LM2904VQPWR - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM2904VQPWR ✓ Hoạt độngLM2904VQPWR Tóm tắt
An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 family sits within the broader hierarchy of operational amplifiers, analog amplifiers, amplifier ICs, and semiconductors. It can operate from either a single supply or split supplies, making it suitable for circuits powered by industrial rails, batteries, or dual bipolar rails.
The two amplifiers can be used independently for separate signal paths or together in differential, filtering, feedback, and gain-control configurations. The 30 V maximum supply rating provides ample headroom for higher-voltage analog systems, while the 700 kHz bandwidth supports general-purpose signal amplification rather than high-speed precision applications. Its wide -40 °C to 125 °C temperature range allows operation across industrial, automotive-adjacent, and extended-temperature equipment when the system qualification requirements are satisfied.
The LM2904VQPWR uses internal frequency compensation to maintain stable operation in common closed-loop configurations without requiring an external compensation network. Because it contains two amplifier sections, it can reduce component count and board area in designs that require two similar analog channels. Each section has independent input, output, supply, and ground connections, allowing normal dual-amplifier layouts.
Typical uses include sensor-signal conditioning, low-frequency active filters, audio preamplification, motor and actuator feedback loops, and general industrial control interfaces. For battery-powered or split-supply equipment, its dual-amplifier organization can support two related analog channels while sharing one package. Engineers should still verify output swing, input common-mode range, load drive, stability, and noise for the intended feedback network.
PCB implementation requires careful decoupling and grounding. Place the supply bypass capacitor close to the positive and negative supply pins, connect the exposed package ground as applicable, and keep feedback resistors close to the relevant amplifier inputs and outputs. Avoid routing high-current return paths through the analog ground reference. Verify the selected operating point against the manufacturer datasheet, especially when output swing approaches the supply rails.
This product page combines the manufacturer ordering information, verified distributor listings, package details, drop-in alternatives, comparison parameters, and practical PCB guidance. It is intended to accelerate component selection while directing critical electrical verification to the Texas Instruments LM2904V datasheet and product documentation.
Bộ thay thế dễ dàng lắp đặt cho LM2904VQPWR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2904VQPWR (cùng hình factor và footprint) — khác nhau ở Maximum Supply Voltage, Gain-Bandwidth Product, Amplifier Type, Package Type, Operating Temperature Range.
LM2904PWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904VQPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904VQPWR Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| Khoảng nhiệt độ hoạt động | -40 °C to 125 °C |
| Supply Configuration | Single supply or split supply |
| Hộp | 8-pin TSSOP (PW) |
| Package Type | TSSOP |
| Số chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Amplifier Sections | 2 independent, high-gain, frequency-compensated sections |
Hướng dẫn cấu hình chân LM2904VQPWR tssop
Cấu hình chân cho LM2904VQPWR (tssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2904VQPWR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2904VQPWR phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filtering, Audio Preamplification, Motor and Actuator Feedback Control, Battery-Powered Analog Front End, Test and Measurement Front Panel.
Industrial Sensor Signal Conditioning
The LM2904VQPWR fits two-channel industrial sensor conditioning because its two independent amplifier sections can provide gain and buffering without duplicating the IC footprint. With a 30 V maximum supply rating, the device can interface suitable higher-voltage sensor stages while retaining a -40 °C to 125 °C ambient operating range. Place each amplifier around the selected sensor interface, use local feedback networks, and bypass the supply close to pins 4 and 8. The 700 kHz bandwidth is appropriate for many low-to-moderate-bandwidth industrial signals, but engineers must verify the input common-mode range, output swing, sensor impedance, and system noise requirements.
Được đề xuất
Low-Frequency Active Filtering
The LM2904VQPWR is suitable for low-frequency active-filter stages because it provides two independently usable, frequency-compensated amplifiers in one 8-pin TSSOP package. The 700 kHz gain-bandwidth product gives useful bandwidth for audio-band and measurement-filter networks, while the 30 V supply capability supports a wider input range than typical 5 V parts. Configure each section with the required resistor and capacitor network, observe the manufacturer’s stability guidance, and keep high-impedance nodes compact. Verify noise, gain accuracy, and allowable output loading before using the same dual-amplifier configuration for both filter channels.
Được đề xuất
Audio Preamplification
The LM2904VQPWR can serve as a general-purpose audio preamplifier in equipment where two low-frequency channels are required. Its 700 kHz gain-bandwidth product comfortably spans conventional audio bandwidth, and the two independent sections can support stereo or dual-channel amplification. The 30 V maximum supply rating permits operation from higher-voltage analog rails when signal levels and output swing permit. Use stable closed-loop gain, keep input-return paths short, and isolate the audio return from switching currents. Confirm input noise, output drive, distortion, and common-mode limits from the manufacturer electrical characteristics before deploying it in a precision audio path.
Được đề xuất
Motor and Actuator Feedback Control
The LM2904VQPWR is appropriate for general motor or actuator feedback loops that require sensing a control voltage and closing an analog loop. Its dual architecture can monitor a command or feedback signal while amplifying a second related signal, reducing the number of packages on the controller board. The 30 V supply rating supports suitable 24 V industrial systems, and the -40 °C to 125 °C range is useful for extended-temperature equipment. Keep motor-return currents out of the signal ground, provide local supply bypassing, and verify common-mode range, output swing, and stability under the actual load rather than assuming the nominal supply rating alone is sufficient.
Được đề xuất
Battery-Powered Analog Front End
The LM2904VQPWR can implement two amplified channels in battery-powered instrumentation while operating from a single or split supply. Its dual-amplifier configuration reduces package count, and the 700 kHz bandwidth accommodates many sensor, current-sense, and auxiliary audio signals without requiring a high-speed amplifier. The key design checks are quiescent current, input common-mode range, output swing, and behavior as the battery voltage changes. Use the manufacturer’s recommended operating conditions, include supply bypassing, and avoid designs that require rail-to-rail input or output performance unless those functions are confirmed in the device data.
Được đề xuất
Test and Measurement Front Panel
The LM2904VQPWR is well suited to buffering and conditioning inputs in general test and measurement equipment. Two independent amplifiers can support a pair of measurement channels, while the 700 kHz bandwidth is useful for low-speed instrumentation and control signals rather than wideband precision measurement. The 30 V supply capability accommodates protected input stages that operate above conventional logic levels. Designers should evaluate offset, input bias current, noise, and output impedance for the required accuracy, use local decoupling, and avoid long high-impedance traces that can increase pickup and sensitivity to parasitic capacitance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2904VQPWR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2904PWR | LM2904VQPWR |
|---|---|---|---|
| Package | 8-pin TSSOP (PW) | 8-pin TSSOP | 8-pin TSSOP-B |
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Number of Channels | 2 channels | 2 channels | 2 channels |
Bảo phân biệt quan trọng
- Two independent channels in one compact package (vsLM2904PWR)
- 30 V supply capability supports higher-voltage analog rails (vsLM2904PWR)
- 700 kHz bandwidth for general-purpose dual-channel signal conditioning (vsLM2904VQPWR)
Ghi chú thiết kế
Place the supply bypass capacitor immediately adjacent to the LM2904VQPWR supply pins and route it through a short, low-inductance path to the device ground reference. For split-supply operation, decouple both supply rails separately. Keep the two amplifier return paths joined at a quiet analog-ground point and avoid sharing narrow traces with motor, relay, or switching-converter currents. The compact TSSOP-8 footprint makes lead-routing discipline important because longer feedback connections can increase coupling and sensitivity to parasitic capacitance.
Use the minimum practical feedback resistance and keep connected capacitance on amplifier outputs within the manufacturer’s recommended range. High-impedance input nodes should be short and guarded against nearby switching traces. The internal frequency compensation supports normal general-purpose closed-loop configurations, but unusual noise gain, capacitive loading, or very low gain can alter stability or bandwidth. Confirm the final network with the manufacturer application guidance and use an oscilloscope to check ringing when driving long cables, ADC inputs, or capacitive transducers.
Do not interpret the 30 V maximum supply rating as permission to use every input and output voltage at that rail. Check the input common-mode range, output swing, supply limits, and load current at the intended operating point, especially near the positive or negative rail. For single-supply operation, confirm that the signal remains inside the usable input range at minimum supply voltage. Also verify that any 24 V industrial environment uses appropriate surge and reverse-polarity protection outside the amplifier package.
Thông tin tuân thủ
The Texas Instruments LM2904V product documentation should be used to confirm material and environmental declarations for the exact LM2904VQPWR ordering code. No specific compliance claim is established by the manufacturer product-page summary or distributor listing excerpts.