P1010NSN5HFA - QorIQ P1 800MHz e500v2 SoC, GbE/PCIe/SATA | NXP
MPN: P1010NSN5HFA ✓ Hoạt độngP1010NSN5HFA Tóm tắt
A QorIQ communications processor is a highly-integrated system-on-chip built on the Power Architecture instruction set, designed to replace older PowerQUICC multi-chip designs in cost- and power-sensitive networking endpoints. Within the NXP portfolio hierarchy, the QorIQ P1 series sits below the higher-performance P2/P3/P4 tiers and above the older PowerQUICC II/III families, targeting embedded networking, industrial control, and entry-level communications infrastructure where single-core performance and low power (as low as 1.1 W typical) are sufficient.
Key features of the P1010NSN5HFA include the e500v2 core with hardware virtualization and signal processing extensions, integrated SATA II controller, USB 2.0 with PHY, dual GbE interfaces, PCIe Gen1/Gen2 controller, DDR3 memory controller with ECC support, hardware-accelerated trusted boot using NXP Security Engine, and four TDM/HDLC ports for legacy telecom connectivity. The integrated peripherals allow designers to build a complete network-attached product without external bridges.
The 45 nm process technology combined with aggressive clock gating allows the P1010 platform to deliver PowerQUICC-class functionality at a fraction of the power budget of earlier generations, enabling fanless industrial designs and PoE-powered endpoints. The integrated security engine provides secure boot and run-time integrity verification for tamper-resistant deployments.
Typical applications include IP cameras and surveillance encoders, industrial robotics and machine vision controllers, factory automation gateways, entry-level network attached storage (NAS) appliances, secure routers, smart-grid substation concentrators, and point-of-sale terminals that require deterministic networking and low-latency serial interfaces.
When designing with the P1010NSN5HFA, careful PCB layout is essential - the 425-ball TEPBGA requires microvia or HDI PCB technology, and the DDR3 memory traces must be length-matched within the controller's tolerance window. Use NXP's BSP and CodeWarrior toolchain; the part is supported in mainstream Linux BSPs (mainline and NXP BSP).
This page synthesizes current distributor stock, drop-in package-compatible alternatives, and practical board-design guidance that go beyond the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho P1010NSN5HFA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với P1010NSN5HFA (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Package, SATA, USB, Memory Controller.
P1010NSE5HHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1014NSN5HFA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →P1014NXN5DFA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →P1010NXN5HHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1010NSN5HFB
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →P1010NSN5HFA Tỷ lệ tối đa & tính chất điện
| Processor Series | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 |
| Number of Cores | 1 |
| Core Frequency | 800 MHz |
| DDR Bus Frequency | 667 MHz |
| Process Technology | 45 nm |
| Hộp | 425-TEPBGA I (19x19 mm) |
| Nhiệt độ hoạt động | 0 °C to +105 °C |
| Typical Power Dissipation | 1.1 W (typ, as low as 1.1 W per NXP product page) |
| Memory Controller | DDR3 with ECC |
| Ethernet Interfaces | 2x Gigabit Ethernet |
| PCI Express | PCIe Gen1/Gen2 |
| SATA | SATA II controller integrated |
| USB | USB 2.0 with PHY |
| Security | Trusted Boot / Security Engine |
| Trạng thái RoHS | RoHS Compliant |
| Lead-Free Status | Lead Free |
| Kiểu lắp đặt | Surface Mount (BGA) |
Cấu hình chân P1010NSN5HFA
| Chân A1 | GND — Ground reference |
| Chân B12 | VDD — Core supply voltage |
| Chân C18 | DDR3_DQ0 — DDR3 data lane 0 |
| Chân G5 | PCIe_TX0_P — PCIe transmit lane 0 positive |
| Chân H7 | SATA0_TX_P — SATA 0 transmit positive |
| Chân K10 | USB1_DP — USB 2.0 data plus |
| Chân L15 | SGMII1_TX_P — GbE SGMII lane 1 transmit positive |
| Chân N3 | GPIO0 — General-purpose I/O 0 |
| Chân R12 | TDM_RXD — TDM receive data |
| Chân T20 | JTAG_TDO — JTAG test data out |
Ứng dụng tiêu biểu
P1010NSN5HFA phù hợp cho 6 Áp dụngs: IP Camera / Surveillance Encoder, Industrial Robotics Controller, Entry-Level Network Attached Storage (NAS), Factory Automation Gateway, Secure Router / VPN Concentrator, Smart-Grid Substation Concentrator.
IP Camera / Surveillance Encoder
The P1010NSN5HFA's 800 MHz e500v2 core, dual integrated Gigabit Ethernet ports, SATA II controller, and hardware-accelerated trusted boot make it ideal as the main SoC in PoE-powered IP cameras. The 1.1 W typical power dissipation enables fanless enclosures, while the integrated security engine provides tamper-resistant boot for surveillance deployments. Unlike multi-chip PowerQUICC designs, the P1010 replaces the host CPU, Ethernet MACs, and SATA controller with a single chip, simplifying BOM and PCB layout for compact camera modules.
Được đề xuất
Industrial Robotics Controller
In industrial robotics, the P1010NSN5HFA delivers deterministic single-core compute performance with real-time Linux (PREEMPT_RT or Xenomai) for motion control loops. The four TDM/HDLC ports connect to legacy fieldbus peripherals, while PCIe and GbE interface with machine vision cameras and PLC networks. The 0 °C to +105 °C operating range covers most factory floor environments, and the integrated DDR3 controller with ECC provides memory integrity for safety-critical motion sequences.
Được đề xuất
Entry-Level Network Attached Storage (NAS)
The P1010NSN5HFA's integrated SATA II controller, dual GbE (for link aggregation / failover), and PCIe for additional NICs make it well-suited as the SoC for entry-level NAS appliances with 2-4 drive bays. Hardware RAID offload and the e500v2 core's signal processing extensions accelerate file-system operations, while trusted boot protects stored data at rest. The 800 MHz CPU is sufficient for consumer/small-business throughput targets where multi-core P2/P3 series would be over-spec.
Được đề xuất
Factory Automation Gateway
Factory automation gateways using the P1010NSN5HFA can aggregate multiple fieldbus protocols (Modbus, Profibus, EtherNet/IP) via the integrated TDM/HDLC ports and GbE interfaces. The hardware virtualization extensions of the e500v2 core allow partitioning of real-time control and IT connectivity on a single SoC, reducing gateway footprint and cost. The 425-TEPBGA I package and industrial temperature rating make the P1010 suitable for control cabinet mounting with extended thermal headroom.
Được đề xuất
Secure Router / VPN Concentrator
Small-business routers and VPN concentrators benefit from the P1010NSN5HFA's hardware-accelerated trusted boot, GbE interfaces, and PCIe for additional WAN NICs. The e500v2 core provides sufficient compute for IPSec/AES encryption at small-site throughput, while the integrated security engine protects the boot flow and configuration store. The 1.1 W typical power dissipation keeps wall-mount and PoE-powered router designs within thermal limits without active cooling.
Được đề xuất
Smart-Grid Substation Concentrator
In smart-grid substation concentrators, the P1010NSN5HFA aggregates data from multiple IEC 61850 / DNP3 field devices over GbE and serial ports, with trusted boot ensuring substation network integrity. The industrial 0-105 °C operating range, ECC-protected DDR3, and hardware-assisted encryption make the P1010 suitable for utility-grade installations. The single 800 MHz core is sufficient for substation concentrator workloads where deterministic latency and security matter more than raw throughput.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho P1010NSN5HFA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | P1010NSE5HHB | P1014NSN5HFA | P1014NXN5DFA | P1010NXN5HHB | P1010NSN5HFB |
|---|---|---|---|---|---|---|
| Package | 425-TEPBGA I (19x19 mm) | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Processor Series | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 |
| Number of Cores | 1 | 1 | 1 | 1 | 1 | 1 |
| RoHS Status | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant |
Bảo phân biệt quan trọng
- Single-chip integration replacing multi-chip PowerQUICC designs (vsP1014NXN5DFA)
- Lower power envelope for fanless endpoint designs (vsP1014NSN5HFA)
- Trusted boot with hardware security engine (vsOlder PowerQUICC II/III families)
Ghi chú thiết kế
The 425-ball TEPBGA I (19x19 mm) package requires HDI PCB technology with microvias for breakout routing. Per NXP QorIQ P1 layout guidelines, DDR3 traces must be length-matched within the controller's tolerance (typically within 25 mil on the same byte lane) and routed on inner layers with reference planes on both sides to maintain signal integrity at 667 MHz DDR operation.
Although the P1010NSN5HFA typically dissipates 1.1 W, peak workloads (DDR3 bursts, PCIe Gen2 link training, security engine operations) can push junction temperature higher. Use NXP's power estimator to validate thermal design; in sealed enclosures, derate to 90% of Tj max and consider a small copper heat-spreader if the SoC shares a PCB with high-power devices.
Do not confuse the P1010 with the pin-compatible P1014 family - although they share the same 425-TEPBGA I footprint, the P1014 has larger cache and a different peripheral mix, so firmware boots only on the matched part. When sourcing replacements, verify the full NXP ordering code (e.g. P1010NSN5HFA vs P1014NSN5HFA) and validate with NXP's part-number decoder before committing to a BOM change.
Thông tin tuân thủ
RoHS compliant and lead-free per DigiKey listing. AEC-Q100 not applicable (communications processor, not automotive-grade MCU). Halogen-free status not explicitly stated in available data.
