PIC24F08KA101-E/SS - 16-Bit 32MHz XLP Microcontroller | Microchip
MPN: PIC24F08KA101-E/SS ✓ Hoạt độngPIC24F08KA101-E/SS Tóm tắt
Bộ thay thế dễ dàng lắp đặt cho PIC24F08KA101-E/SS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC24F08KA101-E/SS (cùng hình factor và footprint) — khác nhau ở I/O Pins, Package.
PIC24F08KA101-I/SS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24F08KA101-E/SS Tỷ lệ tối đa & tính chất điện
| Architecture | 16-bit PIC microcontroller |
| Program Memory | 8 KB flash (2.75K x 24) |
| RAM | 1.5 KB (1.5K x 8) |
| Maximum CPU Frequency | 32 MHz |
| I/O Pins | 18 |
| Hộp | 20-pin SSOP |
| Kiểu lắp đặt | Surface mount |
| Oscillator | Internal |
| Low-Power Technology | XLP eXtreme Low Power |
| Deep-Sleep Features | DSBOR, DSWDT, RTCC |
| Serial EEPROM | 512 bytes |
| ADC | 1 ADC |
| Packaging | Tube |
| Manufacturer | Microchip Technology |
Hướng dẫn cấu hình chân PIC24F08KA101-E/SS 20-pin ssop
Cấu hình chân cho PIC24F08KA101-E/SS (20-pin ssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho PIC24F08KA101-E/SS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PIC24F08KA101-E/SS phù hợp cho 6 Áp dụngs: Battery-powered Sensor Node, Portable Environmental Monitor, Industrial Control Module, Low-Power Data Logger, Smart Home Sensor Interface, Compact Power-Supply Controller.
Battery-powered Sensor Node
PIC24F08KA101-E/SS fits compact battery-operated sensor nodes because its XLP design targets low active and sleep consumption, while the 16-bit processor provides more control capability than an 8-bit MCU. The 8 KB flash memory stores application firmware, 1.5 KB RAM supports short acquisition and processing buffers, and 18 I/O pins connect sensors and indicators. Firmware can use DSBOR, DSWDT, and RTCC to coordinate low-power states and reliable wake-up behavior. The principal design trade-off is that actual battery life depends on duty cycle, sensor current, active processor time, and the external regulator, so developers should measure the complete load profile rather than relying on MCU current alone.
Được đề xuất
Portable Environmental Monitor
The PIC24F08KA101-E/SS is appropriate for portable temperature, humidity, and environmental monitoring products because it combines 32 MHz processing, one ADC, 18 I/O pins, and XLP low-power features in a 20-pin SSOP. The MCU can sample sensors, perform threshold decisions, and store state in flash while spending much of its operating life in a low-power mode. The 16-bit architecture improves arithmetic efficiency for compensation and filtering, while DSBOR and DSWDT support safer behavior during low-battery conditions. Product teams must still verify the ADC accuracy and voltage range required by their sensors and should account for the current drawn by the sensor, regulator, status indicator, and communication module.
Được đề xuất
Industrial Control Module
PIC24F08KA101-E/SS can serve as the control core in a compact industrial module requiring deterministic peripheral handling and low standby consumption. Its 32 MHz maximum operating speed and 16-bit architecture support responsive control tasks, while 18 I/O pins provide interfaces for sensors, digital inputs, indicators, and actuators. The XLP feature set helps modules reduce power during idle periods, especially in distributed equipment where continuous mains connectivity is undesirable. Temperature-grade selection is critical: the verified I/SS comparison reaches 125°C, whereas the E/SO comparison reaches 85°C. Engineers should confirm the exact E/SS limits and use isolation, surge protection, and suitable industrial connectors where the environment requires them.
Được đề xuất
Low-Power Data Logger
PIC24F08KA101-E/SS is well suited to a low-power data logger because 8 KB flash provides embedded firmware storage, 1.5 KB RAM can hold acquisition buffers, and the XLP architecture supports duty-cycled operation. The 18 available I/O pins can accommodate an I2C or SPI sensor, a serial memory interface, a real-time-clock connection, and a status indicator, subject to the device's verified peripheral assignments. DSWDT supports supervised recovery from unexpected stalls, while DSBOR assists controlled behavior as the supply declines. For reliable records, firmware should timestamp events and commit data in a way that respects flash endurance. The exact write timing, retention, and cycle characteristics must be taken from the Microchip datasheet.
Được đề xuất
Smart Home Sensor Interface
PIC24F08KA101-E/SS can act as a dedicated low-power interface between analog sensors and a home or building network. The one ADC supports analog measurement, the 18 I/O pins provide sensor and communication connections, and the 16-bit core can perform filtering and threshold logic before forwarding compact data. XLP operation is valuable in battery-powered nodes because the MCU can remain asleep between updates, reducing the load compared with a continuously active general-purpose processor. A practical implementation should define the communication duty cycle, isolate noisy actuators from sensitive measurement traces, and ensure the external regulator remains efficient at light loads. Network protocol support and exact peripheral multiplexing must be verified against the datasheet before board release.
Được đề xuất
Compact Power-Supply Controller
PIC24F08KA101-E/SS can manage a compact power subsystem by monitoring inputs, sequencing rails, controlling indicators, and coordinating fault responses. Its 16-bit architecture and 32 MHz maximum speed provide ample control throughput, while 18 I/O pins can support digital monitoring, enable signals, and status outputs. Low-power XLP modes are useful when the managed system spends long intervals inactive. The MCU should not be treated as a replacement for dedicated analog protection or power-conversion circuitry; instead, it can supervise external converters and react to measured conditions. Engineers must verify ADC input limits, switching-pin behavior, and the available timing functions in the selected package, then provide suitable input filtering and protection on field-connected nodes.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC24F08KA101-E/SS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC24F08KA101-I/SS |
|---|---|---|
| Package | 20-pin SSOP | 20-pin SSOP |
| Brand | Microchip Technology | Microchip Technology |
| Architecture | 16-bit PIC microcontroller | 16-bit PIC microcontroller |
| Program Memory | 8 KB flash (2.75K x 24) | 8 KB flash (2.75K x 24) |
| RAM | 1.5 KB (1.5K x 8) | 1.5 KB (1.5K x 8) |
| Maximum CPU Frequency | 32 MHz | 32 MHz |
| I/O Pins | 18 | 18 |
| ADC Count | 1 ADC | 1 ADC |
| Low-Power Features | XLP, DSBOR, DSWDT, RTCC | PIC XLP family device |
Bảo phân biệt quan trọng
- Higher-grade temperature option in the verified replacement (vsPIC24F08KA101-E/SS)
- Pin-compatible family configuration (vsPIC24F08KA101-I/SS)
- Low-power system integration (vsPIC24F08KA101-I/SS)
Ghi chú thiết kế
Estimate the complete power budget rather than the PIC24F08KA101-E/SS current alone. Include the sensor, regulator quiescent current, communications activity, indicator drive, and leakage paths. Then use the verified XLP, DSBOR, DSWDT, and RTCC features to define the sleep and wake-up strategy. Do not publish a battery-runtime claim until it has been measured with the intended firmware, supply voltage, temperature, and accessory load.
Place the MCU, decoupling capacitors, oscillator components, and programming or debug connections according to the official Microchip pin configuration and layout guidance. Keep analog sensor traces away from switching nodes and high-current paths, and provide a low-impedance ground reference for the ADC. The supplied excerpts do not include the complete pin table or exposed-pad connection details, so verify those points in the manufacturer datasheet before fabrication.
Do not substitute PIC24F08KA101-I/SS solely because the package matches. The verified comparison shows a temperature-grade distinction, and the E/SS device's exact operating limits were not included in the source excerpts. Confirm supply voltage, maximum frequency, ADC limits, temperature range, pin multiplexing, and programming configuration for the exact suffix before approving a drop-in replacement.
The SSOP footprint has closely spaced leads, so inspect the land pattern against the official package drawing rather than relying on a generic SSOP footprint. Verify lead pitch, pin-1 orientation, solder-mask clearance, and the handling of any thermal or exposed pad. Use a qualified assembly process and inspect joints with adequate magnification because incorrect lead alignment can cause intermittent or permanent failures.
Thông tin tuân thủ
The supplied verified excerpts do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than assuming compliance. The -E ordering suffix is identified as a temperature-grade designation, but no specific automotive qualification was provided.
