LM393APSR - Dual 38V Open-Collector Comparator | Texas Instruments
MPN: LM393APSR ✓ Hoạt độngLM393APSR Tóm tắt
A differential comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM393APSR belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where open-collector outputs are useful for level translation, wired logic, and systems requiring an external pull-up resistor.
Key specifications include a low input offset voltage of 0.37 mV, a low input bias current of 3.5 nA, and a supply current of 200 µA per comparator. The maximum rating reaches 38 V, while the differential input range extends to ±38 V. An open-collector output can sink logic-level current and connect to TTL, MOS, or CMOS-compatible pull-up networks.
Each of the two channels is electrically independent, allowing simultaneous comparisons or separate threshold-monitoring tasks. The open-collector architecture provides useful flexibility: output rise time is determined by the pull-up resistor and associated capacitance rather than solely by an internal active pull-up. This also permits wired-open-drain logic and level translation between systems with different voltage domains.
Typical uses include industrial control and monitoring, sensor threshold detection, overvoltage and undervoltage supervision, automotive-style battery monitoring, switching-power-supply feedback loops, and general-purpose signal conditioning. The wide supply and differential-input ratings are particularly useful in systems where signal or supply transients may exceed ordinary low-voltage logic levels.
For reliable operation, place the pull-up resistor close to each open-collector output and verify the input common-mode range at the actual supply voltage. Decoupling capacitors should connect directly between the supply and ground pins. PCB signal-trace lengths should remain short to reduce noise pickup on high-impedance comparator inputs.
This page combines the official LM393A family information, package and ordering details, compatible comparison options, and practical implementation guidance. It helps engineers evaluate pin compatibility, output architecture, input characteristics, thermal limits, and replacement options before integrating the comparator into a new PCB.
Bộ thay thế dễ dàng lắp đặt cho LM393APSR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM393APSR (cùng hình factor và footprint) — khác nhau ở Package, Number of Channels, Output Type, Operating Temperature Range.
LM393BPS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2903PSR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LMV393DR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393ADR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393APSRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393APSR Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 independent channels |
| Maximum Supply Voltage | 38 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Điện áp cung cấp | 200 µA per comparator |
| Kiểu đầu ra | Open collector |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| ESD Rating HBM | 2 kV |
| Khoảng nhiệt độ hoạt động | 0°C to +70°C |
| Product Grade | Industrial grade |
| Hộp | 8-pin SOP (PS), tape and reel |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân LM393APSR 8-pin sop (ps), tape and reel
Cấu hình chân cho LM393APSR (8-pin sop (ps), tape and reel gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM393APSR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM393APSR phù hợp cho 6 Áp dụngs: Industrial Threshold Monitoring, Battery Voltage Supervision, Sensor Signal Conditioning, Power Supply Control, Wired Logic and Level Translation, Automotive Electrical Monitoring.
Industrial Threshold Monitoring
The LM393APSR fits industrial threshold monitoring because each of its two channels compares a signal against an independent reference with a specified input offset of 0.37 mV and input bias current of 3.5 nA. Place the reference and sensed voltage on the inverting and non-inverting inputs, then use an open-collector pull-up to drive a digital input. The 38 V maximum supply rating provides margin for industrial rails, while the 0°C to 70°C industrial temperature range supports factory equipment. Designers should verify the common-mode input range at the selected supply voltage and account for output saturation when the pull-up current exceeds the comparator’s sink capability.
Được đề xuất
Battery Voltage Supervision
The LM393APSR can supervise battery or DC-system rails when the monitored voltage fits the applicable common-mode range. One channel may detect an overvoltage condition and the other an undervoltage condition, using external reference dividers and separate open-collector outputs. Its 38 V maximum supply rating is useful for industrial battery packs, while the 0.37 mV input offset supports precise threshold placement. The implementation must prevent the input pins from exceeding their permitted range, account for divider tolerance and hysteresis, and use pull-up rails appropriate for the system receiving the fault signals.
Được đề xuất
Sensor Signal Conditioning
The LM393APSR is useful for converting a slowly changing sensor signal into a logic event by comparing the sensor against a reference. The 3.5 nA input bias current limits loading of high-impedance sensor networks, and the 0.37 mV offset supports accurate decisions near the reference level. Each independent channel can process a different threshold or can implement complementary detection with external feedback. Because the output is open collector, a pull-up resistor can set the interface voltage for TTL, MOS, or CMOS logic. Add deliberate hysteresis to prevent chatter around the switching threshold and route the high-impedance input traces away from switching nodes.
Được đề xuất
Power Supply Control
The LM393APSR can support power-supply control loops by comparing a scaled feedback voltage with a reference and driving a control input through its open-collector output. Its dual-channel arrangement allows independent overvoltage and undervoltage checks or two stages of supervisory control. The comparator’s 38 V supply-class rating supports wide-input industrial designs, while its low 200 µA-per-comparator supply current limits overhead in auxiliary monitoring circuits. Feedback dividers, compensation components, and the pull-up network must be designed around the intended switching topology. The open-collector output can pull an enable or control node low, but it cannot directly drive a high-voltage gate without an appropriate driver stage.
Được đề xuất
Wired Logic and Level Translation
The LM393APSR’s open-collector output supports wired-open-drain logic and level translation because the pull-up rail, rather than the output stage, establishes the high voltage. This allows a sensor or supervisory circuit to interface with logic operating at a different voltage. Two independent channels can implement wired AND behavior or combine fault signals. The design trade-off is that output rise time is set by the pull-up resistance and the capacitance of the connected bus. Use a pull-up strong enough to meet the receiver’s rise-time requirement but weak enough to remain within the comparator’s sink-current limit. Keep the bus short and use Schmitt action or external hysteresis where noisy conditions could cause multiple transitions.
Được đề xuất
Automotive Electrical Monitoring
The LM393APSR can be evaluated for automotive electrical monitoring when the complete operating environment is compatible with its 0°C to 70°C industrial rating. Its two channels support independent checks of a vehicle electrical rail, such as overvoltage and undervoltage conditions, while the 38 V maximum supply rating accommodates higher-voltage systems. The open-collector outputs are convenient for wired fault signals with external pull-ups. Automotive qualification requirements must be checked separately because the exact LM393APSR suffix is not presented as an AEC-Q100-qualified variant. Any candidate device should also be reviewed for load dump, transient immunity, temperature range, and automotive production requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM393APSR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM393BPS | LM2903PSR | LMV393DR | LM393ADR | LM393APSRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOP (PS) | 8-pin SOP (PS) - same | 8-pin SOP (PS) - same | 8-pin SOP (PS) - same | 8-pin SOP (PS) - same | 8-pin SOP (PS) - same |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
Bảo phân biệt quan trọng
- Higher voltage headroom than LM2903 (vsLM2903PSR)
- Low input offset supports precise thresholds (vsLMV393DR)
- Dual independent open-collector channels (vsLM2903PSR)
- Direct SOIC footprint reuse (vsLM393BPS)
Ghi chú thiết kế
Route each open-collector output directly to its pull-up resistor and receiving circuit to minimize loop area and switching noise. Keep the comparator input traces short and away from power-switching nodes, inductors, and high-current return paths. Place the supply bypass capacitor directly between the device supply and ground pins, with a short ground return. Because the inputs can present very high impedance, keep surrounding copper and test-point leakage in mind when setting accurate thresholds.
The pull-up resistor sets the output high level and determines the open-collector sink current. Select it so the maximum low-state current remains below the comparator’s output sink limit, while the resistance and total bus capacitance provide the required rise time. Estimated relationship: output rise time is approximately 2.2 times pull-up resistance times total bus capacitance. Confirm that the pull-up supply voltage is permitted by the output structure and that its current remains within system power limits.
Do not assume that the 38 V maximum supply rating permits every input to remain at 38 V under all operating conditions. Verify the common-mode input range, differential input limit, and supply-current behavior at the actual rail voltage. Also add hysteresis around thresholds where noise or slow input slopes could cause output chatter. For battery systems, the pull-up rail must remain present long enough for downstream circuitry to interpret the open-collector fault signal reliably.
Thông tin tuân thủ
The exact LM393APSR ordering suffix is identified as an industrial-grade 8-pin SOP comparator. No exact RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was established for this suffix.