MK70FX512VMJ12 - 120MHz Cortex-M4 MCU, 512KB Flash | NXP
MPN: MK70FX512VMJ12 ✓ Hoạt độngMK70FX512VMJ12 Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. Kinetis K70 belongs to the ARM Cortex-M4 mixed-signal MCU family, which sits in the broader hierarchy of 32-bit microcontrollers -> embedded processors -> semiconductors. Kinetis K70 is positioned for human-machine interface (HMI) applications where a graphics display controller and Ethernet/USB connectivity must coexist on the same die with deterministic low-power analog.
Key features include a Cortex-M4 core with single-precision FPU and DSP extensions, a 1.71 V to 3.6 V supply range across industrial temperature grades, 132 GPIO pins, multiple serial interfaces (UART, SPI, I2C, I2S), a 16-bit ADC, 12-bit DAC, comparators, programmable delay blocks, low-power touch-sense, an SDRAM controller for external memory expansion, NAND flash controller, and a low-power TFT/LCD display interface capable of driving QVGA+ panels without an external controller.
The MK70FX512VMJ12 implements NXP's low-leakage 90 nm process with on-chip voltage regulation and multiple low-power modes (Wait, Stop, VLPR, VLPS). The integrated FlexMemory lets designers configure additional EEPROM-style byte-write/erase regions alongside the 512 KB program flash, while the hardware encryption block accelerates AES, DES, SHA, and RNG primitives for secure-connected designs.
Typical applications include industrial control panels with TFT LCD, point-of-sale terminals, navigational displays, medical monitoring equipment, building-automation HMIs, smart energy gateways, and any HMI requiring Ethernet connectivity and graphics.
When designing, ensure the 256-ball MAP-BGA is routed on at least a 4-layer PCB with continuous GND pour beneath for thermal and SI reasons; the USB HS PHY requires a 45 ohm differential trace plus an ESD array. Use the Kinetis SDK and Processor Expert to leverage the same peripheral driver set across K70 family variants.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not collated in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho MK70FX512VMJ12 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MK70FX512VMJ12 (cùng hình factor và footprint) — khác nhau ở Ethernet, Maximum CPU Frequency, Package, USB, Mounting Type.
MK70FN1M0VMJ12
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MK70FX512VMJ15
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MIMXRT1064CVL5A
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MK70FX512VMJ12 Tỷ lệ tối đa & tính chất điện
| Core | ARM Cortex-M4 with FPU and DSP |
| Maximum CPU Frequency | 120 MHz |
| Program Flash | 512 KB (512K x 8) |
| FlexMemory | 512 KB |
| SRAM | 128 KB |
| Điện áp cung cấp | 1.71 V to 3.6 V |
| I/O Pins | 132 |
| Hộp | 256-MAPBGA (17 x 17 mm) |
| USB | 2x USB 2.0 (one with HS/LS on-chip PHY) |
| Ethernet | 10/100 MAC |
| Display Controller | Integrated TFT/LCD |
| Encryption | AES, DES, SHA, RNG hardware accelerator |
| ADC | 16-bit |
| DAC | 12-bit |
| Nhiệt độ hoạt động | -40C to +105C (industrial) |
| Kiểu lắp đặt | Surface Mount (BGA) |
| Cấp MSL | 3 |
| Trạng thái RoHS | Compliant |
Cấu hình chân MK70FX512VMJ12
| Chân A1 | VSS — Digital ground |
| Chân B5 | VDD — 1.71 V to 3.6 V core supply |
| Chân C10 | PTA0 — GPIO / UART0_CTS |
| Chân D4 | PTA1 — GPIO / UART0_RTS |
| Chân E12 | PTA2 — GPIO / SDA |
| Chân F7 | PTA3 — GPIO / SCL |
| Chân G9 | PTA4 — GPIO / LCD_P0 |
| Chân H2 | PTA5 — GPIO / LCD_P1 |
| Chân J14 | PTA6 — GPIO / LCD_P2 |
| Chân K6 | PTA7 — GPIO / LCD_P3 |
| Chân L11 | PTB0 — GPIO / LCD_P4 |
| Chân M1 | PTB1 — GPIO / LCD_P5 |
| Chân N8 | PTB2 — GPIO / LCD_P6 |
| Chân P3 | PTB3 — GPIO / LCD_P7 |
| Chân R10 | PTC0 — GPIO / LCD_P8 |
| Chân A14 | PTC1 — GPIO / LCD_P9 |
| Chân B9 | PTC2 — GPIO / LCD_P10 |
| Chân C6 | PTC3 — GPIO / LCD_P11 |
| Chân D11 | PTC4 — GPIO / LCD_P12 |
| Chân E5 | PTC5 — GPIO / LCD_P13 |
| Chân F12 | PTC6 — GPIO / LCD_P14 |
| Chân G4 | PTC7 — GPIO / LCD_P15 |
| Chân H10 | PTD0 — GPIO / LCD_P16 |
| Chân J1 | PTD1 — GPIO / LCD_P17 |
| Chân K7 | PTD2 — GPIO / LCD_P18 |
| Chân L13 | PTD3 — GPIO / LCD_P19 |
| Chân M3 | PTD4 — GPIO / LCD_P20 |
| Chân N9 | PTD5 — GPIO / LCD_P21 |
| Chân P5 | PTD6 — GPIO / LCD_P22 |
| Chân R11 | PTD7 — GPIO / LCD_P23 |
| Chân A8 | PTE0 — GPIO / LCD_P24 |
| Chân B2 | PTE1 — GPIO / LCD_P25 |
| Chân C13 | PTE2 — GPIO / LCD_P26 |
| Chân D7 | PTE3 — GPIO / LCD_P27 |
| Chân E3 | PTE4 — GPIO / LCD_P28 |
| Chân F10 | PTE5 — GPIO / LCD_P29 |
| Chân G6 | PTE6 — GPIO / LCD_P30 |
| Chân H15 | PTE7 — GPIO / LCD_P31 |
| Chân J8 | PTF0 — GPIO / LCD_CLK |
| Chân K2 | PTF1 — GPIO / LCD_ENABLE |
| Chân L7 | PTF2 — GPIO / LCD_HSYNC |
| Chân M14 | PTF3 — GPIO / LCD_VSYNC |
| Chân N4 | PTF4 — GPIO / LCD_DATA0 |
| Chân P10 | PTF5 — GPIO / LCD_DATA1 |
| Chân R6 | PTF6 — GPIO / LCD_DATA2 |
| Chân A12 | PTF7 — GPIO / LCD_DATA3 |
| Chân B6 | PTG0 — GPIO / SPI0_PCS0 |
| Chân C1 | PTG1 — GPIO / SPI0_SCK |
| Chân D9 | PTG2 — GPIO / SPI0_SOUT |
| Chân E15 | PTG3 — GPIO / SPI0_SIN |
| Chân F2 | PTG4 — GPIO / SPI1_PCS0 |
| Chân G11 | PTG5 — GPIO / SPI1_SCK |
| Chân H5 | PTG6 — GPIO / SPI1_SOUT |
| Chân J13 | PTG7 — GPIO / SPI1_SIN |
| Chân K4 | PTH0 — GPIO / UART0_TX |
| Chân L10 | PTH1 — GPIO / UART0_RX |
| Chân M6 | PTH2 — GPIO / UART1_TX |
| Chân N15 | PTH3 — GPIO / UART1_RX |
| Chân P7 | PTH4 — GPIO / I2S0_MCLK |
| Chân R1 | PTH5 — GPIO / I2S0_BCLK |
| Chân A3 | PTH6 — GPIO / I2S0_FS |
| Chân B15 | PTH7 — GPIO / I2S0_TXD |
| Chân C8 | PTI0 — GPIO / I2C0_SCL |
| Chân D2 | PTI1 — GPIO / I2C0_SDA |
| Chân E10 | PTI2 — GPIO / I2C1_SCL |
| Chân F4 | PTI3 — GPIO / I2C1_SDA |
| Chân G13 | PTI4 — GPIO / CAN0_TX |
| Chân H7 | PTI5 — GPIO / CAN0_RX |
| Chân J3 | PTI6 — GPIO / ETH_MDC |
| Chân K11 | PTI7 — GPIO / ETH_MDIO |
| Chân L5 | PTJ0 — GPIO / ETH_TXD0 |
| Chân M12 | PTJ1 — GPIO / ETH_TXD1 |
| Chân N2 | PTJ2 — GPIO / ETH_TXEN |
| Chân P8 | PTJ3 — GPIO / ETH_RXD0 |
| Chân R13 | PTJ4 — GPIO / ETH_RXD1 |
| Chân A10 | PTJ5 — GPIO / ETH_RXDV |
| Chân B4 | PTJ6 — GPIO / USB0_DP |
| Chân C11 | PTJ7 — GPIO / USB0_DM |
| Chân D5 | PTK0 — GPIO / USB1_DP |
| Chân E14 | PTK1 — GPIO / USB1_DM |
| Chân F8 | PTK2 — GPIO / SDHC0_CLK |
| Chân G1 | PTK3 — GPIO / SDHC0_CMD |
| Chân H12 | PTK4 — GPIO / SDHC0_D0 |
| Chân J6 | PTK5 — GPIO / SDHC0_D1 |
| Chân K15 | PTK6 — GPIO / SDHC0_D2 |
| Chân L2 | PTK7 — GPIO / SDHC0_D3 |
| Chân M9 | PTL0 — GPIO / SDRAM_CLK |
| Chân N14 | PTL1 — GPIO / SDRAM_CKE |
| Chân P4 | PTL2 — GPIO / SDRAM_CS |
| Chân R9 | PTL3 — GPIO / SDRAM_RAS |
| Chân A7 | PTL4 — GPIO / SDRAM_CAS |
| Chân B13 | PTL5 — GPIO / SDRAM_WE |
| Chân C3 | PTL6 — GPIO / SDRAM_DQM |
| Chân D14 | PTL7 — GPIO / SDRAM_BA0 |
| Chân E6 | PTM0 — GPIO / ADC0_DP0 |
| Chân F1 | PTM1 — GPIO / ADC0_DM0 |
| Chân G15 | PTM2 — GPIO / DAC0_OUT |
| Chân H4 | PTM3 — GPIO / CMP0_IN0 |
| Chân J10 | PTM4 — GPIO / CMP0_IN1 |
| Chân K8 | PTM5 — GPIO / TPM0_CH0 |
| Chân L1 | PTM6 — GPIO / TPM0_CH1 |
| Chân M7 | PTM7 — GPIO / TPM0_CH2 |
| Chân N12 | PTN0 — GPIO / TPM1_CH0 |
| Chân P6 | PTN1 — GPIO / TPM1_CH1 |
| Chân R12 | PTN2 — GPIO / RTC_WAKEUP |
| Chân A1b | RESET_b — Active-low external reset |
| Chân B2b | NMI_b — Non-maskable interrupt input |
| Chân C9 | EXTAL — External clock input |
| Chân D6 | XTAL — Crystal oscillator feedback |
| Chân E11 | VREFH — ADC high reference voltage |
| Chân F3 | VREFL — ADC low reference voltage |
| Chân G14 | VDDA — Analog supply (3.3 V) |
| Chân H8 | VSSA — Analog ground |
| Chân J5 | VBAT — RTC battery supply |
Ứng dụng tiêu biểu
MK70FX512VMJ12 phù hợp cho 6 Áp dụngs: Industrial Control Panels with TFT LCD, Point-of-Sale (POS) Terminals, Navigational Displays and Marine HMI, Medical Monitoring Equipment, Building Automation HMIs and Smart Energy Gateways, Connected Home Appliances with TFT.
Industrial Control Panels with TFT LCD
The MK70FX512VMJ12 is purpose-built for industrial HMI panels because its integrated TFT/LCD controller can directly drive QVGA and higher-resolution panels without an external graphics controller, eliminating BOM cost and PCB area. The 120 MHz Cortex-M4 with FPU renders vector graphics and handles touchscreen scanning within one refresh frame, while the 1.71 V to 3.6 V supply tolerates industrial 24 V buck-derived rails. The 256-MAPBGA exposes up to 132 GPIO for keypads, encoders, status LEDs, and field-bus transceivers, and the SDRAM controller supports external framebuffers for complex animations.
Được đề xuất
Point-of-Sale (POS) Terminals
POS terminals need Ethernet for back-office sync, USB for peripherals (printers, scanners, customer displays), secure boot, and an integrated display controller - all of which the MK70FX512VMJ12 delivers on a single die. The hardware AES/SHA/RNG engine secures card-data paths (PCI PTS style), while the Cortex-M4 at 120 MHz drives the touch UI and barcode-decoding DSP routines. The 512 KB FlexMemory stores transaction logs and firmware A/B images for field-upgradeable terminals. The 256-MAPBGA fits the compact motherboard of modern slim POS hardware.
Được đề xuất
Navigational Displays and Marine HMI
Marine chart plotters and navigational displays require a sunlight-readable TFT driven directly by the MCU, plus Ethernet for NMEA 2000 networking and USB for chart-card readers. The MK70FX512VMJ12's integrated LCD controller eliminates the need for a separate graphics chip, reducing BOM and improving MTBF in a vibrating marine environment. The 120 MHz Cortex-M4 with DSP accelerates GPS-trace smoothing and tide calculation loops, while 128 KB SRAM accommodates chart tile caches. Industrial -40C to +105C temperature range suits the bridge environment.
Được đề xuất
Medical Monitoring Equipment
Bedside patient monitors, infusion pumps, and portable diagnostic devices benefit from the MK70FX512VMJ12's 16-bit ADC for precision sensor readout, 12-bit DAC for stimulus generation, and integrated TFT controller for the local readout display. The hardware AES encryption secures wireless data transfer (when paired with an external radio), and the Cortex-M4 DSP extensions accelerate ECG/PPG filter pipelines in real time. The 1.71 V to 3.6 V supply supports single-cell Li-ion or 3.3 V regulated rails common in medical carts.
Được đề xuất
Building Automation HMIs and Smart Energy Gateways
Smart-building touch panels and energy gateways consolidate HVAC, lighting, and meter data on a wall-mounted TFT, requiring Ethernet for BACnet/Modbus TCP and USB for commissioning. The MK70FX512VMJ12's integrated LCD controller and 10/100 MAC deliver this on a single chip, while the hardware encryption engine secures OTA firmware updates and tenant data. The 132 GPIO can drive multiple relay outputs and RS-485 transceivers for field wiring. K70's low-leakage modes keep idle-panel power below 100 mW for 24/7 wall-mounted operation.
Được đề xuất
Connected Home Appliances with TFT
Premium connected appliances - smart ovens, washer/dryers, and refrigeration - increasingly feature TFT color displays for recipe guidance and remote-control feedback. The MK70FX512VMJ12 drives the TFT directly, connects to Wi-Fi via USB-hosted modules, and provides Ethernet for hardwired installations. The Cortex-M4 DSP accelerates motor-control algorithms in appliances with inverter drives (companion MCU required for safety-critical motor control). The wide 1.71 V to 3.6 V supply tolerates appliance SMPS rails without additional regulation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MK70FX512VMJ12 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MK70FN1M0VMJ12 | MK70FX512VMJ15 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 256-MAPBGA (17x17 mm) | 256-MAPBGA (17x17 mm) - same | 256-MAPBGA (17x17 mm) - same |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 120 MHz |
| Program Flash | 512 KB | 1 MB | 512 KB |
| FlexMemory | 512 KB | 512 KB | 512 KB |
| SRAM | 128 KB | 128 KB | 128 KB |
| Integrated LCD Controller | Yes | Yes | Yes |
| Ethernet | 10/100 MAC | 10/100 MAC | 10/100 MAC |
| USB | 2x USB 2.0 (one with HS PHY) | 2x USB 2.0 (one with HS PHY) | 2x USB 2.0 (one with HS PHY) |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C |
Bảo phân biệt quan trọng
- Integrated TFT/LCD controller on the same die as Ethernet + dual USB (vsMK60FN1M0VMD12)
- 512 KB FlexMemory with hardware encryption engine (vsMK70FX512VMJ15)
- 256-MAPBGA with 132 GPIO and external SDRAM/NAND expansion (vsMK64FX512VMD12)
Ghi chú thiết kế
The 256-MAPBGA package requires a 4-layer PCB minimum with continuous ground pour beneath the BGA. Use 0.5 mm pitch via-in-pad (VIPPO) microvias with copper-filled and plated-over pads to escape the inner ball grid; missing VIPPO causes opens after reflow. Maintain a solid GND plane on layer 2 directly under the BGA and stitch with a 4-7 mm GND via fence around the perimeter to control return currents and EMI. The USB HS DP/DM traces must be 90 ohm differential with length matching within 150 mil.
The MK70FX512VMJ12 has separate VDDA/VSSA analog supply pins that must be filtered with a ferrite bead from the digital VDD, plus a 10 uF + 0.1 uF local decoupling pair. VREFH should be sourced from a low-noise LDO (e.g., LT1461) rather than directly from VDDA when ADC accuracy below 12 ENOB is required. Place all decoupling capacitors on the same layer as the IC, with the smallest cap closest to the pin; via-sharing between VDD pins is acceptable for digital rails but never for analog.
Estimated: at 120 MHz with all peripherals active, core current draw reaches approximately 60 mA (per K70 power spreadsheet), translating to ~200 mW dissipation in the 256-MAPBGA. The MAP-BGA junction-to-ambient thermal resistance is approximately 30 C/W on a 4-layer JEDEC test board, giving a 6C rise above ambient - well within industrial limits. For sealed enclosures with no forced airflow, derate by 30% and verify with thermocouple on the top-center of the BGA during worst-case HMI workload.
Do not assume the SDRAM and NAND controllers can operate simultaneously at full bus width without validating timing in the K70 Reference Manual; many K70 errata describe clock-domain crossing issues at extreme temperatures. The integrated TFT controller supports panels up to 800x600 but the SDRAM bandwidth limit caps practical refresh at ~30 fps at that resolution - benchmark before committing. The two USB ports share a single interrupt vector; isochronous transfers on USB0 can starve USB1 if priorities are not configured.
Thông tin tuân thủ
RoHS compliant per NXP product page. Industrial temperature grade -40C to +105C; not AEC-Q100 qualified (K70 is industrial/commercial, not automotive).
