PCM1755DBQ - 24-Bit 106dB Stereo DAC | Texas Instruments
MPN: PCM1755DBQ ✓ Hoạt độngPCM1755DBQ Tóm tắt
An audio DAC is the final conversion stage in a digital audio signal chain. It receives sampled and encoded audio from a digital processor, reconstructs the analog voltage waveform, and drives an audio amplifier, mixer, headphone stage, or line output. PCM1755DBQ belongs to the stereo DAC, audio converter, interface IC, and semiconductor hierarchy, with a software-control interface supporting programmable operating functions.
The converter delivers 24-bit resolution with 106 dB typical SNR and 0.002% typical THD+N when operated from a 5 V supply. Its 4 VPP typical full-scale output provides useful headroom for subsequent analog stages. A four-times or eight-times oversampling digital filter and -50 dB stop-band attenuation help reject out-of-band content before the analog output stage.
PCM175x uses TI's enhanced multilevel delta-sigma architecture with fourth-order noise shaping and eight-level amplitude quantization. This architecture improves clock-jitter tolerance while maintaining high audio resolution. The PCM1755 can operate under hardware control or through a three-wire serial port that provides register-write access to user-programmable functions.
Typical uses include professional audio equipment, digital mixers, multichannel sound systems, home-theater receivers, active speakers, and USB or network audio playback platforms. The converter is particularly useful where two low-noise analog channels are required but a conventional stereo DAC implementation would be unnecessarily complex.
The primary design consideration is clean, stable power for the converter and careful routing of digital clock and data signals away from the analog outputs. Follow the manufacturer datasheet for the pin-description table, recommended decoupling network, analog output implementation, and supported serial-control configuration.
This product page consolidates the PCM1755DBQ specifications, sourcing information, application guidance, and verified drop-in alternatives. It also provides practical design notes for clocking, filtering, power, and output implementation that help engineers evaluate the converter before completing a board-level audio design.
Bộ thay thế dễ dàng lắp đặt cho PCM1755DBQ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PCM1755DBQ (cùng hình factor và footprint) — khác nhau ở Control Interface, Dynamic Range, Maximum Sampling Rate, Package, Signal-to-Noise Ratio.
PCM1755DBQG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1754DBQ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PCM1754DBQG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1753DBQ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PCM1755DBQ Tỷ lệ tối đa & tính chất điện
| Device Type | Stereo audio digital-to-analog converter (DAC) |
| Độ phân giải | 24 bit |
| Number of Channels | 2 channels |
| Maximum Sampling Rate | 200 kHz |
| Digital Audio Interface | I2S |
| Signal-to-Noise Ratio | 106 dB typical at 5 V |
| Dynamic Range | 106 dB at 5 V |
| Total Harmonic Distortion plus Noise | 0.002% typical at 5 V |
| Full-Scale Output | 4 VPP typical |
| Digital Filter Oversampling Ratio | 4x or 8x |
| Stop-Band Attenuation | -50 dB |
| Architecture | Enhanced multilevel delta-sigma with fourth-order noise shaping and eight-level amplitude quantization |
| Control Interface | Three-wire serial control port with register-write functions |
| Điện áp cung cấp | 5 V |
| Hộp | 16-pin SSOP |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân PCM1755DBQ 16-pin ssop
Cấu hình chân cho PCM1755DBQ (16-pin ssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho PCM1755DBQ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCM1755DBQ phù hợp cho 6 Áp dụngs: Digital Mixing Console, Professional Audio Monitor, Home-Theater Receiver, Active Speaker USB DAC, Multichannel Sound System, Recording and Broadcast Equipment.
Digital Mixing Console
PCM1755DBQ fits a digital mixing console because it converts two 24-bit audio channels into analog line-level signals while supporting sampling rates up to 200 kHz. Its 106 dB typical SNR and 0.002% typical THD+N provide useful dynamic-range margin for mix-bus and monitor paths. The converter can accept I2S data from an audio DSP, while its software-control port supports programmable operating functions. A typical signal chain uses the DAC outputs as the bridge between the digital mixer matrix and analog line amplifiers. Because the available full-scale output is 4 VPP, downstream amplifier gain and headroom must be planned around that level. Keep the I2S clock and data traces away from the analog outputs to preserve the converter's noise and distortion performance.
Được đề xuất
Professional Audio Monitor
PCM1755DBQ is appropriate for a two-channel powered monitor when the source is digital and a high-quality stereo reconstruction is required. The 24-bit resolution preserves detailed digital source information, while the 200 kHz sampling capability supports high-rate multichannel workflows. The converter's 106 dB typical dynamic range and 0.002% typical THD+N help maintain a low noise and distortion floor before the power amplifier. The 4 VPP typical output should drive the monitor's input stage through the network recommended in the manufacturer datasheet. Separating digital clocking and I2S routing from the analog output section is especially important because switching artifacts can become audible in nearfield monitoring systems.
Được đề xuất
Home-Theater Receiver
PCM1755DBQ can serve as a stereo auxiliary or main-channel DAC in a home-theater receiver that accepts digital audio from an HDMI or network-audio processor. Its two-channel 24-bit architecture covers left and right channels, and its support for sampling rates up to 200 kHz accommodates high-resolution audio streams after appropriate format conversion. The typical 106 dB SNR provides a useful dynamic-range budget for cinematic and music playback. Use the three-wire serial interface when programmable behavior is required, or hardware mode where the application needs simpler control. The receiver's analog volume-control and line-output circuitry must accommodate the 4 VPP full-scale output without clipping and should follow the converter's recommended output network.
Được đề xuất
Active Speaker USB DAC
PCM1755DBQ is suitable for an active-speaker USB or network-audio DAC card because it provides a compact two-channel bridge from digital audio data to analog speaker input. A 24-bit converter with 200 kHz maximum sampling rate supports common high-resolution playback formats after the host formats the data correctly. The 106 dB typical SNR and 0.002% typical THD+N are beneficial in a quiet listening environment where the converter's own noise can be exposed by efficient speakers. A dual audio amplifier can follow the DAC, but its gain must match the 4 VPP typical converter output. Place the 5 V decoupling network close to the device and isolate the analog output routing from USB data, clocks, and switching regulators.
Được đề xuất
Multichannel Sound System
PCM1755DBQ can contribute two channels to a multichannel sound system by deploying multiple stereo converter instances for front, surround, or height-speaker pairs. Its 24-bit processing and support for sampling rates up to 200 kHz allow it to accept high-rate digital audio channels after system routing. The 106 dB typical dynamic range supports consistent channel-to-channel performance, while the 0.002% typical THD+N specification helps avoid adding audible distortion in distributed speaker installations. Each converter requires synchronized clock and serial-data routing to prevent channel timing errors. Keep each device's analog section compact and use a common, quiet power strategy, while observing the manufacturer's grounding and decoupling recommendations around every SSOP.
Được đề xuất
Recording and Broadcast Equipment
PCM1755DBQ is appropriate for playback and monitoring paths in recording or broadcast equipment that require a compact, high-resolution stereo DAC. Its 200 kHz maximum sampling rate supports high-rate studio workflows, while the typical 106 dB SNR and 0.002% THD+N support transparent reconstruction of the digital source. The three-wire serial port allows software-addressable configuration when a host processor needs programmable functions. Analog monitoring paths should account for the converter's 4 VPP full-scale output and terminate them through the documented output network. In a studio environment, keep clock jitter and power-supply noise under control by following the recommended reference layout, using a stable 5 V rail, and isolating digital return currents from the analog output region.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCM1755DBQ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCM1755DBQG4 | PCM1754DBQ | PCM1754DBQG4 | PCM1753DBQ |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP |
| Device Type | Stereo audio DAC | Stereo audio DAC | Stereo audio DAC | Stereo audio DAC | Stereo audio DAC |
| Resolution | 24 bit | 24 bit | 24 bit | 24 bit | 24 bit |
Bảo phân biệt quan trọng
- Documented high-resolution performance (vsPCM1754DBQ)
- High-rate stereo conversion (vsPCM1753DBQ)
- Programmable control in a 16-pin SSOP (vsPCM1754DBQG4)
- Directly compatible ordering variant (vsPCM1755DBQG4)
Ghi chú thiết kế
PCM1755DBQ operates from a 5 V supply, so the converter should be connected to a low-noise rail with local high-frequency decoupling placed directly at the supply and ground pins. Use the capacitor values and grounding arrangement specified in the manufacturer application circuit. Keep switching-regulator loops and inductor nodes away from the analog output section because supply ripple can degrade the converter's 106 dB typical SNR and 0.002% typical THD+N performance.
Separate the I2S data, sampling-clock, and serial-control routes from the analog output traces. Route clocks away from OUTA and OUTB, use a continuous ground reference, and avoid running digital signals beneath the analog outputs or the associated passive components. The SSOP footprint is fine-pitch, so verify pin-one orientation and every net against the manufacturer pin-description table before fabrication.
Clock quality directly affects digital-to-analog reconstruction, even though the enhanced multilevel delta-sigma architecture improves jitter tolerance. Deliver the supported system and sampling clocks from a low-jitter source, observe the timing limits in the manufacturer datasheet, and avoid adding unnecessary buffers or long stubs between the audio processor and PCM1755DBQ. Validate the complete interface with an oscilloscope or audio analyzer after layout.
Do not treat a same-package family member as interchangeable without checking software-control registers, pin 5 behavior, clock requirements, and output circuitry. PCM1755DBQG4 is the closest ordering variant, while PCM1754DBQ and PCM1753DBQ can differ in performance or control behavior. Confirm the exact function of all 16 pins and the external analog network against the relevant manufacturer datasheet before substituting a part.
Thông tin tuân thủ
Compliance details are not stated in the available manufacturer and distributor information. The G4 ordering suffix is shown for PCM1755DBQG4, but it is not interpreted here as proof of a specific compliance declaration.