LM2904AVQPWRG4Q1 - Dual 26V 700kHz AEC-Q100 Op Amp | TI
MPN: LM2904AVQPWRG4Q1 ✓ Hoạt độngLM2904AVQPWRG4Q1 Tóm tắt
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The dual configuration provides two independent amplifiers in one package, which saves board area in applications such as sensing, filtering, buffering, and control loops. Within the device hierarchy, this part belongs to the operational amplifier family of amplifier ICs, combining wide supply-voltage tolerance with low supply-current consumption.
Key characteristics include a 700 kHz gain-bandwidth product, an input common-mode range that includes ground, and a low typical supply-current drain of 0.7 mA. The common-mode capability supports direct sensing near ground in battery-powered and sensor-interface circuits. Single-supply operation is possible because the common-mode input range reaches the negative supply rail, while the 26 V rating supports higher-voltage industrial control systems.
The LM2904 architecture uses frequency compensation to provide stable closed-loop operation in typical amplifier configurations. Its wide supply range and low supply-current drain suit applications that need adequate signal headroom without continuous high quiescent power. Automotive qualification is provided under AEC-Q100 specifications for the LM2904-Q1 family.
Typical uses include 12 V automotive sensor conditioning, low-side current measurement, transducer amplification, active filtering, and general-purpose analog control. The TSSOP-8 outline also supports compact mixed-signal boards where a dual amplifier is needed rather than two separate single-channel devices.
Design with adequate supply decoupling, confirm the input common-mode and output-swing limits against the actual signal range, and check the maximum total supply voltage before applying power. This page also organizes pinout, packaging, qualification, drop-in alternatives, and application guidance for faster component selection.
Bộ thay thế dễ dàng lắp đặt cho LM2904AVQPWRG4Q1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
LM2904AVQPWRG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904B QPWRQ1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2904AVQPWRG4Q1 Tỷ lệ tối đa & tính chất điện
| Number of Amplifiers | 2 |
| Amplifier Type | Standard general-purpose operational amplifier |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Typical Supply-Current Drain | 0.7 mA |
| Input Common-Mode Range | Includes ground |
| Supply Configuration | Single or dual supply |
| Automotive Qualification | AEC-Q100 qualified |
| Hộp | 8-pin TSSOP (PW) |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân LM2904AVQPWRG4Q1
| Chân 1 | OUTA — Amplifier A output |
| Chân 2 | INA- — Amplifier A inverting input |
| Chân 3 | INA+ — Amplifier A non-inverting input |
| Chân 4 | V- — Negative supply connection |
| Chân 5 | INB+ — Amplifier B non-inverting input |
| Chân 6 | INB- — Amplifier B inverting input |
| Chân 7 | OUTB — Amplifier B output |
| Chân 8 | V+ — Positive supply connection |
Ứng dụng tiêu biểu
LM2904AVQPWRG4Q1 phù hợp cho 6 Áp dụngs: Automotive Sensor Signal Conditioning, Low-Side Current Measurement, Active Low-Pass Filtering, Transducer Amplification, Battery-Powered Monitoring, Industrial Control Analog Front End.
Automotive Sensor Signal Conditioning
The LM2904AVQPWRG4Q1 fits 12 V automotive sensor interfaces because it combines a 26 V supply rating with AEC-Q100 qualification and a 700 kHz gain-bandwidth product. Place one channel in a non-inverting amplifier configuration and use the second channel for filtering or an active transducer driver. The input common-mode range includes ground, which helps when the sensor output rests near 0 V. Decoupling capacitors should be placed close to pins 4 and 8, and input and feedback resistors should be chosen to keep the closed-loop bandwidth well below 700 kHz.
Được đề xuất
Low-Side Current Measurement
A shunt amplifier for a low-side current sensor can use the LM2904AVQPWRG4Q1's two amplifiers to create a differential measurement stage. The first channel senses the shunt voltage and the second provides filtering or an additional gain stage. Its 700 kHz gain-bandwidth product supports measurement bandwidths in the audio-to-low-kilohertz range, while the 0.7 mA typical supply-current drain limits quiescent loading. Maintain common-mode and output-swing headroom, and place the shunt Kelvin connections away from high-current switching nodes to reduce pickup.
Được đề xuất
Active Low-Pass Filtering
The LM2904AVQPWRG4Q1 is suitable for first- or second-order active filters where moderate bandwidth, low supply-current drain, and ground-referenced input capability are important. Each amplifier channel can implement a Sallen-Key or inverting active-filter section with external resistors and capacitors. The 700 kHz gain-bandwidth product leaves headroom above typical audio or sensor-conditioning filter cutoffs. Keep resistor values high enough to limit noise and load effects, but low enough to avoid excessive capacitive loading on the amplifier output.
Được đề xuất
Transducer Amplification
The dual LM2904AVQPWRG4Q1 can condition resistive-bridge, strain-gauge, or resistive temperature-sensor outputs when the excitation and signal levels fit the amplifier's common-mode range. A bridge output can be amplified by one channel while the other channel buffers the reference or drives a guard path. Because the input common-mode range includes ground, unipolar sensor outputs can be measured without a separate bias-supply arrangement. Select feedback resistors for the required gain and verify offset, bias-current, and common-mode accuracy against the temperature range of the final design.
Được đề xuất
Battery-Powered Monitoring
The LM2904AVQPWRG4Q1 works well in battery-powered monitors because its typical supply-current drain is 0.7 mA and its common-mode input range includes ground. One channel can monitor a cell voltage while the other amplifies a sensor or comparator signal. A single-supply configuration simplifies the power tree, although the output-swing limits must be observed at light load. Use low-leakage input biasing and protection components when long battery life is more important than wide input bandwidth.
Được đề xuất
Industrial Control Analog Front End
The LM2904AVQPWRG4Q1 can serve as a general-purpose analog front end in industrial controllers with 12 V or 24 V signal rails. The 26 V supply rating provides headroom for transient-tolerant systems, and the dual configuration handles both sensing and feedback functions. Use amplifier A for the error amplifier and amplifier B for a filter or auxiliary buffer. Keep supply wiring compact, provide local bypass capacitance, and route high-energy switching nodes separately from the high-impedance input nodes to minimize differential noise pickup.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2904AVQPWRG4Q1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2904AVQPWRG4 | LM2904B QPWRQ1 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) |
| Number of Amplifiers | 2 | 2 | 2 |
| Maximum Supply Voltage | 26 V | 26 V | 36 V |
| Gain-Bandwidth Product | 700 kHz | 700 kHz | 1.2 MHz |
| Automotive Qualification | AEC-Q100 qualified | Standard grade | AEC-Q100 qualified |
| Supply Configuration | Single or dual supply | Single or dual supply | Single or dual supply |
Bảo phân biệt quan trọng
- Automotive qualification within the established LM2904 performance class (vsLM2904AVQPWRG4)
- Lower-voltage original LM2904-Q1 rating supports established 26 V designs (vsLM2904B QPWRQ1)
- Dual amplifier in a compact 8-pin TSSOP package (vsLM2904AQTH-13)
Ghi chú thiết kế
Place a supply bypass capacitor close to pins 4 and 8 and route the return directly to the device ground or supply-return plane. The typical supply-current drain is 0.7 mA, but the total current also includes output-current demand and input-bias currents. Keep the maximum total supply voltage below 26 V for this device and include protection for automotive transients where the platform requires it.
Keep the two amplifier channels physically separated when one handles a low-level sensor and the other drives a switching or load stage. Use short traces for feedback connections and avoid routing inputs beneath the TSSOP package or parallel to high-current edges. Place input-referenced protection components close to the pins so surge current is diverted before it reaches the amplifier inputs.
Do not assume that an input at ground can produce an output exactly at ground; the output-swing limits still apply. Likewise, the 700 kHz gain-bandwidth product is not the usable closed-loop bandwidth at high gain. Select feedback resistors and capacitors for the required noise, gain, and stability, then verify operation across temperature and supply tolerance using the manufacturer electrical-characteristics table.
Thông tin tuân thủ
Texas Instruments states that the LM2904-Q1 family is qualified for automotive use in accordance with AEC-Q100 specifications. Other compliance declarations require confirmation on the manufacturer part-details page.