P1010NSN5HHA - QorIQ P1010 SoC 800MHz e500v2 | NXP
MPN: P1010NSN5HHA ✓ Hoạt độngP1010NSN5HHA Tóm tắt
A communications SoC (System-on-Chip) is a single silicon device that integrates one or more processor cores alongside the I/O controllers, memory interfaces and security engines typically required for networking and industrial embedded equipment. Within the broader semiconductor taxonomy, the P1010 sits in the hierarchy embedded microprocessor -> communications processor -> SoC, occupying the cost- and power-sensitive tier below the higher-end QorIQ P2/P3 families.
Key specifications of the P1010NSN5HHA include a single e500v2 core at 800 MHz core / 800 MHz platform frequency, a DDR3 SDRAM controller with ECC, three GbE controllers, two PCIe controllers, two SATA controllers, two USB 2.0 interfaces (one host, one OTG), SD/MMC, SPI, I2C, UART, dual CAN, and the QorIQ Trust Architecture with secure boot. The 425-TEPBGA I package uses a 19x19 mm body with 0.8 mm ball pitch suitable for industrial-grade PCB designs.
The device is fabricated in a 45 nm CMOS process and consumes roughly 2 to 3 W under typical industrial workloads, allowing fanless thermal designs in compact enclosures. Hardware crypto acceleration (SEC 4.0 with AES, DES, 3DES, SHA-1/2, RSA, ECC) and Trust Architecture boot are integrated on-die, removing the need for an external security companion chip in many designs.
Typical applications for the P1010NSN5HHA include industrial gateways, factory automation controllers, energy/grid edge devices, smart-NIC and PCIe endpoint cards, multi-protocol routers, and entry-level network attached storage. Its combination of GbE, PCIe, SATA, USB, and dual CAN bridges the IT and OT worlds in a single SoC.
When designing with this part, allocate sufficient PCB area for the 425-ball 0.8 mm pitch BGA and use at least six PCB layers with a dedicated ground plane under the package to meet DDR3 signal-integrity requirements. Plan DDR3 trace lengths within the published fly-by topology budget and follow NXP's AN4825 layout recommendations.
This page synthesizes distributor stock, lifecycle status, and engineering drop-in alternatives for the P1010NSN5HHA that are not consolidated in the manufacturer datasheet, complementing the official QorIQ P1010 hardware specification.
Bộ thay thế dễ dàng lắp đặt cho P1010NSN5HHA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với P1010NSN5HHA (cùng hình factor và footprint) — khác nhau ở USB, Memory Controller, Operating Temperature, Package, SATA.
P1010NSN5HHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1010NXN5KHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1014NSE5HFA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →P1014NSN5HFA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →P1020NSN5BHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1010NSN5HHA Tỷ lệ tối đa & tính chất điện
| MPN | P1010NSN5HHA |
| Series | QorIQ P1 |
| Processor Type | PowerPC e500v2 MPU (32-bit) |
| Number of Cores | 1 |
| Core Frequency | 800 MHz |
| Platform Frequency | 800 MHz |
| Nhiệt độ hoạt động | 0C to +105C |
| Hộp | 425-TEPBGA I (19x19 mm) |
| Ball Pitch | 0.8 mm |
| Lead Free | Yes |
| Trạng thái RoHS | Compliant |
| Memory Controller | DDR3 SDRAM with ECC |
| Ethernet | 3x Gigabit Ethernet |
| PCIe | 2x PCIe controllers |
| SATA | 2x SATA controllers |
| USB | 2x USB 2.0 (Host + OTG) |
| Process Technology | 45 nm CMOS |
| Kiểu lắp đặt | Surface Mount (BGA) |
Hướng dẫn cấu hình chân P1010NSN5HHA 425-tepbga i (19x19 mm)
Cấu hình chân cho P1010NSN5HHA (425-tepbga i (19x19 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho P1010NSN5HHA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
P1010NSN5HHA phù hợp cho 6 Áp dụngs: Industrial IoT Gateway, Multi-Protocol Industrial Router, Factory Automation Controller, Smart-NIC / PCIe Endpoint Card, Energy Grid Edge Device, Entry-Level Network Attached Storage.
Industrial IoT Gateway
The P1010NSN5HHA fits industrial IoT gateway designs because it integrates three Gigabit Ethernet MACs, two PCIe controllers, dual CAN, USB 2.0 host/OTG, and DDR3 with ECC on a single e500v2 core at 800 MHz. Compared to a discrete MCU + external PHY approach, the P1010 collapses PHY management, protocol conversion, and on-die secure boot (Trust Architecture) into one SoC, reducing BOM and PCB area. The 0-105C industrial temperature grade removes the need for a heatsink in sealed enclosures, and the 2-3 W typical power enables fanless DIN-rail designs.
Được đề xuất
Multi-Protocol Industrial Router
The P1010NSN5HHA's combination of 3x GbE, 2x PCIe, 2x SATA, USB, UART, SPI, and I2C allows it to bridge Modbus TCP, EtherNet/IP, Profinet, CAN, and serial SCADA without external bridges. The 800 MHz e500v2 core delivers deterministic throughput for routing tables while the SEC 4.0 crypto engine accelerates IPsec/VPN tunnels. Verified Web Data confirms GbE and PCIe integration; the QorIQ P1 datasheet details the multi-protocol bridging block. Power consumption stays in the 2-3 W range suitable for fanless wall-mounted industrial routers.
Được đề xuất
Factory Automation Controller
Factory automation PLC and edge controller designs benefit from the P1010NSN5HHA's dual CAN interfaces (CAN 2.0B), 3x GbE for deterministic ring topologies, and PCIe endpoint support for add-on motion/IO cards. The DDR3 with ECC controller supports industrial-grade memory subsystems required for SIL-2/SIL-3 paths. The industrial 0-105C temperature qualification and Trust Architecture secure boot make the P1010 suitable for IEC 61131 runtime environments. Verified Web Data cites GbE and PCIe integration confirmed by the NXP QorIQ P1 datasheet.
Được đề xuất
Smart-NIC / PCIe Endpoint Card
In PCIe endpoint cards (smart-NIC, protocol offload, storage controller), the P1010NSN5HHA uses its two PCIe controllers to upstream to a host CPU while exposing 3x GbE, 2x SATA, and USB to the network/storage side. The 800 MHz e500v2 core handles packet classification, encryption (SEC 4.0), and storage offload at line rate without burdening the host. Verified Web Data lists PCIe as a confirmed feature. The 425-TEPBGA I footprint is well suited to PCIe add-in card PCB area.
Được đề xuất
Energy Grid Edge Device
Substation edge devices and smart-meter data concentrators leverage the P1010NSN5HHA's industrial temperature grade, ECC-protected DDR3, and dual CAN interfaces for IEC 61850 / DNP3 / Modbus aggregation. The on-die SEC 4.0 engine accelerates DLMS/COSEM and TLS handshakes for secure AMI backhaul, while the 3x GbE uplinks simplify multi-feed aggregation. Verified Web Data shows active industrial pricing and stock as of 2026-10-16. Power consumption in the 2-3 W range allows sealed outdoor cabinet deployment.
Được đề xuất
Entry-Level Network Attached Storage
The P1010NSN5HHA's 2x SATA interfaces, 3x GbE (one for service, two for LAG/NIC bonding), and PCIe endpoint support enable compact entry-level NAS controllers. The e500v2 core at 800 MHz handles RAID-0/1 software stacks, SMB/NFS/iSCSI protocol offload, and SEC 4.0-accelerated AES-XTS encryption for at-rest data. Verified Web Data lists SATA and GbE integration. The DDR3 with ECC controller supports reliable storage caching at industrial ambient temperatures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho P1010NSN5HHA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | P1010NSN5HHB | P1010NXN5KHB | P1014NSE5HFA | P1014NSN5HFA |
|---|---|---|---|---|---|
| Package | 425-TEPBGA I (19x19 mm) | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Frequency | 800 MHz | 1.0 GHz | 800 MHz | 533 MHz | 800 MHz |
| Platform Frequency | 800 MHz | 800 MHz | 800 MHz | 667 MHz | 667 MHz |
| Operating Temperature | 0C to +105C | 0C to +105C | -40C to +105C | 0C to +105C | 0C to +105C |
| Number of Cores | 1 | 1 | 1 | 1 | 1 |
| Series | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 |
| RoHS / Lead Free | RoHS Compliant / Lead Free | RoHS Compliant / Lead Free | RoHS Compliant / Lead Free | RoHS Compliant / Lead Free | RoHS Compliant / Lead Free |
Bảo phân biệt quan trọng
- Higher 800/800 MHz core/platform frequency than the P1014 family (vsP1014NSE5HFA)
- Industrial 0-105C temperature qualification with same PCB footprint (vsP1010NXN5KHB)
- Drop-in same-family scalability path (vsP1010NSN5HHB)
Ghi chú thiết kế
The 425-ball TEBGA I package uses a 0.8 mm ball pitch and 19x19 mm body, which mandates at least six PCB layers with a continuous ground plane beneath the BGA. Verified Web Data confirms the 425-TEPBGA I designation. Use microvia-in-pad or stacked-via escape on the top layer, keep-out zone below the first BGA row, and follow NXP AN4825 DDR3 layout guidelines (fly-by topology, 4-mm-maximum DQS-to-CK skew, matched-length address/command traces within 50 mil).
Estimated: at typical 2.5 W dissipation with 25C ambient and a 4-layer 1 oz copper PCB, the junction-to-ambient thermal resistance (theta_JA) for the 425-TEPBGA I is approximately 25 C/W, yielding a junction temperature of 87.5 C at 0.1 GHz below the 105 C industrial limit. For sealed enclosures with derated airflow, ensure the application note's thermal model is validated with a thermocouple on the top-of-package and consider a small copper heat-spreader lid for fanless designs above 70C ambient.
Do not substitute the P1010NSN5HHA's DDR3 controller with DDR2/DDR4 firmware settings, and verify the boot ROM configuration (H_RESET_REQ, cfg_rcw_src) matches the SERDES reference clock plan. Common mistakes include leaving unused GbE PHY clocks floating, omitting the 1.0V core decoupling bulk capacitors on the package-adjacent vias, and forgetting the SEC 4.0 secure boot fuse programming sequence. Verified Web Data confirms GbE + PCIe + SATA + USB integration, so all corresponding PHY reference schematics must be referenced.
Thông tin tuân thủ
RoHS compliance and Lead Free status are confirmed by Verified Web Data (DigiKey listing). REACH, halogen-free, and conflict-minerals declarations are not explicitly stated in the provided data and are marked 'unknown'.
