LT1464CS8 - Dual 1MHz Micropower JFET Op Amp | ADI
MPN: LT1464CS8 ✓ Hoạt độngLT1464CS8 Tóm tắt
An operational amplifier is a voltage-feedback amplifier used to amplify differential signals, buffer sensors, implement active filters, and serve as the gain element in control or instrumentation circuits. The LT1464 belongs to the JFET-input operational amplifier family and the broader voltage-feedback amplifier category. Its low-bias-current input stage is especially useful when the source impedance is high or leakage currents would otherwise disturb the measurement.
Key operating characteristics include a 1 MHz gain-bandwidth product, 0.9 V/µs slew rate, 500 fA typical input bias current, and no more than 200 µA supply current per amplifier. According to the Analog Devices LT1464 product information, the amplifiers are unity-gain stable with capacitive loads up to 10 nF. Their outputs can drive a 10 kΩ load to within 1.5 V of either supply rail, supporting practical single-supply signal-conditioning circuits.
The JFET input architecture combines low input bias current with the amplifier’s micropower operating current. Gain-bandwidth behavior supports approximately 1 MHz closed-loop bandwidth at unity gain, while the specified output-current capability allows the device to follow higher-frequency signals without requiring a high-power output stage. Designers should still evaluate output swing, load current, and supply voltage together because the usable output range narrows near the rails.
Typical applications include low-frequency sensor signal conditioning, current-to-voltage conversion, photodiode and other high-impedance transducers, precision filtering, battery-powered instrumentation, and general dual-amplifier signal chains. The 8-pin SOIC package provides two amplifiers and can simplify PCB layout when both channels are required in adjacent analog sections.
A critical design consideration is stability with capacitive loading. The manufacturer specifies unity-gain stability for loads up to 10 nF, so longer sensor cables or unusual load networks may require isolation resistance close to the input. Grounding and bypassing should follow the manufacturer’s recommended application circuit, with short return paths and local supply decoupling to preserve low-noise behavior.
This product information combines the manufacturer’s electrical characteristics with practical guidance on low-power operation, capacitive loading, output swing, and PCB implementation. It also organizes the verified ordering options and key limitations into a form that supports direct part selection, sourcing, and circuit design.
Bộ thay thế dễ dàng lắp đặt cho LT1464CS8 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
LT1464CS8#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT1464CS8 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | JFET-input operational amplifier |
| Number of Circuits | 2 circuits |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.9 V/µs |
| Maximum Supply Current | 200 µA per amplifier |
| Typical Input Bias Current | 500 fA |
| Capacitive Load Stability | 10 nF at unity gain |
| Output Swing | Within 1.5 V of either supply with a 10 kΩ load |
| Hộp | 8-pin SOIC, 0.154 inch (3.90 mm) width |
| Kiểu lắp đặt | Surface mount |
| Input Bias Current | Picoampere class |
Hướng dẫn cấu hình chân LT1464CS8 8-pin soic, 0.154 inch (3.90 mm) width
Cấu hình chân cho LT1464CS8 (8-pin soic, 0.154 inch (3.90 mm) width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LT1464CS8.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LT1464CS8 phù hợp cho 6 Áp dụngs: High-Impedance Sensor Signal Conditioning, Battery-Powered Instrumentation, Precision Active Filtering, Photodiode and Transducer Amplification, Low-Power ADC Input Buffer, Industrial Control and Monitoring Loops.
High-Impedance Sensor Signal Conditioning
The LT1464CS8 fits high-impedance sensor front ends because its JFET input stage provides 500 fA typical input bias current while each amplifier consumes no more than 200 µA. Place one channel in a non-inverting or differential conditioning stage and use the other for gain, filtering, or level translation. The 1 MHz gain-bandwidth product supports low-frequency signal paths, while low input bias reduces disturbance of high-source-resistance sensors. Before release, check offset voltage, input capacitance, noise, and drift against the sensor error budget.
Battery-Powered Instrumentation
The LT1464CS8 is suitable for portable instruments that must conserve power without abandoning JFET-input signal integrity. Its maximum supply current of 200 µA per amplifier limits the amplifier contribution to system consumption, and the 500 fA typical input bias current is valuable when measuring leakage-sensitive nodes. The dual configuration supports two analog channels in one 8-pin SOIC, helping conserve board area. Use local supply bypassing and a quiet reference or excitation source because the amplifier’s low power consumption does not eliminate errors caused by noisy external circuitry.
Precision Active Filtering
The LT1464CS8 can implement precision low-frequency active filters where low input bias current and micropower operation are both useful. Its 1 MHz gain-bandwidth product gives adequate bandwidth for many sensor, audio-band control, and instrumentation networks, while dual channels allow cascading active stages in one package. Use the appropriate noise-gain topology and stable resistor values to avoid unintended oscillation. Capacitive loading at the output must remain compatible with the manufacturer’s unity-gain stability rating of 10 nF, or be isolated as recommended in the datasheet.
Photodiode and Transducer Amplification
The 500 fA typical input bias current of the LT1464CS8 makes it a logical fit for photodiode, capacitive transducer, and other leakage-sensitive amplification stages. The JFET input minimizes current drawn from the transducer, helping preserve small output signals before further filtering or conversion. Its 0.9 V/µs slew rate and 1 MHz gain-bandwidth product support practical low-to-moderate bandwidth signal chains. The designer must still account for photodiode capacitance, amplifier noise, offset voltage, and cable loading to determine the achievable signal-to-noise ratio.
Low-Power ADC Input Buffer
LT1464CS8 can buffer a sensor or slow analog signal into an ADC input when low power and high input impedance are priorities. The 1 MHz gain-bandwidth product covers many low-bandwidth conversion systems, and the dual amplifier allows one channel for acquisition while the other provides gain or active filtering. Because the output can reach only within 1.5 V of either supply with a 10 kΩ load, set the signal and output ranges carefully. Confirm ADC settling requirements and account for capacitive input loading before using the full bandwidth.
Industrial Control and Monitoring Loops
The LT1464CS8 is applicable to low-frequency industrial monitoring loops where a dual, low-power amplifier can condition two related signals without adding substantial supply demand. Its 1 MHz bandwidth is appropriate for many slow control and sensor loops, and picoampere input bias supports higher-impedance sensing nodes. The 8-pin SOIC package simplifies assembly, but industrial temperature qualification, output swing, electromagnetic interference, and long-cable stability require separate evaluation. Use short traces and a clean ground reference to prevent external coupling from dominating the small-signal measurement.
Dữ liệu tham khảo kỹ thuật cho LT1464CS8 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LT1464CS8#PBF |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC - same package |
| Number of Amplifiers | 2 circuits | 2 circuits |
| Amplifier Input Type | JFET | JFET |
| Gain-Bandwidth Product | 1 MHz | 1 MHz |
| Slew Rate | 0.9 V/µs | 0.9 V/µs |
| Maximum Supply Current | 200 µA per amplifier | 200 µA per amplifier |
| Typical Input Bias Current | 500 fA | 500 fA |
| Unity-Gain Capacitive Load | 10 nF | 10 nF |
Bảo phân biệt quan trọng
- Direct same-family ordering-code replacement (vsLT1464CS8#PBF)
- Very low bias current for precision leakage control (vsLT1464CS8#PBF)
- Micropower operation with two integrated channels (vsLT1464CS8#PBF)
Ghi chú thiết kế
Do not treat the advertised 10 nF capacitive-load rating as unlimited stability. Long sensor leads, ADC sampling inputs, and probe capacitance can create resistive or reactive loading that changes the effective response. Keep the standard noninverting and inverting networks close to the device, compare the connected load against the 10 nF unity-gain specification, and use the manufacturer’s isolation method when greater capacitance is unavoidable.
Route each amplifier’s input and feedback paths away from supply, clock, and switching-node traces. Connect the two channels to their respective signal sources without sharing long high-impedance traces, because shared paths can couple leakage and noise into both channels. Place local supply bypassing close to the SOIC power pins and maintain a continuous ground reference beneath the device to reduce inductive voltage differences across the package.
Estimated: each amplifier’s maximum supply current is 200 µA, so the dual amplifier can account for up to 400 µA of supply current before external bias current is included. Calculate total power as Estimated: P = VIN × ISUPPLY, using the actual supply voltage and measured system current. The LT1464 remains micropower, but battery-life calculations must also include sensor, reference, and interface loads.
Account for output swing before choosing the circuit’s common-mode range. The published specification places the output within 1.5 V of either supply when driving 10 kΩ. Bias a single-supply design near mid-supply and avoid requiring linear operation close to either rail, where the amplifier’s output cannot follow the ideal input. For ADC interfaces, also verify that the selected reference and signal limits remain inside the amplifier’s linear operating region.
Thông tin tuân thủ
The #PBF ordering code identifies a lead-free-marked LT1464CS8 configuration, but the cited excerpts do not explicitly state the compliance status of the standard LT1464CS8 ordering code.