LM324KAPWRG4 - Quad 14-TSSOP Op Amp | Texas Instruments
MPN: LM324KAPWRG4 ✓ Hoạt độngLM324KAPWRG4 Tóm tắt
An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify differences between its input terminals. The LM324 family combines four operational amplifiers with supply drain that remains largely independent of supply voltage. Its common-mode input range includes ground, allowing the device to operate from a positive supply while processing signals whose lower excursion approaches the negative supply rail.
The LM324KAPWRG4 is identified as a standard general-purpose amplifier with four circuits and 2 kV ESD protection. According to the LM324 manufacturer information, it supports wide supply ranges of up to 26 V for single-supply operation and up to plus or minus 13 V for dual supplies. Its common-mode input capability is especially useful for sensor interfaces, transducer amplifiers, audio paths, and control signals referenced to ground.
The four-amplifier configuration reduces the number of packages needed when several independent low-frequency signals must be processed. Each amplifier can operate independently, allowing one LM324KAPWRG4 to implement functions such as two instrumentation-amplifier sections, four voltage followers, or a mixture of summing, buffering, and gain stages. Independent operation requires careful grounding and decoupling so that high-current output stages do not disturb sensitive channels sharing the package.
Typical applications include low-cost sensor conditioning, audio preamplification, active filtering, current-to-voltage conversion, and general industrial control. The TSSOP-14 surface-mount package supports compact PCB layouts, but its small thermal dissipation area makes trace and copper-plan consideration important when driving capacitive loads or operating continuously near the supply limits.
For layout, place the package power-decoupling capacitor close to the supply pins and connect each ground reference to a low-impedance ground plane. Avoid placing sensitive input traces beside output traces carrying fast transients. Check output-swing and common-mode limits at the actual supply voltage and load before committing the design.
This product page combines package, application, and drop-in replacement guidance with practical PCB and signal-integrity considerations. It also distinguishes same-footprint LM324 variants so engineers can review orderable suffixes and functional differences before redesigning an existing 14-TSSOP layout.
Bộ thay thế dễ dàng lắp đặt cho LM324KAPWRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM324KAPWRG4 (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Supply Configuration, Number of Channels, Package Type.
LM324PWRG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324APW
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM324APWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324APWRG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324KAPW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324KAPWRG4 Tỷ lệ tối đa & tính chất điện
| Product Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Hộp | 14-TSSOP |
| Kiểu lắp đặt | Surface mount |
| Supply Configuration | Single or dual supply |
| Maximum Single-Supply Voltage | 26 V |
| Maximum Dual-Supply Magnitude | 13 V per rail |
| Typical Supply-Current Drain | 0.8 mA |
| ESD Protection | 2 kV |
| Common-Mode Input Range | Includes ground |
Hướng dẫn cấu hình chân LM324KAPWRG4 14-tssop
Cấu hình chân cho LM324KAPWRG4 (14-tssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM324KAPWRG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM324KAPWRG4 phù hợp cho 6 Áp dụngs: Low-Cost Sensor Signal Conditioning, Audio Preamplification, Active Filtering and Buffering, Current-to-Voltage Conversion, Industrial Control Signal Interfaces, Portable Battery-Powered Analog Circuits.
Low-Cost Sensor Signal Conditioning
The LM324KAPWRG4 is well suited to low-frequency sensor conditioning because its common-mode input range includes ground and four amplifier channels are integrated in one 14-TSSOP package. It can form non-inverting or inverting stages for resistive sensors whose signals remain within the amplifier's input range. The typical 0.8 mA supply-current drain also helps limit power demand in portable measurement systems. Designers should place the supply bypass capacitor close to the device, return input and output grounds to a low-impedance plane, and verify the input bias-current error against the sensor impedance.
Được đề xuất
Audio Preamplification
The four channels in LM324KAPWRG4 allow a compact audio preamplifier to implement several gain stages without requiring four separate packages. Its common-mode input range that includes ground supports single-supply operation with source-coupled audio signals, while the low-power architecture suits battery-operated sound equipment. The TSSOP-14 footprint simplifies compact analog boards, although signal routing must prevent one amplifier's output transient from coupling into adjacent audio inputs. Verify the output swing, slew rate, and channel-to-channel behavior in the intended gain configuration before production.
Được đề xuất
Active Filtering and Buffering
LM324KAPWRG4 can implement buffered active filters, voltage followers, and general small-signal conditioning networks. Four independent amplifiers make it convenient to cascade multiple low-frequency stages while retaining a single package and common ground reference. The device's typical supply-current drain of 0.8 mA supports efficient analog conditioning where each stage operates continuously. Component tolerances and the amplifier's open-loop gain and frequency response determine filter accuracy, so check those characteristics in the manufacturer datasheet and use short, quiet routing around high-impedance nodes.
Được đề xuất
Current-to-Voltage Conversion
The LM324KAPWRG4 is appropriate for low-level current-to-voltage conversion when the source current can be referenced through a suitable shunt or feedback network. Its input stage can accept signals near ground under single-supply operation, matching many current-feedback sensor systems. The wide single-supply capability reaches 26 V according to the manufacturer family information, allowing the same amplifier family to support higher-voltage industrial interfaces. Keep the high-impedance summing node short, protect input terminals from excessive differential voltage, and verify bias-current-induced offset for the selected feedback resistor.
Được đề xuất
Industrial Control Signal Interfaces
The LM324KAPWRG4 can condition controller-level signals in industrial control modules that use positive single supplies. Its common-mode input range includes ground, which supports logic-compatible signals when the supply and signal amplitudes remain within specification, and its 14-TSSOP package helps limit board area. The 2 kV ESD protection associated with this ordering option adds useful handling margin in controlled industrial environments. Confirm the actual signal levels, output loading, temperature grade, and channel isolation when planning the layout, particularly around motor-control power stages.
Được đề xuất
Portable Battery-Powered Analog Circuits
The LM324KAPWRG4's low-power characteristics make it useful in portable analog blocks where four amplifier channels are required. According to the LM324 documentation, the supply-current drain is typically 0.8 mA and remains independent of supply voltage, helping simplify power budgeting. A single positive supply and a common-mode range extending to ground simplify many sensor interfaces. Engineers should disable unneeded channels where the selected variant supports it, account for input bias current in high-impedance sensors, and confirm the complete battery operating range against the output-swing limits.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM324KAPWRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM324PWRG4 | LM324APW | LM324APWR | LM324APWRG4 | LM324KAPW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP - same package | 14-TSSOP - same package | 14-TSSOP - same package | 14-TSSOP - same package | 14-TSSOP - same package |
| Amplifier Count | 4 | 4 | 4 | 4 | 4 | 4 |
| Product Type | General-purpose operational amplifier | General-purpose operational amplifier | LM324-family operational amplifier | LM324-family operational amplifier | LM324-family operational amplifier | LM324-family operational amplifier |
Bảo phân biệt quan trọng
- Four general-purpose amplifiers in one compact package (vsLM324PWRG4)
- Ground-referenced common-mode input capability (vsLM324APW)
- Wide single-supply operating range (vsLM324APWR)
- Low supply-current drain independent of supply voltage (vsLM324APWRG4)
Ghi chú thiết kế
Place the supply-bypass capacitor directly between the LM324KAPWRG4 supply and ground pins, and provide a short return path through the ground plane. The TSSOP-14 leads are closely spaced, so route input and output nets on different layers where practical. Keep each amplifier's feedback components close to its assigned pins to minimize parasitic feedback and sensitivity to adjacent-channel switching.
Route sensitive noninverting inputs away from output pins and switching nodes. The LM324's common-mode range includes ground, but that does not eliminate the need to check input absolute-maximum limits, output swing, and stability at the selected gain. When driving a capacitive load, place a small isolation resistor close to the output and verify the resulting response on the assembled board.
Do not assume that every LM324 suffix is an automatic substitution. Review the exact ordering code for operating-temperature grade, ESD rating, qualification, and package suffix before replacing LM324KAPWRG4. Also verify the actual supply voltage, input common-mode range, and output load; a valid footprint match alone does not guarantee identical electrical limits.
The 14-TSSOP package has limited heat-dissipation area compared with larger leaded packages. For continuous operation at high output current, high ambient temperature, or a large supply-to-output difference, estimate channel dissipation from the output current and voltage drop, then check junction temperature against the selected grade. Use the exposed ground connection and copper area effectively while maintaining the layout requirements for analog isolation.
Thông tin tuân thủ
The available product listings identify the part as a 14-TSSOP general-purpose amplifier with 2 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation in the manufacturer compliance documentation.