LM2902LVQDRQ1 - 4-Channel 5.5V Automotive Op Amp | TI
MPN: LM2902LVQDRQ1 ✓ Hoạt độngLM2902LVQDRQ1 Tóm tắt
An operational amplifier, commonly called an op amp, is a voltage-controlled differential amplifier with very high open-loop gain. Its high input impedance limits loading on the signal source, while negative feedback determines the closed-loop gain and bandwidth. Within the semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. The LM2902LV-Q1 family is designed as a lower-voltage alternative to the wider-supply LM2902-Q1 family.
The principal features include four amplifiers in one 14-pin SOIC, operation from 2.7 V to 5.5 V, a 1 MHz gain-bandwidth product, and a 3 mV input offset voltage. The quad configuration reduces component count and PCB area when an application needs several independent gain stages. The automotive-oriented -Q1 ordering designation identifies the LM2902LV-Q1 qualification class, while the exact operating limits and qualification details should be confirmed in the manufacturer datasheet.
The architecture supports the conventional noninverting, inverting, summing, comparator-style, and voltage-following arrangements commonly used in analog signal conditioning. Because the amplifiers operate from a low-voltage supply, input and output common-mode and output-swing limits require attention near the supply rails. Stable operation also depends on suitable feedback networks, output loading, input bias-current paths, and the manufacturer-recommended bypassing.
Typical uses include automotive sensor interfaces, low-voltage transducer conditioning, current-loop receivers, control-signal amplification, and general instrumentation with multiple analog channels. The four integrated channels are particularly useful when several sensors or low-level signals must be conditioned close to a controller. For battery-powered or 5 V automotive electronics, the 2.7 V to 5.5 V supply range provides useful design headroom.
For layout, place the supply bypass capacitor close to the positive and ground pins and keep sensitive input traces short and away from switching nodes. Verify common-mode range, output swing, capacitive-load stability, and channel-to-channel layout in the final circuit. Decoupling and stability requirements should follow the pin description and application guidance in the Texas Instruments datasheet.
Bộ thay thế dễ dàng lắp đặt cho LM2902LVQDRQ1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2902LVQDRQ1 (cùng hình factor và footprint) — khác nhau ở Gain-Bandwidth Product, Number of Amplifier Channels, Package, Product Type, Supply Configuration.
LM2902DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2902KDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2902KAVQDRDL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2902LVQDRQ1 Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Amplifier Type | General-purpose operational amplifier |
| Automotive Qualification Class | -Q1 automotive class |
| Hộp | 14-pin SOIC |
| Package Pin Count | 14 pins |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân LM2902LVQDRQ1
| Chân 1 | OUTA — Amplifier A output |
| Chân 2 | INA- — Amplifier A inverting input |
| Chân 3 | INA+ — Amplifier A noninverting input |
| Chân 4 | V- — Negative supply connection |
| Chân 5 | INB+ — Amplifier B noninverting input |
| Chân 6 | INB- — Amplifier B inverting input |
| Chân 7 | OUTB — Amplifier B output |
| Chân 8 | OUTC — Amplifier C output |
| Chân 9 | INC- — Amplifier C inverting input |
| Chân 10 | INC+ — Amplifier C noninverting input |
| Chân 11 | V+ — Positive supply connection |
| Chân 12 | IND+ — Amplifier D noninverting input |
| Chân 13 | IND- — Amplifier D inverting input |
| Chân 14 | OUTD — Amplifier D output |
Ứng dụng tiêu biểu
LM2902LVQDRQ1 phù hợp cho 6 Áp dụngs: Automotive Sensor Signal Conditioning, Low-Voltage Current-Loop Receiver, Battery-Powered Monitoring Module, Control-System Analog Front End, Data-Acquisition Buffering, Interface and Level Conditioning.
Automotive Sensor Signal Conditioning
The LM2902LVQDRQ1 is suitable for conditioning several low-level automotive sensor signals because it integrates four general-purpose amplifiers in one 14-pin SOIC and operates from 2.7 V to 5.5 V. Individual channels can provide gain, inversion, filtering, or buffering while reducing the number of separate amplifier packages. Its 1 MHz gain-bandwidth product is appropriate for moderate-bandwidth sensor interfaces rather than precision measurement requiring substantially higher bandwidth or lower offset. Designers should verify the sensor output range against the input common-mode limits and assess the 3 mV offset against the smallest signal of interest.
Được đề xuất
Low-Voltage Current-Loop Receiver
A 4 mA to 20 mA industrial or vehicle current-loop receiver can use one LM2902LVQDRQ1 channel for signal amplification and another for filtering or an output buffer. The device's 2.7 V to 5.5 V operating range supports low-voltage systems, while the four-channel package leaves two amplifiers available for adjacent instrumentation functions. The 1 MHz bandwidth is substantially above the bandwidth normally required by a current-loop input, making loop stability and input filtering the main practical considerations. Verify common-mode range and output swing against the transmitter and sensor-ground requirements.
Được đề xuất
Battery-Powered Monitoring Module
The LM2902LVQDRQ1 fits battery-powered monitoring modules that operate from a regulated low-voltage rail because its 2.7 V to 5.5 V supply range covers common 3.3 V and 5 V systems. Four channels can amplify temperature, pressure, voltage, or current-sense signals without requiring four separate amplifier packages. This integration lowers board-area requirements, although each channel still needs an appropriate feedback network and input-bias path. Confirm quiescent-current and output-swing requirements for the final power budget and ensure the sensor signals remain inside the amplifier's common-mode range.
Được đề xuất
Control-System Analog Front End
A compact control system can use the four channels of the LM2902LVQDRQ1 for command-signal conditioning, feedback amplification, and active filtering. Its 2.7 V to 5.5 V range supports controller-centric electronics, and the 1 MHz gain-bandwidth product permits closed-loop gains that do not require wide-band precision amplification. The integrated quad arrangement simplifies board partitioning and can reduce analog routing complexity. For safety-critical or high-accuracy systems, engineers should review offset, noise, common-mode behavior, and qualification requirements in the manufacturer documentation rather than relying only on the headline specifications.
Được đề xuất
Data-Acquisition Buffering
The LM2902LVQDRQ1 can buffer multiple inputs in a small data-acquisition subsystem where four channels must share a common low-voltage supply. One channel may drive a sensing element while the others condition or isolate adjacent signals, reducing the need for separate buffer packages. The 1 MHz gain-bandwidth product supports general-purpose acquisition stages, while the 3 mV offset must be considered when amplifying small sensor outputs. Place input and feedback components close to their associated pins and check output loading and capacitive stability before using the device directly ahead of an analog-to-digital converter.
Được đề xuất
Interface and Level Conditioning
The LM2902LVQDRQ1 is useful in low-voltage interface circuits where a sensor, switch, or diagnostic line requires amplification or buffering before reaching a digital controller. Its 2.7 V to 5.5 V supply range aligns with many embedded automotive systems, and four channels allow several interface functions to be consolidated. Designers should provide input paths for bias current, limit transient inputs, and use the feedback network to set the closed-loop response. The final design must also confirm that the controller's input thresholds, signal polarity, and allowable propagation delay remain compatible with the amplifier configuration.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2902LVQDRQ1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 14-pin SOIC |
| Brand | Texas Instruments |
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Product Class | General-purpose automotive operational amplifier |
| Automotive Qualification Class | -Q1 |
| Mounting Type | Surface mount |
Bảo phân biệt quan trọng
- Four integrated low-voltage amplifier channels (vsLM2904LVQDRQ1)
- Low-voltage operating range aligned with 3.3 V and 5 V systems (vsLM2902QDRQ1)
- Compact integration in a standard 14-pin SOIC (vsLM2904LVQDRQ1)
Ghi chú thiết kế
Place the supply bypass capacitor close to pin 11 and the negative-supply reference connection associated with the device, using the shortest practical trace and a nearby ground return. Keep feedback resistors and input components adjacent to the amplifier pins they serve. For a quad device, define each channel's signal flow on the PCB and avoid routing one channel's sensitive input beneath another channel's output or a switching-power supply region.
Do not treat a shared 14-pin SOIC footprint as sufficient proof that another amplifier is interchangeable. The replacement must preserve the four-channel pin assignment, 2.7 V to 5.5 V supply range, approximately 1 MHz bandwidth, approximately 3 mV offset, and required automotive qualification. Also verify input common-mode range and output swing; an amplifier can meet supply-voltage requirements while still being unable to process the sensor signal present at its input.
Keep input traces short, guard them against switching-node crosstalk, and use a stable reference or bias return for sources that cannot source or sink DC current. Choose resistor values so the closed-loop gain does not force the amplifier to exceed its intended bandwidth. If driving a long cable, sampling network, or large capacitive node, evaluate noise gain, phase margin, and the need for an isolation resistor against the manufacturer stability guidance.
Thông tin tuân thủ
The -Q1 ordering designation identifies an automotive product family, but the available product information does not state the exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Use the manufacturer datasheet and material declarations for compliance decisions.