EPM570GT100C3 - MAX II CPLD, 570 LEs, 100-TQFP | Altera (Intel)
Артикул: EPM570GT100C3 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $13.31 | $13,31 |
| 10 | $12.45 | $124,50 |
| 100 | $11.2 | $1.120,00 |
| 500 | $10.1 | $5.050,00 |
| 1.000 | $9.05 | $9.050,00 |
EPM570GT100C3 Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the instant-on, deterministic behavior of traditional PAL/GAL architectures with modern flash-backed configuration memory. In the broader programmable logic hierarchy, CPLDs sit below FPGAs in density but above simple PLDs in capability, offering deterministic timing, high I/O count, and zero-configuration boot time. The MAX II family specifically targets low-power, low-cost glue logic, bus bridging, and I/O expansion roles that FPGAs over-serve.
Key features of the EPM570GT100C3 include 570 logic elements (440 equivalent macrocells), 76 maximum user I/O pins, four global clocks, an 8 Kbit UFM block, JTAG/IEEE 1149.1 boundary-scan support, and MultiVolt core allowing mixed-voltage interfacing on a single die. Its flash-backed non-volatile configuration means zero configuration time on power-up, a critical advantage over SRAM-based FPGAs in deterministic boot applications.
The device uses a Lab/Logic Array Block (LAB) architecture with each LAB containing 16 macrocells and a programmable interconnect array (PIA). The 0.18 µm embedded flash process delivers low dynamic power and high noise immunity, while the 100-pin TQFP package with exposed-pad-compatible footprint simplifies thermal dissipation in space-constrained designs.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-supply sequencing and supervisory glue logic, interface translation between 3.3 V and 1.8 V domains, LED display drivers, and legacy peripheral replacement. The commercial-extended temperature grade also suits benign industrial environments and telecom line cards.
When designing with the EPM570GT100C3, observe the I/O bank VCCIO constraints (each bank must be powered before or simultaneously with the core VCCINT) and provide adequate decoupling (0.1 µF ceramic at every VCC pin) to suppress flash-programming noise. The Quartus II / Quartus Prime toolchain is required for synthesis, fitting, and JTAG programming.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для EPM570GT100C3 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с EPM570GT100C3 (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, Process Technology, Programming Interface, Configuration Memory.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EPM570GT100C5N
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$11.05 / шт.
Открыть даташит →EPM570GT100I5N
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$16.5 / шт.
Открыть даташит →EPM570F100C5N
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.2 / шт.
Открыть даташит →EPM570T100A5N
✅ Прямая замена✓ В наличии
$6.72 / шт.
Открыть даташит →EPM570T100C5N
✅ Прямая замена✓ В наличии
$10.2 / шт.
Открыть даташит →EPM570F100A5N
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$9.85 / шт.
Открыть даташит →EPM570GT100C3 Максимальные параметры и электрические характеристики
| Family | MAX II |
| Logic Elements | 570 |
| Equivalent Macrocells | 440 |
| Maximum User I/O | 76 |
| User Flash Memory (UFM) | 8 Kbit |
| Internal Operating Frequency | 304 MHz |
| Global Clocks | 4 |
| Process Technology | 0.18 µm 6-layer-metal flash |
| Core Voltage (VCCINT) | 1.71 V to 1.89 V |
| I/O Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V (MultiVolt) |
| Programmability | In-System Programmable (JTAG / IEEE 1149.1) |
| Configuration Memory | Non-volatile flash (instant-on, zero boot time) |
| Рабочая температура | 0 °C to +85 °C (commercial extended) |
| Корпус | 100-pin TQFP (14 x 14 mm) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов EPM570GT100C3
| Контакт 1 | I/O — User I/O (Bank 1) |
| Контакт 2 | I/O — User I/O (Bank 1) |
| Контакт 3 | I/O — User I/O (Bank 1) |
| Контакт 4 | I/O — User I/O (Bank 1) |
| Контакт 5 | I/O — User I/O (Bank 1) |
| Контакт 6 | GND — Ground |
| Контакт 7 | I/O — User I/O (Bank 1) |
| Контакт 8 | I/O — User I/O (Bank 1) |
| Контакт 9 | I/O — User I/O (Bank 1) |
| Контакт 10 | I/O — User I/O (Bank 1) |
| Контакт 11 | VCCIO1 — Bank 1 I/O supply (1.5/1.8/2.5/3.3 V) |
| Контакт 12 | I/O — User I/O (Bank 1) |
| Контакт 13 | I/O — User I/O (Bank 1) |
| Контакт 14 | I/O — User I/O (Bank 1) |
| Контакт 15 | I/O — User I/O (Bank 1) |
| Контакт 16 | GND — Ground |
| Контакт 17 | I/O — User I/O (Bank 1) |
| Контакт 18 | I/O — User I/O (Bank 1) |
| Контакт 19 | I/O — User I/O (Bank 1) |
| Контакт 20 | I/O — User I/O (Bank 1) |
| Контакт 21 | VCCINT — Core supply (1.71-1.89 V) |
| Контакт 22 | I/O — User I/O (Bank 1) |
| Контакт 23 | I/O — User I/O (Bank 1) |
| Контакт 24 | I/O — User I/O (Bank 1) |
| Контакт 25 | I/O — User I/O (Bank 1) |
| Контакт 26 | GND — Ground |
| Контакт 27 | I/O — User I/O (Bank 1) |
| Контакт 28 | I/O — User I/O (Bank 1) |
| Контакт 29 | I/O — User I/O (Bank 1) |
| Контакт 30 | I/O — User I/O (Bank 1) |
| Контакт 31 | VCCIO1 — Bank 1 I/O supply |
| Контакт 32 | I/O — User I/O (Bank 2) |
| Контакт 33 | I/O — User I/O (Bank 2) |
| Контакт 34 | I/O — User I/O (Bank 2) |
| Контакт 35 | I/O — User I/O (Bank 2) |
| Контакт 36 | GND — Ground |
| Контакт 37 | I/O — User I/O (Bank 2) |
| Контакт 38 | I/O — User I/O (Bank 2) |
| Контакт 39 | I/O — User I/O (Bank 2) |
| Контакт 40 | I/O — User I/O (Bank 2) |
| Контакт 41 | TDI — JTAG Test Data In |
| Контакт 42 | TMS — JTAG Test Mode Select |
| Контакт 43 | TCK — JTAG Test Clock |
| Контакт 44 | nCONFIG — Configuration control (pull high for normal operation) |
| Контакт 45 | VCCIO2 — Bank 2 I/O supply |
| Контакт 46 | I/O — User I/O (Bank 2) |
| Контакт 47 | I/O — User I/O (Bank 2) |
| Контакт 48 | I/O — User I/O (Bank 2) |
| Контакт 49 | I/O — User I/O (Bank 2) |
| Контакт 50 | GND — Ground |
| Контакт 51 | I/O — User I/O (Bank 2) |
| Контакт 52 | I/O — User I/O (Bank 2) |
| Контакт 53 | I/O — User I/O (Bank 2) |
| Контакт 54 | I/O — User I/O (Bank 2) |
| Контакт 55 | VCCINT — Core supply (1.71-1.89 V) |
| Контакт 56 | I/O — User I/O (Bank 2) |
| Контакт 57 | I/O — User I/O (Bank 2) |
| Контакт 58 | I/O — User I/O (Bank 2) |
| Контакт 59 | I/O — User I/O (Bank 2) |
| Контакт 60 | GND — Ground |
| Контакт 61 | I/O — User I/O (Bank 3) |
| Контакт 62 | I/O — User I/O (Bank 3) |
| Контакт 63 | I/O — User I/O (Bank 3) |
| Контакт 64 | I/O — User I/O (Bank 3) |
| Контакт 65 | VCCIO3 — Bank 3 I/O supply |
| Контакт 66 | I/O — User I/O (Bank 3) |
| Контакт 67 | I/O — User I/O (Bank 3) |
| Контакт 68 | I/O — User I/O (Bank 3) |
| Контакт 69 | I/O — User I/O (Bank 3) |
| Контакт 70 | GND — Ground |
| Контакт 71 | I/O — User I/O (Bank 3) |
| Контакт 72 | I/O — User I/O (Bank 3) |
| Контакт 73 | I/O — User I/O (Bank 3) |
| Контакт 74 | I/O — User I/O (Bank 3) |
| Контакт 75 | CLK0 — Global clock input 0 / User I/O |
| Контакт 76 | VCCIO4 — Bank 4 I/O supply |
| Контакт 77 | I/O — User I/O (Bank 4) |
| Контакт 78 | I/O — User I/O (Bank 4) |
| Контакт 79 | I/O — User I/O (Bank 4) |
| Контакт 80 | I/O — User I/O (Bank 4) |
| Контакт 81 | GND — Ground |
| Контакт 82 | I/O — User I/O (Bank 4) |
| Контакт 83 | I/O — User I/O (Bank 4) |
| Контакт 84 | I/O — User I/O (Bank 4) |
| Контакт 85 | I/O — User I/O (Bank 4) |
| Контакт 86 | VCCINT — Core supply (1.71-1.89 V) |
| Контакт 87 | I/O — User I/O (Bank 4) |
| Контакт 88 | I/O — User I/O (Bank 4) |
| Контакт 89 | I/O — User I/O (Bank 4) |
| Контакт 90 | I/O — User I/O (Bank 4) |
| Контакт 91 | GND — Ground |
| Контакт 92 | I/O — User I/O (Bank 4) |
| Контакт 93 | I/O — User I/O (Bank 4) |
| Контакт 94 | I/O — User I/O (Bank 4) |
| Контакт 95 | I/O — User I/O (Bank 4) |
| Контакт 96 | CLK1 — Global clock input 1 / User I/O |
| Контакт 97 | TDO — JTAG Test Data Out |
| Контакт 98 | nCE — Chip enable (active low, tie low for single-device JTAG chain) |
| Контакт 99 | nSTATUS — Configuration status (pull-up to VCCIO during normal operation) |
| Контакт 100 | CONF_DONE — Configuration done (open-drain, pull-up to VCCIO) |
Типичное применение
EPM570GT100C3 подходит для 6 применениеs: Industrial I/O Expansion and Bus Bridging, Power Supply Sequencing and Supervisory Glue Logic, Legacy Peripheral Replacement and Interface Translation, LED Display Driver and Signage Multiplexing, Telecom Line Card Glue Logic, Consumer Appliance Control Board.
Industrial I/O Expansion and Bus Bridging
The EPM570GT100C3 is well suited to industrial I/O expansion where a microcontroller lacks sufficient pins or voltage domains. Its 76 user I/O across four MultiVolt banks allow direct interfacing between a 3.3 V MCU and 1.8 V peripherals without external level shifters. The 570-LE fabric comfortably fits I2C/SPI-to-parallel bridges, address decoding, and timing-critical glue logic, while the 304 MHz internal frequency keeps glue-logic propagation delays under ~5 ns. The instant-on flash configuration eliminates FPGA boot latency, making it ideal for fail-safe industrial controllers that must respond within milliseconds of power-up.
Рекомендуется
Power Supply Sequencing and Supervisory Glue Logic
Power-supply sequencers in multi-rail systems demand deterministic, instant-on logic. The EPM570GT100C3's flash-backed non-volatile configuration boots in microseconds with no external configuration PROM, generating enable signals to DC-DC converters in the correct order. Its four global clocks and 0.18 µm flash process provide sub-5 ns tPD for tight power-good timing budgets. The 8 Kbit UFM can store fault logs or trimming values, replacing an external EEPROM. Designers commonly pair it with PWM controllers such as the UCC28C42 or voltage supervisors to build a complete digital power manager.
Рекомендуется
Legacy Peripheral Replacement and Interface Translation
Many designs require replacing obsolete 74-series glue logic with a single modern device. The EPM570GT100C3 replaces dozens of 74HC/74LVC gates, latches, and bus transceivers while adding 1.5 V-3.3 V voltage translation through its MultiVolt I/O banks. A 570-LE CPLD typically replaces 30-60 discrete SSI/MSI packages, simplifying PCB layout and BOM. The JTAG boundary-scan capability further aids in-circuit testing of legacy boards where bed-of-nails fixtures are impractical. This application is especially relevant for industrial upgrade programs and aerospace sustainment where the original 74xx parts are no longer available.
Рекомендуется
LED Display Driver and Signage Multiplexing
Large LED matrix displays and channel-letter signage benefit from the EPM570GT100C3's high I/O count and deterministic timing. With 76 user I/O, the CPLD can directly drive 8-bit RGB multiplexers for modest-density matrices or function as a refresh controller for larger panels. The 304 MHz internal frequency supports row-scanning frequencies well above the 100 Hz flicker threshold for high-PWM-bit-depth video walls. MultiVolt I/O allows direct connection to LED driver shift registers operating at 3.3 V or 5 V. The non-volatile configuration means the display controller starts scanning immediately on power-up with no boot splash screen.
Рекомендуется
Telecom Line Card Glue Logic
Telecom line cards require deterministic, high-reliability glue logic for TDM bus multiplexing, alarm aggregation, and clock distribution. The EPM570GT100C3's flash-backed configuration ensures no boot-time vulnerabilities for line-protection relays, and its 1.71-1.89 V core draws minimal current. The four global clocks can directly feed telecom framers such as the DS26504 or T1/E1 transceivers with sub-3 ns skew. Commercial-extended temperature rating (0 °C to +85 °C) covers most indoor central-office deployments. Compared to a small FPGA, the MAX II offers predictable timing closure without lengthy place-and-route iterations.
Рекомендуется
Consumer Appliance Control Board
Consumer appliances such as washing machines, induction cooktops, and HVAC controllers need a low-cost, deterministic controller for user-interface scanning, relay driving, and sensor multiplexing. The EPM570GT100C3 replaces microcontrollers in hard-real-time scan loops, with sub-microsecond response to safety-critical inputs. Its 0.18 µm flash process delivers low standby current (<1 mA typical), suiting Energy Star standby requirements. MultiVolt I/O supports direct connection to 3.3 V sensors and 5 V relay drivers without level shifters. Instant-on behavior eliminates MCU firmware boot delays for fast user feedback.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для EPM570GT100C3 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EPM570GT100C5N | EPM570GT100I5N | EPM570F100C5N | EPM570T100A5N | EPM570T100C5N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same |
| Logic Elements | 570 | 570 | 570 | 570 | 570 | 570 |
| Speed Grade | C3 (304 MHz) | C5 (~250 MHz) | I5 (industrial temp, speed grade C5) | C5 | A5 (slowest) | C5 |
| Operating Temperature | 0 to +85 C (commercial extended) | 0 to +85 C | -40 to +100 C (industrial) | 0 to +85 C | 0 to +85 C | 0 to +85 C |
| User I/O (max) | 76 | 76 | 76 | 76 | 76 | 76 |
| User Flash Memory (UFM) | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes |
| Silicon Revision | G | G | G | F (earlier revision) | T (earliest revision) | T (earliest revision) |
Ключевые отличия
- Fastest C3 speed grade in MAX II 570-LE family (против EPM570GT100C5N)
- Commercial-extended temperature grade with standard silicon revision G (против EPM570F100C5N)
- Same die as T100A5N/T100C5N but faster speed grade (против EPM570T100A5N)
Заметки по проектированию
Decouple every VCCINT pin with a 0.1 µF ceramic capacitor placed within 3 mm of the pin, and bulk-decouple with a 10 µF tantalum or ceramic at the CPLD power entry point. Each VCCIO bank requires its own 0.1 µF + 10 µF decoupling pair because MultiVolt banks switch independently and inject switching noise back into the supply. Power VCCIO banks before or simultaneously with VCCINT to avoid I/O latch-up during ramp-up - the datasheet specifies a maximum VCCIO-VCCINT differential of 0.7 V during power-up sequencing.
Route all JTAG signals (TDI, TDO, TMS, TCK) with 50 Ω controlled impedance and keep the JTAG cable stub shorter than 50 mm total. Place the JTAG connector at the board edge for production programming access. Route nCONFIG, nSTATUS, and CONF_DONE with 10 kΩ pull-ups to VCCIO to prevent spurious configuration events during power glitches. Maintain solid ground planes under the TQFP package; the thermal pad is not exposed on the standard TQFP-100, so rely on copper pours on top and inner layers for heat spreading.
Do not assume that a C5 speed-grade part is bit-stream-compatible with a C3 design - the Quartus fitter generates speed-grade-specific bitstreams. Re-compile the Quartus project when substituting speed grades. Also, do not leave unused I/O floating - configure them as outputs driving low or as inputs with internal pull-up enabled, otherwise floating inputs draw 50-100 µA per pin from leakage. The 8 Kbit UFM has a 100,000-erase-cycle endurance limit - use it for configuration data or trimming values, not for high-write-rate logging.
Group same-bank I/O together on the board to simplify routing and avoid unnecessary VCCIO plane splits. CLK0-CLK3 should each have a short, direct connection to the clock source; avoid routing clock traces over ground splits. For high-speed outputs (>100 MHz), use series termination resistors (22-33 Ω) close to the CPLD pin to dampen reflections. Keep JTAG chain length under 6 inches for reliable ByteBlaster/USB-Blaster programming at 10 MHz TCK.
Информация о соответствии
RoHS compliant per Altera/Intel product page. Lead-free Pb-free assembly. Not AEC-Q100 qualified - industrial-grade part. Commercial extended temperature grade (0 to +85 C).
