SPC5643LFF2MLL6 - 32-bit Dual-Core 64MHz MCU, 1MB Flash | NXP
MPN: SPC5643LFF2MLL6 ✓ Hoạt độngSPC5643LFF2MLL6 Tóm tắt
An automotive microcontroller is the central embedded processor of a vehicle electronic control unit, integrating CPU cores, flash and SRAM memory, communication peripherals, and safety mechanisms on a single die. Within the hierarchy of embedded processors, the MCU sits below application processors but above bare logic, and within NXP's portfolio the SPC5643L belongs to the MPC56xx / Qorivva family of Power Architecture MCUs targeted at body, gateway, and safety applications.
Key features include a dual e200z4 32-bit core subsystem running at 64 MHz, 1 MB (1M x 8) of on-chip flash for code and calibration data, and integrated connectivity covering CANbus, FlexRay, LINbus, SPI, and UART/USART. Peripheral support for DMA, PWM, watchdog timer (WDT), and power-on reset (POR) reduces external component count.
The Dual Power Architecture places key functional safety features - such as redundant power domains and safety-oriented peripherals - on one chip, reducing design complexity for safety-relevant ECUs. The e200z4 core implements the Power Architecture (Book E) instruction set, giving access to a mature toolchain including NXP's SPC5 Studio and third-party compilers.
Typical applications include automotive body control modules, gateway nodes bridging CAN, LIN, and FlexRay networks, and industrial control systems that demand -40 C to +125 C operation and automotive-grade qualification. The QFP-100 footprint suits cost-sensitive two-layer routing of high-pin-count MCUs.
When designing with this MCU, budget flash allocation carefully: the full 1 MB is shared by application code, boot code, and calibration data, and FlexRay use requires dedicated RAM and scheduling headroom.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho SPC5643LFF2MLL6 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với SPC5643LFF2MLL6 (cùng hình factor và footprint) — khác nhau ở Connectivity, Package, Operating Temperature, Supply Voltage, Core Architecture.
SPC5643LFF2MLQ1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SPC5606BF1VLU6R
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SPC5602BF2MLL6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SPC5516GBMLQ66
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →SPC5553MVR132
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →SPC5643LFF2MLL6 Tỷ lệ tối đa & tính chất điện
| Core Processor | e200z4 (Power Architecture) |
| Core Size | 32-Bit Dual-Core |
| Max Clock Speed | 64 MHz |
| Flash Memory | 1 MB (1M x 8) |
| Điện áp cung cấp | 3.3 V / 5 V |
| Connectivity | CANbus, FlexRay, LINbus, SPI, UART/USART |
| Peripherals | DMA, POR, PWM, WDT |
| Architecture | Dual Power Architecture (functional safety features on-chip) |
| Series | MPC56xx Qorivva |
| Nhiệt độ hoạt động | -40C to +125C |
| Hộp | 100-LQFP (14 x 14 mm) |
| Kiểu lắp đặt | Surface Mount |
| Grade | Automotive |
| Part Status | Active |
Hướng dẫn cấu hình chân SPC5643LFF2MLL6 100-lqfp (14 x 14 mm)
Cấu hình chân cho SPC5643LFF2MLL6 (100-lqfp (14 x 14 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho SPC5643LFF2MLL6.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SPC5643LFF2MLL6 phù hợp cho 6 Áp dụngs: Automotive Body Control Module, Automotive Gateway ECU, Industrial Control Systems, Chassis and Safety-Oriented Control Units, Telematics and Fleet Communication Nodes, Powertrain Auxiliary Control Units.
Automotive Body Control Module
The SPC5643LFF2MLL6 fits body control modules (BCM) because it combines dual e200z4 cores at 64 MHz with CAN and LIN controllers on a single die, allowing one processor to run the main body application and the diagnostics stack concurrently. The 1 MB flash accommodates full BCM firmware plus calibration tables, while the -40 C to +125 C automotive-grade rating survives cabin and engine-bay-adjacent environments. Its Dual Power Architecture supports safety-relevant load-disconnect and lighting functions with fewer external monitoring components. Typical designs run the LIN network for door and seat nodes off one LIN channel and the vehicle CAN backbone off another, with the 100-LQFP 14 x 14 mm footprint fitting cost-sensitive BCM PCBs. Peripheral PWM outputs directly drive lamp loads and motor H-bridges through external drivers, and the watchdog plus POR peripherals satisfy basic failure-detection requirements.
Được đề xuất
Automotive Gateway ECU
Gateway ECUs that bridge CAN, LIN, and FlexRay domains are a natural fit for the SPC5643LFF2MLL6, since it is one of the few 100-LQFP MCUs integrating all three network controllers on-chip. The dual e200z4 cores at 64 MHz partition routing/protocol handling from application logic, and DMA offloads message-buffer transfers to keep latency predictable. The 1 MB flash holds routing tables, multiple protocol stacks, and OTA-ready bootloaders with room to spare. With 3.3 V and 5 V supply domains, it interfaces directly to both legacy 5 V transceivers and modern 3.3 V PHYs without level shifting on many pins. Designers should reserve SRAM headroom for FlexRay message buffers and use the WDT plus the Dual Power Architecture monitors to meet gateway availability targets in the -40 C to +125 C automotive temperature range.
Được đề xuất
Industrial Control Systems
In industrial control, the SPC5643LFF2MLL6 offers an automotive-hardened 32-bit Power Architecture option for PLC I/O modules, motor-control heads, and rugged field controllers. Its -40 C to +125 C rating exceeds typical industrial requirements, providing margin in sealed enclosures, and the dual-core e200z4 at 64 MHz runs control loops alongside communication stacks. CANbus and UART/USART interfaces connect to drives and sensors, while PWM outputs and DMA support deterministic actuator control. The 5 V supply domain simplifies interfacing with legacy industrial 5 V logic and analog front ends, and the 1 MB flash supports protocol converters and parameter stores. The 100-LQFP 14 x 14 mm package hand-solders and reflows reliably on standard industrial PCB processes, and the WDT plus POR peripherals provide the watchdog and brownout behavior expected in continuously operating factory equipment.
Được đề xuất
Chassis and Safety-Oriented Control Units
For chassis functions such as suspension, steering-assist support nodes, and brake-related supervisory units, the SPC5643LFF2MLL6's Dual Power Architecture is the decisive feature: key functional safety mechanisms are integrated on a single chip, reducing the external safety circuit count and simplifying safety analyses. The dual e200z4 cores at 64 MHz can implement a processing path plus checking logic, and the FlexRay controller supports deterministic, fault-tolerant chassis network timing that plain CAN cannot guarantee. The 1 MB flash hosts the control algorithm plus diagnostic and end-of-line calibration code, while the -40 C to +125 C automotive grade covers wheel-arch and underhood mounting positions. Designers should follow NXP's MPC5643L safety documentation when architecting redundant sensing inputs and use the PWM and WDT peripherals for actuator supervision.
Được đề xuất
Telematics and Fleet Communication Nodes
Telematics boxes and fleet-management controllers benefit from the SPC5643LFF2MLL6's breadth of communication interfaces: CAN and LIN connect to the vehicle bus for data acquisition, while UART/USART links to cellular modems and GNSS receivers. The dual e200z4 cores at 64 MHz separate protocol preprocessing from application logic, and DMA-driven UART transfers keep modem streaming efficient. The 3.3 V supply matches modern modem module I/O directly, reducing level-shifting circuitry on the telematics PCB. The 1 MB flash stores agent firmware, buffering strategies, and device certificates, and the 100-LQFP 14 x 14 mm package keeps board area compact for DIN-rail or behind-dash installations. Operating across -40 C to +125 C, the MCU tolerates both cold-soak vehicle starts and solar-loaded enclosures without derating its 64 MHz clock.
Được đề xuất
Powertrain Auxiliary Control Units
Auxiliary powertrain ECUs - fuel-pump controllers, cooling-fan modules, and thermal-management units - are well served by the SPC5643LFF2MLL6. The -40 C to +125 C automotive grade covers engine-compartment mounting, and the 5 V supply domain interfaces with ratiometric sensors and legacy powertrain transceivers. Dual e200z4 cores at 64 MHz execute the control algorithm on one core while running diagnostics and CAN/LIN reporting on the other, and PWM peripherals drive MOSFET pre-drivers for pump and fan motors. The Dual Power Architecture supports the fail-safe behaviors these modules require, such as controlled shutdown on fault detection, with fewer external supervisory ICs. The 1 MB flash is ample for adaptive control strategies plus end-of-line calibration tables, and the 100-LQFP footprint suits the compact, thermally dissipative layouts typical of auxiliary powertrain boards.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SPC5643LFF2MLL6 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SPC5643LFF2MLQ1 | SPC5606BF1VLU6R | SPC5602BF2MLL6 | SPC5516GBMLQ66 |
|---|---|---|---|---|---|
| Package | 100-LQFP (14 x 14 mm) | 100-LQFP (14 x 14 mm) - same | 100-LQFP - same class | 100-LQFP (MLL6) - same | 100-LQFP - same class |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core / Clock | e200z4 dual-core, 64 MHz | e200z4 dual-core, 64 MHz | e200z3-family SPC560B core | SPC560B core | e200z0/z1-class, 66 MHz |
Bảo phân biệt quan trọng
- On-chip FlexRay controller (vsSPC5606BF1VLU6R)
- Dual Power Architecture functional-safety integration (vsSPC5602BF2MLL6)
- Dual-core e200z4 at 64 MHz with 1 MB flash (vsSPC5516GBMLQ66)
Ghi chú thiết kế
The SPC5643LFF2MLL6 uses 3.3 V and 5 V supply domains. Verify the internal regulator (if used) versus external regulator supply scheme early, per the MPC5643L power architecture section of the NXP datasheet, because the Dual Power Architecture assigns safety monitors to specific domains. Decouple each supply pin pair with 100 nF ceramics placed within 2 mm of the pin, plus bulk 10 uF per domain. Ensure the 5 V rail powers the flash/VDD domain per datasheet recommendations before code execution begins.
The 100-LQFP (14 x 14 mm) package has 0.5 mm pitch leads - use NSMD pads and solder-mask-defined avoidance of bridging on the CAN/FlexRay transceiver trace exits. Route FlexRay differential pairs as 100-ohm controlled impedance and keep them away from the crystal and switching regulator. Place the 8-40 MHz reference crystal (per NXP clocking options) close to the EXTAL/XTAL pins with ground guard. Allocate one full ground plane; do not split it under the MCU.
Three frequent mistakes with MPC5643L designs: (1) assuming all 100 pins are GPIO - many pads are multiplexed and some functions are mutually exclusive, so confirm with the signal-multiplexing tables in the NXP datasheet; (2) omitting the boot configuration strapping, which leaves the device booting from the wrong memory window; (3) under-budgeting SRAM for FlexRay message buffers, causing runtime allocation failure. Also verify the -40 C to +125 C rating of every companion part, not just the MCU.
Thông tin tuân thủ
Verified data confirms automotive-grade classification and active status but did not include explicit RoHS/REACH/halogen declarations for this ordering code. Obtain the certificate of conformance from nxp.com/part/SPC5643LFF2MLL6.