Elements | 570 | 570 | 570 | 570 | 570 | 570 |
| Speed Grade | C3 (304 MHz) | C5 (~250 MHz) | I5 (industrial temp, speed grade C5) | C5 | A5 (slowest) | C5 |
| Operating Temperature | 0 to +85 C (commercial extended) | 0 to +85 C | -40 to +100 C (industrial) | 0 to +85 C | 0 to +85 C | 0 to +85 C |
| User I/O (max) | 76 | 76 | 76 | 76 | 76 | 76 |
| User Flash Memory (UFM) | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes |
| Silicon Revision | G | G | G | F (earlier revision) | T (earliest revision) | T (earliest revision) |
Bảo phân biệt quan trọng
- Fastest C3 speed grade in MAX II 570-LE family (vsEPM570GT100C5N)
- Commercial-extended temperature grade with standard silicon revision G (vsEPM570F100C5N)
- Same die as T100A5N/T100C5N but faster speed grade (vsEPM570T100A5N)
Ghi chú thiết kế
Decouple every VCCINT pin with a 0.1 µF ceramic capacitor placed within 3 mm of the pin, and bulk-decouple with a 10 µF tantalum or ceramic at the CPLD power entry point. Each VCCIO bank requires its own 0.1 µF + 10 µF decoupling pair because MultiVolt banks switch independently and inject switching noise back into the supply. Power VCCIO banks before or simultaneously with VCCINT to avoid I/O latch-up during ramp-up - the datasheet specifies a maximum VCCIO-VCCINT differential of 0.7 V during power-up sequencing.
Route all JTAG signals (TDI, TDO, TMS, TCK) with 50 Ω controlled impedance and keep the JTAG cable stub shorter than 50 mm total. Place the JTAG connector at the board edge for production programming access. Route nCONFIG, nSTATUS, and CONF_DONE with 10 kΩ pull-ups to VCCIO to prevent spurious configuration events during power glitches. Maintain solid ground planes under the TQFP package; the thermal pad is not exposed on the standard TQFP-100, so rely on copper pours on top and inner layers for heat spreading.
Do not assume that a C5 speed-grade part is bit-stream-compatible with a C3 design - the Quartus fitter generates speed-grade-specific bitstreams. Re-compile the Quartus project when substituting speed grades. Also, do not leave unused I/O floating - configure them as outputs driving low or as inputs with internal pull-up enabled, otherwise floating inputs draw 50-100 µA per pin from leakage. The 8 Kbit UFM has a 100,000-erase-cycle endurance limit - use it for configuration data or trimming values, not for high-write-rate logging.
Group same-bank I/O together on the board to simplify routing and avoid unnecessary VCCIO plane splits. CLK0-CLK3 should each have a short, direct connection to the clock source; avoid routing clock traces over ground splits. For high-speed outputs (>100 MHz), use series termination resistors (22-33 Ω) close to the CPLD pin to dampen reflections. Keep JTAG chain length under 6 inches for reliable ByteBlaster/USB-Blaster programming at 10 MHz TCK.
Thông tin tuân thủ
RoHS compliant per Altera/Intel product page. Lead-free Pb-free assembly. Not AEC-Q100 qualified - industrial-grade part. Commercial extended temperature grade (0 to +85 C).
