Maxim Integrated

MAX3243ECWI+ - 3V to 5.5V RS-232 Transceiver | Maxim

MPN: MAX3243ECWI+ ✓ Hoạt động
+3.0V to +5.5V Vdss 1 uA Id 28-pin SOIC Package
MOQ: 1 |

MAX3243ECWI+ Tóm tắt

The Maxim Integrated MAX3243ECWI+ is a 3V to 5.5V RS-232 transceiver with three transmitters, five receivers, full-duplex operation, and 15 kV ESD protection, housed in a 28-pin SOIC package. It is designed for systems that require multiple RS-232 data channels and low-power operation from a single 3.0V or 5.0V supply.

An RS-232 transceiver is an interface IC that combines line drivers, also called transmitters, and line receivers. The MAX3243 family provides three driver outputs and five receiver inputs in one package, allowing several serial ports or multiple logic signals to share a compact RS-232 interface. The MAX3243ECWI+ is intended for industrial, instrumentation, communications, and embedded-control equipment.

Key features include a 3.0V to 5.5V operating supply range, 1 uA supply current in shutdown mode, 120 kb/s data-rate capability in the comparison data, and integrated ESD protection rated to 15 kV. AutoShutdown functionality helps reduce system power consumption when the RS-232 interface is not required. The 28-pin SOIC package is a standard surface-mount industrial package.

The device uses RS-232 line signaling to translate digital logic levels into differential bipolar voltage levels and back again. The three transmitters support point-to-point serial links, while the five receivers can monitor incoming data or accept additional RS-232 signals. The integrated protection circuitry is particularly useful in industrial environments where cable-connected ports can be exposed to electrostatic discharge.

Typical applications include multi-port RS-232 equipment, test and measurement instruments, data acquisition systems, industrial controllers, and embedded serial interfaces. The MAX3243ECWI+ is appropriate when one board needs more than a single RS-232 transmitter and receiver while keeping the power supply below 5.5V.

For implementation, verify the supply voltage, confirm that the transceiver is enabled or disabled according to the system power sequence, and provide the required external charge-pump capacitors recommended by the manufacturer datasheet. Place protection and signal-routing components close to the connector and the transceiver to minimize ESD current paths.

Bộ thay thế dễ dàng lắp đặt cho MAX3243ECWI+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

MAX3243ECWI

✅ Drop-In
📦 28-pin SOIC
Ordering-code distinction only; the listed electrical configuration remains 3/5 full RS-232, 3.0V to 5.5V, and 28-pin SOIC, with 0% parameter difference

📋 Tham chiếu thay thế (không có trong danh mục)

SP3243EHCA-L/TR

✅ Drop-In
📦 28-pin SOIC
Pin-compatible functional equivalent; supply, data-rate, ESD, and capacitor requirements require comparison, with an estimated 0% functional-configuration difference

📋 Tham chiếu thay thế (không có trong danh mục)

MAX3243ECWI+ Thông số kỹ thuật

Product Type RS-232 transceiver
Supply Voltage Range +3.0V to +5.5V
Number of Transmitters 3
Number of Receivers 5
Duplex Type Full duplex
ESD Protection 15 kV
Tốc độ dữ liệu 120 kb/s
Shutdown Supply Current 1 uA
AutoShutdown Yes
Hộp 28-pin SOIC
Package Code SOP
Terminal Count 28
Kiểu lắp đặt Surface mount
Temperature Grade Commercial

Hướng dẫn cấu hình chân MAX3243ECWI+ sop

Cấu hình chân cho MAX3243ECWI+ (sop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân sop cho MAX3243ECWI+

Không có dữ liệu chân cụ thể sẵn có cho MAX3243ECWI+.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MAX3243ECWI+ phù hợp cho 6 Áp dụngs: Multi-Port Industrial RS-232 Interface, Test and Measurement Instrumentation, Data Acquisition and Control Equipment, Embedded Serial Communication Hub, Service and Configuration Port, Low-Voltage RS-232 Gateway.

🏭

Multi-Port Industrial RS-232 Interface

The MAX3243ECWI+ fits multi-port industrial equipment because one 28-pin SOIC provides three RS-232 transmitters and five receivers instead of requiring separate single-channel devices. Its 3.0V to 5.5V operating range supports both 3.3V and 5V control systems, while 15 kV ESD protection adds resilience at externally accessible connectors. Place the transceiver close to the connector, route protected lines directly to the relevant pins, and keep the charge-pump components on short, clean paths. The benefit is reduced board area and component count without sacrificing the channel count needed for configuration, diagnostics, and service interfaces.

🔧

Test and Measurement Instrumentation

The MAX3243ECWI+ is useful in test and measurement instruments that must communicate through several RS-232 ports. Three transmitter channels can control instruments or peripherals, while five receiver channels can acquire status and response data without requiring five separate receiver packages. Operation from a 3.0V to 5.5V supply lets the transceiver share either a legacy 5V rail or a modern 3.3V system rail. The listed 15 kV ESD protection is especially relevant for benchtop equipment connected to user-accessible cables. Maintain a controlled ground reference between connected equipment and follow the manufacturer capacitor recommendations for reliable charge-pump operation.

📡

Data Acquisition and Control Equipment

The MAX3243ECWI+ supports data-acquisition systems that combine command outputs with multiple status inputs. Its three transmitters can send commands to external controllers, and five receivers can read acknowledgements, interlocks, sensor states, or diagnostic signals. The 120 kb/s data-rate listing is suitable for moderate-speed supervisory communication, while the 3.0V to 5.5V supply range accommodates mixed-generation embedded hardware. AutoShutdown can lower consumption during idle intervals, and the 1 uA shutdown current helps battery-powered field equipment. Validate cable length, grounding, and signal integrity for the installed RS-232 environment rather than assuming logic-level timing applies directly.

🖥️

Embedded Serial Communication Hub

The MAX3243ECWI+ fits embedded serial communication hubs that must expose more than one legacy RS-232 port from a controller board. Three driver channels can connect to downstream equipment, while five receiver channels provide flexible input monitoring, and the 28-pin SOIC package remains easy to route on a conventional PCB. Its 3.0V to 5.5V compatibility supports direct operation from common embedded rails. AutoShutdown helps manage power when the serial subsystem is inactive. For robust implementations, assign unused channels deliberately, use the shutdown behavior intentionally, and place input and charge-pump paths away from clocks, switching converters, and high-current return paths.

🧩

Service and Configuration Port

The MAX3243ECWI+ can consolidate service, configuration, and diagnostic ports in industrial or communications equipment. A dedicated transmitter channel can carry service commands, additional transmitters can reach separate subsystems, and the five receiver inputs can collect equipment status without additional line-receiver ICs. The 15 kV ESD protection rating helps manage electrostatic exposure at service connectors, although connector-side protection remains important. The 3.3V-compatible supply range allows integration with modern logic. In a serviceable product, document channel assignments and shutdown states so maintenance personnel can interpret activity indicators and avoid simultaneous driver conflicts.

🌐

Low-Voltage RS-232 Gateway

The MAX3243ECWI+ is appropriate for a low-voltage gateway that bridges modern embedded electronics to multiple RS-232 devices. Three driver outputs support downstream equipment connections, while five receivers can capture incoming gateway or peripheral status. Its 1 uA shutdown current and AutoShutdown function improve power behavior in gateways that spend substantial time disconnected or idle. The 3.0V to 5.5V range also permits use in systems transitioning from 5V to 3.3V logic. Maintain defined signal grounds, avoid long unterminated branches, and check the manufacturer datasheet for external charge-pump capacitor values before release to production.

What is the MAX3243ECWI+?
The MAX3243ECWI+ is a 3.0V to 5.5V RS-232 transceiver from Maxim Integrated. It combines three transmitters, five receivers, full-duplex operation, AutoShutdown, and 15 kV ESD protection in a 28-pin SOIC package. The manufacturer product page identifies the MAX3243 as a production RS-232 transceiver family.
How many RS-232 transmitters and receivers does the MAX3243ECWI+ have?
The MAX3243ECWI+ provides three RS-232 transmitters and five receivers. This allows one device to support several outbound serial channels while also monitoring or receiving additional RS-232 signals. The 3/5 transceiver configuration is explicitly identified in the manufacturer product information.
What is the operating voltage of the MAX3243ECWI+?
The MAX3243ECWI+ operates from a +3.0V to +5.5V supply. This range makes the transceiver suitable for systems using either 3.3V or 5V rails, subject to the external charge-pump capacitor and operating requirements specified in the manufacturer datasheet.
Does the MAX3243ECWI+ support AutoShutdown?
Yes, the MAX3243ECWI+ supports AutoShutdown, and the comparison information lists a 1 uA shutdown supply current. The feature is useful in portable or intermittently connected equipment because it can reduce power consumption when the RS-232 interface is not active.
What data rate does the MAX3243ECWI+ support?
The comparison data lists the MAX3243ECWI+ for data rates up to 120 kb/s. The manufacturer product page identifies the MAX3243 family as a production 3V to 5.5V RS-232 transceiver with AutoShutdown. Verify the exact operating conditions and electrical limits in the manufacturer datasheet before finalizing a timing budget.
What ESD protection is built into the MAX3243ECWI+?
The MAX3243ECWI+ is listed with 15 kV ESD protection. This rating is useful for systems with externally accessible RS-232 connectors because it helps protect the transceiver from electrostatic-discharge events. The complete ESD system design should still include appropriate connector-side protection and layout practices.
Where can I download the MAX3243ECWI+ datasheet?
The official MAX3243 product page is the correct starting point for the manufacturer datasheet and product documentation. It identifies the MAX3243 family as a production +3V to +5.5V RS-232 transceiver with AutoShutdown. Use the MAX3243ECWI+ ordering information to identify the exact 28-pin SOIC configuration.
Where can I find the MAX3243ECWI+ pinout?
The MAX3243ECWI+ pinout is documented in the manufacturer datasheet linked from the official MAX3243 product page. The package is a 28-pin SOIC, also described as a 28-pin SOP with gull-wing leads. Use the pin-description table and package drawing together when assigning transceiver and charge-pump connections.
What is the best drop-in replacement for the MAX3243ECWI+?
The SP3243EHCA-L/TR is identified by the MaxLinear cross-reference information as a functional equivalent and pin-compatible replacement for the MAX3243ECWI+T. Confirm package, supply range, charge-pump values, ESD rating, and enable timing against the manufacturer datasheets before approving the substitution.
Can the SP3243EHCA-L/TR replace the MAX3243ECWI+?
The MaxLinear cross-reference listing identifies the SP3243EHCA-L/TR as functionally equivalent and pin compatible with the MAX3243ECWI+T. This makes it a relevant drop-in candidate for a MAX3243ECWI+ design, but the final substitution should still be checked for voltage, data-rate, ESD, and capacitor-value differences.
MAX3243ECWI+ versus SP3243EHCA-L/TR: which is better for a 3.3V design?
The MAX3243ECWI+ is the reference choice when its 3.0V to 5.5V supply range, 3/5 channel arrangement, and documented features are required unchanged. The SP3243EHCA-L/TR is listed as pin compatible and functionally equivalent, so it may simplify replacement sourcing. Confirm that the substitute supports the intended 3.3V rail and the original external capacitor configuration.
When should I choose the MAX3243ECWI+ over another RS-232 transceiver?
Choose the MAX3243ECWI+ when the design needs three transmitters, five receivers, a 3.0V to 5.5V supply, AutoShutdown, and a 28-pin SOIC footprint in one device. This channel count and low-voltage operation distinguish it from single-channel RS-232 transceivers and from multi-driver devices requiring a different package.
Is the MAX3243ECWI+ suitable for industrial RS-232 equipment?
The MAX3243ECWI+ is suitable for industrial RS-232 interfaces that require multiple channels, 3.3V or 5V operation, and connector-side ESD resilience. Its listed 15 kV ESD protection and surface-mount 28-pin SOIC package support robust embedded designs. Final compliance and temperature suitability must be confirmed against the exact ordering code.
How do I request a quote for the MAX3243ECWI+?
Use the Request a Quote form on this product page to request current pricing, availability, and lead time for the MAX3243ECWI+. The structured price evidence does not contain qualifying quantity-break pricing for the exact orderable MPN, so current commercial terms should be confirmed through that form.
What are the key specifications of MAX3243ECWI+ that engineers should know?
Key MAX3243ECWI+ specifications include a 3.0V to 5.5V supply range, three transmitters, five receivers, full-duplex operation, 120 kb/s data rate, 1 uA shutdown current, AutoShutdown, 15 kV ESD protection, and a 28-pin SOIC package. These parameters define its suitability for low-voltage multi-channel RS-232 equipment.

Dữ liệu tham khảo kỹ thuật cho MAX3243ECWI+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MAX3243ECWI+ when the board needs a three-transmitter, five-receiver RS-232 interface operating from a 3.3V or 5V rail in a 28-pin SOIC package. It is particularly attractive for industrial, test, data-acquisition, and service-port equipment that benefits from 15 kV ESD protection, AutoShutdown, and a listed 1 uA shutdown current. MAX3243ECWI is the closest same-manufacturer ordering option when the exact suffix distinction is the only change. Consider the SP3243EHCA-L/TR when sourcing flexibility matters and the MaxLinear cross-reference confirms the required electrical parameters. Approving that substitute requires checking the supply range, channel configuration, data rate, shutdown behavior, ESD rating, and external capacitor values against the original design.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này MAX3243ECWI SP3243EHCA-L/TR
Brand Maxim Integrated Maxim Integrated MaxLinear
Package 28-pin SOIC 28-pin SOIC 28-pin SOIC
Product Type RS-232 transceiver 3/5 full RS-232 transceiver RS-232 transceiver

Bảo phân biệt quan trọng

  • Integrated three-transmitter and five-receiver arrangement (vsSP3243EHCA-L/TR)
  • Low-voltage operation for mixed-generation systems (vsSP3243EHCA-L/TR)
  • Documented multi-channel protection and shutdown behavior (vsSP3243EHCA-L/TR)

Ghi chú thiết kế

Place the MAX3243ECWI+ charge-pump capacitors close to their associated pins and keep the associated traces short. Route RS-232 connector lines directly toward the transceiver and away from clocks, switching-converter nodes, and sensitive analog inputs. The 15 kV ESD rating is an internal device feature, not a replacement for connector-side protection or a controlled chassis-to-chassis ground strategy.

The MAX3243ECWI+ supports a +3.0V to +5.5V supply and includes a 1 uA shutdown supply-current specification. Confirm the system rail, enable state, and charge-pump operating requirements in the manufacturer datasheet before power-up. If AutoShutdown is used for intermittent operation, verify that signal states at the connector cannot back-power the transceiver during shutdown.

Do not treat the three transmitters as interchangeable outputs without checking the pin descriptions and intended channel assignments. Avoid connecting more than one transmitter to the same RS-232 node, and provide the manufacturer-recommended charge-pump capacitors with the specified voltage and tolerance. When substituting a pin-compatible device, recheck shutdown timing, ESD rating, data rate, and capacitor values.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product and comparison information identifies a commercial-temperature surface-mount component, but definitive RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses require confirmation from the manufacturer or an authorized compliance document.

Dữ liệu được xác minh vào: 2026-11-14 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MAX3243ECWI+ datasheet MAX3243ECWI+ pinout MAX3243ECWI+ datasheet pdf Maxim Integrated MAX3243ECWI+ MAX3243ECWI+ equivalent MAX3243ECWI+ replacement MAX3243ECWI+ vs SP3243EHCA-L/TR MAX3243ECWI+ 3.3V RS-232 MAX3243ECWI+ 28-SOIC MAX3243ECWI+ price MAX3243ECWI+ stock MAX3243ECWI+ industrial interface

Các bộ phận và thuật ngữ liên quan

Maxim Integrated MAX3243ECWI+ MAX3243ECWI SP3243EHCA-L/TR MaxLinear RS-232 RS-232 transceiver line transceiver interface IC semiconductor transmitter receiver AutoShutdown ESD protection 15 kV ESD full duplex 3.0V to 5.5V 120 kb/s 1 uA shutdown current 28-pin SOIC SOIC package surface mount industrial RS-232 charge-pump capacitor
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ