MAX314CUE+ - Quad 10Ω SPST CMOS Switch | Analog Devices
MPN: MAX314CUE+ ✓ Hoạt độngMAX314CUE+ Tóm tắt
A CMOS analog switch is a semiconductor-controlled routing device that connects or isolates circuit nodes under digital control. The MAX314 family belongs to the analog-switch hierarchy, which includes multiplexers, selectors, and SPST switch arrays. Unlike a mechanical relay, an analog switch changes state electronically with no moving parts, making it suitable for compact instrumentation, signal-routing, and test systems.
The MAX314 provides four single-pole, single-throw channels, a maximum on-resistance of 10Ω, and channel-to-channel matching of 1.5Ω. Because the switches conduct equally well in either direction, one package can route positive, negative, or bipolar signals. Leakage is specified at 2.5nA at +85°C, helping preserve signal integrity when a switch is off and high-impedance loads are connected.
The four channels operate independently, allowing simultaneous control of separate signal paths. Matching of 1.5Ω minimizes gain or attenuation differences caused by unequal switch resistance, while the 10Ω maximum on-resistance supports common low-level analog signals. The CMOS implementation also provides low power consumption, although supply current and switching timing should be checked against the operating conditions in the manufacturer datasheet.
Typical uses include signal isolation between instrumentation channels, routing between a sensor and a measurement circuit, and selecting inputs in test and measurement equipment. The device can also serve in industrial control systems where an external controller must connect a source to an analog processing chain without changing the baseband voltage.
For PCB design, keep control traces away from sensitive analog routes and provide a stable ground reference to all package pins. Confirm the absolute maximum voltage, input logic levels, charge injection, off leakage, and switching-time limits before applying the device to high-voltage or high-speed signals.
This page combines the MAX314 family electrical characteristics, pin-compatible alternatives, application guidance, comparison parameters, and practical PCB considerations in a format designed for rapid component selection and design review.
Bộ thay thế dễ dàng lắp đặt cho MAX314CUE+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX314CUE+ (cùng hình factor và footprint) — khác nhau ở Dual-Supply Operating Range, On-Resistance, On-Resistance Matching Between Channels, Switch Configuration.
MAX314EUE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX313CUE+
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX313EUE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX312CUE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX313LEUE+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX314CUE+ Tỷ lệ tối đa & tính chất điện
| Number of Channels | 4 channels |
| Switch Configuration | 1:1 SPST |
| Signal Conductivity | Bidirectional |
| On-Resistance | 10Ω maximum |
| On-Resistance Matching Between Channels | 1.5Ω |
| Supply Voltage Range | 4.5V to 30V |
| Dual-Supply Operating Range | ±4.5V to ±20V |
| Off Leakage Current | 2.5nA at +85°C |
| Technology | CMOS |
| Số lượng chân | 16 pins |
| Hộp | 16-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| ESD Tolerance | Greater than 2000V per method 3015.7 |
| Power Consumption | Low power consumption |
| Trạng thái RoHS | Compliant |
| REACH Status | Compliant |
Hướng dẫn cấu hình chân MAX314CUE+ 16-pin tssop
Cấu hình chân cho MAX314CUE+ (16-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX314CUE+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX314CUE+ phù hợp cho 6 Áp dụngs: Sensor Signal Routing, Test and Measurement Equipment, Industrial Control Signal Isolation, Battery-Powered Instrumentation, Data Acquisition Multiplexing, Analog Signal Fan-Out.
Sensor Signal Routing
The MAX314CUE+ is suitable for routing a sensor output to a measurement amplifier while limiting the number of interconnects in the analog path. Each of its four SPST channels can connect or isolate a signal bidirectionally, and the 10Ω maximum on-resistance is manageable when the selected amplifier input presents a substantially higher impedance. The 2.5nA leakage rating at +85°C also limits loading of high-impedance sensor nodes. Designers should calculate the source impedance, injected offset, and settling behavior before using the switch at the input of precision conversion circuitry.
Được đề xuất
Test and Measurement Equipment
The MAX314CUE+ can route instrument signals between a source, an input terminal, and a test fixture without using moving relays. Four independent SPST channels provide flexibility for signal isolation, while the 1.5Ω channel-to-channel matching helps maintain similar insertion loss among measured paths. The low 2.5nA leakage at +85°C is valuable when the fixture includes high-impedance probes. Because the device is intended for 4.5V-to-30V operation, the fixture must keep every switched node within the absolute maximum voltage range specified by the manufacturer.
Được đề xuất
Industrial Control Signal Isolation
The MAX314CUE+ can isolate individual analog control or monitoring signals in an industrial control assembly. Bidirectional SPST operation allows the same routing arrangement whether the switch is used to connect a controller output to an actuator interface or a sensor signal back to a controller input. Its low power consumption is useful in distributed systems, while the 16-pin TSSOP package supports compact board layouts. Firmware and hardware designers should confirm logic thresholds, switch timing, transient limits, and isolation behavior under the applicable industrial operating conditions.
Được đề xuất
Battery-Powered Instrumentation
The MAX314CUE+ fits compact, low-power instrumentation because it combines four analog channels with low power consumption and an electrical rating of 4.5V to 30V. Operating from a single 5V rail simplifies portable equipment, while its bidirectional switches can support both input selection and output routing. The principal design trade-off is the 10Ω maximum on-resistance, which can create a divider with a low-impedance downstream input. Use a high-impedance receiving stage or buffer when insertion resistance would otherwise degrade signal accuracy.
Được đề xuất
Data Acquisition Multiplexing
The MAX314CUE+ can perform front-end channel selection in a small data-acquisition system using four independently controlled SPST paths. Its 1.5Ω on-resistance matching reduces channel-dependent variation, and low leakage helps prevent unloaded inputs from shifting when the switch is open. The device should be placed close to the multiplexed source to minimize parasitic capacitance and pickup. For high-speed acquisition, evaluate charge injection, switching time, input capacitance, and settling time from the MAX314 datasheet before selecting the sampling interval.
Được đề xuất
Analog Signal Fan-Out
The MAX314CUE+ can distribute a low-level analog signal through separate switched paths when the receiving circuits present sufficiently high impedance. Because the channels are electrically independent, each path can be enabled at a different time without mechanically disturbing the source. On-resistance matching of 1.5Ω supports similar signal attenuation across channels. The design must account for simultaneous switching transients, control-signal settling, and the cumulative effect of leakage into nearby high-impedance nodes, particularly at elevated temperatures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX314CUE+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX314EUE+ | MAX313CUE+ | MAX313EUE+ | MAX312CUE+ | MAX313LEUE+T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | SPST | SPST | SPST | SPST | SPST | SPST |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
Bảo phân biệt quan trọng
- Four independently controlled analog channels in one package (vsMAX313LEUE+T)
- Low maximum on-resistance for the MAX314 family (vsMAX313LEUE+T)
- Improved channel-to-channel resistance matching (vsMAX312CUE+)
- Bidirectional conduction in a compact TSSOP package (vsMAX313CUE+)
Ghi chú thiết kế
Treat the 10Ω maximum on-resistance as part of the signal path, not as an isolated component rating. When the switch drives a lower-impedance load, calculate the voltage-divider ratio formed by the switch resistance and the load. Use a receiving stage with substantially higher input impedance when insertion resistance would affect gain. The 1.5Ω channel matching helps limit path-to-path variation, but amplifier offset, capacitor charging, and leakage must also be included in the error budget.
Place the MAX314CUE+ close to the connector, sensor, or amplifier input that it routes. Keep switched-node traces short to reduce parasitic capacitance and susceptibility to induced noise, while separating the digital control traces from high-impedance analog nets. Provide a low-impedance ground plane and connect the package ground reference according to the manufacturer pin description. Review exposed or adjacent supply pins for adequate decoupling where the selected board architecture requires it.
Do not infer that every MAX312, MAX313, or MAX314 suffix is interchangeable. Verify the control polarity, input logic thresholds, supply range, temperature grade, absolute maximum voltages, on-resistance, leakage, and timing for the exact alternate part. Bidirectional operation does not permit signals outside the device ratings, and the 2.5nA leakage figure applies at the stated temperature and measurement conditions. Check the product-selection table before approving a substitution.
Thông tin tuân thủ
RoHS and REACH compliance are identified for MAX314CUE+ through component comparison information. AEC-Q100 qualification, lead-free status, halogen-free status, and conflict-minerals status are not established for this part.