MAX3232EIPWE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232EIPWE4 ✓ Hoạt độngMAX3232EIPWE4 Tóm tắt
An RS-232 transceiver is an interface integrated circuit that converts between single-ended logic-level signals and differential, bipolar RS-232 signals. It belongs to the line-driver and receiver family, then to the broader transceiver and interface IC hierarchy. The MAX3232EIPWE4 implements the physical-layer signaling required by TIA/EIA-232-F and ITU V.28 systems while presenting ordinary CMOS logic levels to the host controller.
Key features include a 2/2 driver-receiver configuration, 3 V to 5.5 V operation, 250 kbps data rate, and ±15 kV IEC ESD protection. The -40 °C to 85 °C industrial temperature range supports both commercial and industrial equipment. Tape-and-reel packaging is identified for the E suffix, while the 16-TSSOP body measures 0.173 inches, or 4.40 mm, in width.
The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 transmitters. This allows the device to communicate over cable distances where the receiver must tolerate bipolar signal swings relative to ground. The integrated protection circuits help improve system robustness when users connect external cables or connectors to the board.
Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, printer interfaces, and embedded systems that exchange data with legacy RS-232 peripherals. The 250 kbps maximum rate is suitable for command-and-control links rather than high-throughput storage transfers. The 3 V supply option also helps reduce the logic power requirement in mixed-voltage embedded designs.
When laying out this device, place the charge-pump capacitors close to their designated pins, route transceiver outputs toward the connector, and keep sensitive logic-side traces away from cable-side nets. Confirm line-driver load capability, receiver thresholds, and system grounding in the manufacturer datasheet before releasing a high-volume design.
Bộ thay thế dễ dàng lắp đặt cho MAX3232EIPWE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX3232IPWG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ECPWG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232ECPWE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN65C3232EPWG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232EIPWE4 Thông số kỹ thuật
| Product Type | RS-232 line driver/receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Tốc độ dữ liệu | 250 kbps |
| Supply Voltage Range | 3 V to 5.5 V |
| ESD Protection | ±15 kV IEC ESD |
| Khoảng nhiệt độ hoạt động | -40 °C to 85 °C |
| Hộp | 16-TSSOP, 0.173 inch (4.40 mm) width |
| Kiểu lắp đặt | Surface mount |
| Packaging | Tape and reel |
| RS-232 Standard Compliance | TIA/EIA-232-F |
| ITU Recommendation | ITU V.28 |
| Automotive Qualification | Qualified for automotive applications |
| Logic Supply Voltage | 3.3 V |
| Transceiver Configuration | 2/2 full-duplex |
| Manufacturer | Texas Instruments |
Hướng dẫn cấu hình chân MAX3232EIPWE4 16-tssop, 0.173 inch (4.40 mm) width
Cấu hình chân cho MAX3232EIPWE4 (16-tssop, 0.173 inch (4.40 mm) width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232EIPWE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232EIPWE4 phù hợp cho 6 Áp dụngs: Industrial Serial Console, Data-Acquisition Equipment, Printer and Peripheral Interface, Instrumentation and Test Systems, Embedded Service and Configuration Port, Network Equipment Management Port.
Industrial Serial Console
The MAX3232EIPWE4 fits an industrial console port because it provides two drivers, two receivers, and 250 kbps signaling in a 16-TSSOP package. Its 3 V to 5.5 V supply range allows connection to 3.3 V or 5 V controller logic, while the -40 °C to 85 °C rating supports equipment operating across industrial temperature conditions. The ±15-kV IEC ESD protection is especially useful where the console connector is exposed to human contact or long external cables. Place the charge-pump capacitors close to the IC and connect the driver outputs to the connector through the layout arrangement recommended in the datasheet.
Được đề xuất
Data-Acquisition Equipment
The MAX3232EIPWE4 can provide the RS-232 command link in data-acquisition systems that require a legacy-compatible serial interface. Its 250 kbps maximum rate is suitable for control commands, status reports, and configuration transfers rather than continuous high-volume measurement streaming. Two transmit and two receive channels allow bidirectional communication with external instruments. The device operates from 3 V to 5.5 V, simplifying interface design in mixed-voltage test equipment, while its industrial temperature range supports use in controlled factory or laboratory environments.
Được đề xuất
Printer and Peripheral Interface
The MAX3232EIPWE4 is appropriate for legacy printer, scanner, and industrial peripheral ports that still use TIA/EIA-232-F or ITU V.28 signaling. A maximum rate of 250 kbps covers typical command and status traffic, and the integrated ±15-kV IEC ESD protection improves resilience at a connector that may be repeatedly connected and disconnected. Using one transceiver IC avoids separate driver and receiver packages. Board layout should keep the external cable-side nets away from sensitive logic traces and preserve a direct chassis-to-digital-ground strategy appropriate to the overall equipment design.
Được đề xuất
Instrumentation and Test Systems
The MAX3232EIPWE4 fits instrumentation systems requiring a robust control port beside precision measurement circuitry. Its low-voltage supply operation permits use with 3.3 V control logic, and the -40 °C to 85 °C range supports laboratory and industrial test equipment. The RS-232 interface can be used for instrument configuration and diagnostic output while keeping the physical communication layer compact in a 16-TSSOP footprint. Because the transceiver converts logic levels to bipolar RS-232 signals internally, the host controller can use conventional digital I/O without adding separate level-shifting circuitry.
Được đề xuất
Embedded Service and Configuration Port
The MAX3232EIPWE4 provides a practical service port for embedded controllers that need configuration access, diagnostic logging, or firmware recovery through RS-232. Its 2/2 arrangement supports bidirectional command sessions, and the 250 kbps rate is more than sufficient for console traffic. Operation from 3 V to 5.5 V is helpful in mixed-voltage embedded boards, while the TSSOP package saves board area compared with larger discrete transceiver implementations. The ±15-kV IEC ESD protection adds connector-level robustness for equipment deployed outside a controlled laboratory environment.
Được đề xuất
Network Equipment Management Port
The MAX3232EIPWE4 can serve as a local RS-232 management interface on network equipment that also offers newer communication protocols. The interface remains useful for installation, diagnostics, and recovery procedures using legacy terminal equipment. Its 250 kbps capability handles management commands and diagnostic output, while the 16-TSSOP footprint supports compact line cards. The 3 V to 5.5 V supply range accommodates modern 3.3 V equipment, and ±15-kV IEC ESD protection helps withstand repeated connector contact. Grounding and cable routing remain critical because external RS-232 ports can introduce large transient voltages.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232EIPWE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232IPWG4 | MAX3232ECPWG4 | MAX3232ECPWE4 | SN65C3232EPWG4 |
|---|---|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Bảo phân biệt quan trọng
- Enhanced IEC ESD protection (vsMAX3232IPWG4)
- Industrial-temperature 2/2 transceiver (vsSN65C3232EPWG4)
- Low-voltage system compatibility (vsMAX3232ECPWE4)
Ghi chú thiết kế
Place the charge-pump capacitors and their associated traces directly beside the pins identified in the Texas Instruments datasheet. Keep these switching paths compact and away from receiver inputs and sensitive analog circuitry. Route the two driver outputs toward the external connector without long shared segments that could couple noise between ports.
Do not assume that every MAX3232 suffix has identical protection or temperature conditions. The E ordering option is associated with ±15-kV IEC ESD protection, while other family members can use different suffixes and protection levels. Confirm the complete ordering code, pinout, charge-pump capacitor values, and external component requirements before approving a substitution.
Provide a low-impedance ground plane connection and evaluate the relationship between board ground and connector shield according to the system grounding strategy. RS-232 receivers tolerate bipolar input signals, but poor grounding can increase errors and noise sensitivity. Place connector-side surge or ESD components where their transient current can return through a short, defined path.
The 250 kbps rating is adequate for control and diagnostic links but does not make the interface suitable for high-speed file transfer. Preserve the recommended charge-pump and bypass-capacitor layout, and avoid long stubs from the transceiver to the connector. If higher data rates are required, select an RS-232 transceiver explicitly rated for the target throughput.
Thông tin tuân thủ
Texas Instruments describes the MAX3232E family as qualified for automotive applications, but a specific AEC-Q100 grade and formal RoHS, REACH, lead-free, halogen-free, or conflict-minerals status were not stated in the available product information.