KSZ8091MNXCA - 10/100 Ethernet PHY | Microchip Technology
MPN: KSZ8091MNXCA ✓ Hoạt độngKSZ8091MNXCA Tóm tắt
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into signals suitable for copper-cable communication and reconstructs incoming signals into a digital interface for the host controller. Within the network hardware hierarchy, the KSZ8091 is an Ethernet interface IC that sits between a MAC-based controller and a 10/100 Ethernet cable. It reduces external circuitry while providing standardized network connectivity.
The KSZ8091 supports 10 Mb/s and 100 Mb/s operation, Full MII, and RMII. Its single-supply architecture operates from 1.2 V, reducing the number of supply rails required around the PHY. Integrated functions include Wake-on-LAN support and LinkMD cable diagnostics, which help a system identify common copper-cable faults. The device uses a 32-QFN package with an exposed thermal pad for compact surface-mount layouts.
The KSZ8091 is a highly integrated 10Base-T/100Base-TX solution intended to reduce board cost and simplify the physical layer of compact Ethernet equipment. Full MII provides a parallel data-and-control interface, while RMII reduces the number of signals required between the PHY and a compatible Ethernet controller. Both interfaces are offered by the MNXCA configuration, allowing the same PHY family to support different controller architectures.
Typical uses include industrial Ethernet controllers, network appliances, embedded systems, IP cameras, access-control equipment, and factory automation modules. The combination of 10/100-Mb/s support, 1.2 V operation, WoL, and cable diagnostics is useful for equipment that must connect over existing CAT-5 infrastructure without requiring gigabit Ethernet magnetics.
PCB design should preserve the layout and component arrangement specified by the manufacturer because a high-speed Ethernet PHY depends on controlled impedance, short return paths, and careful separation between analog and digital circuitry. Confirm RMII timing, reference-clock requirements, magnetics selection, and thermal-pad assembly details before releasing the PCB.
This page organizes the verified device specifications, interface choices, sourcing information, candidate drop-in alternatives, and practical Ethernet design considerations into one engineering-focused reference. It also identifies where device-specific pin, timing, and layout details must be confirmed in the manufacturer datasheet before implementation.
Bộ thay thế dễ dàng lắp đặt cho KSZ8091MNXCA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với KSZ8091MNXCA (cùng hình factor và footprint) — khác nhau ở Cable Type, Number of Transceivers.
KSZ8081MNXCA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →KSZ8081RNACA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →KSZ8091MLX
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8091RNB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8091MNXCA Thông số kỹ thuật
| Device Type | 10/100 Ethernet physical-layer transceiver |
| Supported Data Rates | 10 Mb/s and 100 Mb/s |
| Ethernet Standards | 10Base-T and 100Base-TX |
| Cable Type | CAT-5 unshielded twisted-pair cable |
| Host Interface | Full MII and RMII |
| Number of Transceivers | 1 transceiver |
| Điện áp cung cấp hoạt động | 1.2 V |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +85 °C |
| Package Type | 32-QFN (5 x 5 x 0.9 mm) |
| Kiểu lắp đặt | SMD/SMT |
| Exposed Pad | Present |
| Wake-on-LAN Support | Supported |
| LinkMD Cable Diagnostics | Supported |
| Trạng thái RoHS | Compliant |
| Supply Configuration | Single supply |
| Ethernet Media | 10Base-T/100Base-TX copper |
| Interface Compatibility | Full MII and RMII |
Hướng dẫn cấu hình chân KSZ8091MNXCA 32-qfn (5 x 5 x 0.9 mm)
Cấu hình chân cho KSZ8091MNXCA (32-qfn (5 x 5 x 0.9 mm) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho KSZ8091MNXCA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
KSZ8091MNXCA phù hợp cho 6 Áp dụngs: Industrial Ethernet Controller, Embedded Network Appliance, IP Camera and Security Equipment, Factory Automation Module, Network Access and Communication Equipment, Test and Measurement Instrument.
Industrial Ethernet Controller
The KSZ8091MNXCA fits industrial controller boards that communicate over CAT-5 UTP at 10 Mb/s or 100 Mb/s. Its 1.2 V single-supply operation simplifies the PHY power domain, while Full MII and RMII allow selection according to the host controller architecture. The -40 °C to +85 °C operating range supports industrial environments. Use the device between the Ethernet controller and network magnetics, following the manufacturer reference layout to control differential-pair impedance and exposed-pad heat dissipation.
Được đề xuất
Embedded Network Appliance
The KSZ8091MNXCA provides a compact 10/100 Ethernet endpoint for embedded Linux, real-time control, and industrial gateway products. Supporting both Full MII and RMII lets the same PHY family serve processors with different host-side bus architectures. At 10 Mb/s and 100 Mb/s, it supports legacy CAT-5 infrastructure without a gigabit PHY. LinkMD diagnostics can help identify cable faults, while Wake-on-LAN supports remote power-management workflows.
Được đề xuất
IP Camera and Security Equipment
The KSZ8091MNXCA suits compact IP cameras and security endpoints that require reliable 10/100-Mb/s Ethernet connectivity alongside a dedicated video processor. Its small 32-QFN 5 x 5 mm package supports space-constrained board layouts, and the 1.2 V operating supply can simplify power sequencing around the Ethernet PHY. LinkMD diagnostics are useful for installation troubleshooting, while Wake-on-LAN can support remote maintenance and restart functions in deployed systems.
Được đề xuất
Factory Automation Module
The KSZ8091MNXCA can connect factory automation modules to 10/100-Mb/s Ethernet backbones where legacy copper infrastructure is already installed. Its -40 °C to +85 °C range addresses wide industrial temperature conditions, and LinkMD cable diagnostics help maintenance personnel distinguish wiring problems from equipment failures. The device operates from a single 1.2 V supply and supports Full MII or RMII connectivity to an embedded controller, reducing external PHY component count.
Được đề xuất
Network Access and Communication Equipment
The KSZ8091MNXCA is appropriate for access terminals, serial-to-Ethernet gateways, and compact communication modules that require a standardized 10Base-T/100Base-TX physical layer. Its Full MII interface can connect to a higher-throughput parallel controller, while RMII reduces host-side wiring in space-constrained implementations. The device supports Wake-on-LAN for remote activation and LinkMD diagnostics for cable fault detection, helping simplify both operation and maintenance.
Được đề xuất
Test and Measurement Instrument
The KSZ8091MNXCA can provide a standard 10/100-Mb/s Ethernet management connection in test, measurement, and diagnostic instruments. Its single 1.2 V supply and 32-QFN footprint support compact controller boards, while Full MII and RMII offer flexibility for different processor interfaces. LinkMD diagnostics assist with installed-cable troubleshooting. The 5 x 5 mm exposed-pad package requires careful thermal-pad assembly and layout according to the manufacturer guidance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho KSZ8091MNXCA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | KSZ8081MNXCA | KSZ8081RNACA | KSZ8091MLX | KSZ8091RNB |
|---|---|---|---|---|---|
| Package | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Data Rate | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
Bảo phân biệt quan trọng
- Supports both parallel Full MII and reduced-pin RMII interfaces (vsKSZ8091MLX)
- RMII configuration includes reference-clock output (vsKSZ8091RNB)
- Single 1.2 V operating supply (vsKSZ8081MNXCA)
- Integrated cable diagnostics and remote activation support (vsKSZ8081RNACA)
Ghi chú thiết kế
Use the manufacturer KSZ8091 reference layout and pin-description table for all 32-QFN connections. Keep the 100BASE-TX differential pairs short, continuous, impedance controlled, and isolated from digital clocks and switching supplies. Route the exposed-pad connection and thermal vias according to the package and assembly recommendations because this 5 x 5 mm device requires deliberate heat spreading.
Design the 1.2 V PHY rail with low-noise local decoupling and verify startup behavior across the full 1.2 V operating condition. The 32-QFN exposed pad must be connected according to the manufacturer layout and assembly instructions. Because Ethernet magnetics and the host controller can generate substantial transient current, isolate noisy supply paths and confirm voltage tolerance at the PHY pins under load.
Treat the RMII or MII interface as a timing-critical synchronous interface. Match trace lengths where required by the host-controller specification, provide a clean reference clock, and avoid routing these signals through noisy power-converter regions. Validate rise time, timing margin, and reference-clock jitter with the intended controller rather than relying on nominal Ethernet data rate alone.
Do not substitute an Ethernet PHY solely because it uses a 32-QFN package. Before replacing the KSZ8091MNXCA, compare every pin function, MII/RMII timing, reference-clock source, register address, interrupt behavior, cable-diagnostic feature, Wake-on-LAN implementation, magnetics recommendation, and exposed-pad connection. Software drivers may also depend on the original PHY's register map.
Thông tin tuân thủ
RoHS compliance is stated in the product listing. No additional compliance claims are made without an explicit product-level statement.