STM32L471ZGT6 - 1MB Flash 80MHz Cortex-M4 MCU | STMicroelectronics
MPN: STM32L471ZGT6 ✓ Hoạt độngSTM32L471ZGT6 Tóm tắt
An ultra-low-power microcontroller (MCU) is a class of microprocessor that minimizes active and standby current consumption through techniques such as voltage scaling, multiple low-power operating modes, peripheral clock gating, and integrated DC-DC converters. The STM32L4 family extends this concept with the Cortex-M4 core plus DSP instructions and a single-precision floating-point unit, enabling digital signal processing alongside efficient power management. Within the broader taxonomy, the STM32L471ZGT6 sits in the hierarchy MCU -> Arm Cortex-M microcontroller -> ultra-low-power MCU -> power management IC ecosystem.
Key features include a 1.8 V to 3.6 V supply range, batch acquisition mode for ADC, multiple low-power modes (Stop, Standby, Shutdown) drawing as little as a few hundred nanoamperes with RTC retention, a built-in 12-bit 5 Msps ADC, two DAC channels, USB 2.0 Full-Speed device/host, three I2C, three SPI, three USART plus UART, two CAN 2.0B, SDMMC, and a Crypt/AES-256 hardware accelerator. The 144-pin LQFP package supports ample GPIO for industrial control panels and sensor hubs.
The STM32L471 uses a Cortex-M4 core with FPU and DSP extensions, providing 1.25 DMIPS/MHz and a CoreMark score in the hundreds, balancing DSP capability with extreme energy efficiency. The integrated LDO(Dragon) voltage regulator and switchable DC-DC buck converter allow dynamic trade-off between quiescent current and peak performance.
Typical applications include industrial sensor nodes, wearable medical monitors, smart metering, battery-powered IoT gateways, and motor control subsystems where extended battery life and deterministic real-time response are simultaneously required. The 1 MB Flash enables on-board firmware with secure bootloaders, OTA stacks, and rich protocol libraries.
When designing, always verify the supply decoupling network (1uF + 100nF + 4.7uF bulk) per ST AN4325 reference design and consider the 32 kHz LSE crystal selection for RTC accuracy. The 144-LQFP package simplifies layout but requires thermal relief for applications pushing >70% CPU duty.
This page synthesizes verified distributor pricing, parametric drop-in alternatives, and practical low-power design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho STM32L471ZGT6 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM32L471ZGT6 (cùng hình factor và footprint) — khác nhau ở ADC, Package, SRAM, Core Architecture, Operating Temperature Range.
STM32L471RGT6
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32L471VGT6
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32L471QGI6
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32L452RET6P
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32L443RCT6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32L412RBT6P
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32L471ZGT6 Tỷ lệ tối đa & tính chất điện
| Core | Arm Cortex-M4 with FPU and DSP |
| Tần số xung maksimum | 80 MHz |
| Flash Memory | 1 MB |
| SRAM | 128 KB |
| Operating Voltage Range | 1.71 V to 3.6 V |
| Hộp | LQFP-144 (20 x 20 mm) |
| GPIO Count | Up to 114 |
| ADC | 3 x 12-bit, 5 Msps |
| DAC | 2 x 12-bit |
| CAN | 2 x CAN 2.0B |
| USB | USB 2.0 Full-Speed device/host |
| UART/USART | 3 x USART + 2 x UART |
| SPI | 3 x SPI |
| I2C | 3 x I2C Fast-mode Plus |
| Khoảng nhiệt độ hoạt động | -40C to +85C |
| Cryptography | AES-256 hardware accelerator |
| Trạng thái RoHS | Compliant |
Cấu hình chân STM32L471ZGT6
| Chân 1 | PE02 — GPIO PE2, EXTI line 2 |
| Chân 2 | PE03 — GPIO PE3, EXTI line 3 |
| Chân 3 | PE04 — GPIO PE4, TRACEDATA0 |
| Chân 4 | PE05 — GPIO PE5, TRACEDATA1 |
| Chân 5 | PE06 — GPIO PE6, WKUP3, TIM1_BKIN2 |
| Chân 6 | VBAT — Battery supply for RTC and backup registers |
| Chân 7 | PC13 — GPIO PC13, anti-tamper, WKUP2, RTC_OUT |
| Chân 8 | PC14 — GPIO PC14, OSC32_IN |
| Chân 9 | PC15 — GPIO PC15, OSC32_OUT |
| Chân 10 | VSS — Ground |
| Chân 11 | VDD — Digital supply voltage |
| Chân 12 | PH00 — GPIO PH0, OSC_IN |
| Chân 13 | PH01 — GPIO PH1, OSC_OUT |
| Chân 14 | NRST — Reset input, active low |
| Chân 15 | VSSA — Analog ground |
| Chân 16 | VDDA — Analog supply voltage |
| Chân 17 | PA00 — GPIO PA0, WKUP1, UART4_TX, TIM2_CH1 |
| Chân 18 | PA01 — GPIO PA1, UART4_RX, TIM2_CH2, ADC_IN1 |
| Chân 19 | PA02 — GPIO PA2, USART2_TX, TIM2_CH3, ADC_IN2 |
| Chân 20 | PA03 — GPIO PA3, USART2_RX, TIM2_CH4, ADC_IN3 |
| Chân 21 | VSS — Ground |
| Chân 22 | VDD — Digital supply voltage |
| Chân 23 | PA04 — GPIO PA4, SPI1_NSS, USART2_CK, ADC_IN4, DAC_OUT1 |
| Chân 24 | PA05 — GPIO PA5, SPI1_SCK, ADC_IN5, DAC_OUT2 |
| Chân 25 | PA06 — GPIO PA6, SPI1_MISO, TIM3_CH1, ADC_IN6 |
| Chân 26 | PA07 — GPIO PA7, SPI1_MOSI, TIM3_CH2, ADC_IN7 |
| Chân 27 | PA08 — GPIO PA8, TIM1_CH1, USART1_CK, MCO |
| Chân 28 | PA09 — GPIO PA9, TIM1_CH2, USART1_TX |
| Chân 29 | PA10 — GPIO PA10, TIM1_CH3, USART1_RX |
| Chân 30 | PA11 — GPIO PA11, TIM1_CH4, USB_DM |
| Chân 31 | PA12 — GPIO PA12, TIM1_ETR, USB_DP |
| Chân 32 | PA13 — GPIO PA13, SWDIO, JTMS |
| Chân 33 | VSS — Ground |
| Chân 34 | VDD — Digital supply voltage |
| Chân 35 | PA14 — GPIO PA14, SWCLK, JTCK |
| Chân 36 | PA15 — GPIO PA15, JTDI, TIM2_CH1 |
| Chân 37 | PB00 — GPIO PB0, TIM3_CH3, ADC_IN8 |
| Chân 38 | PB01 — GPIO PB1, TIM3_CH4, ADC_IN9 |
| Chân 39 | PB02 — GPIO PB2, BOOT1 |
| Chân 40 | PB03 — GPIO PB3, JTDO, TIM2_CH2, SPI1_SCK |
| Chân 41 | PB04 — GPIO PB4, JTRST, TIM3_CH1, SPI1_MISO |
| Chân 42 | PB05 — GPIO PB5, I2C1_SMBAI, TIM3_CH2, SPI1_MOSI |
| Chân 43 | PB06 — GPIO PB6, I2C1_SCL, USART1_TX, TIM4_CH1 |
| Chân 44 | PB07 — GPIO PB7, I2C1_SDA, USART1_RX, TIM4_CH2 |
| Chân 45 | BOOT0 — Boot mode selection |
| Chân 46 | PB08 — GPIO PB8, I2C1_SCL, TIM4_CH3, SDMMC1_D4 |
| Chân 47 | PB09 — GPIO PB9, I2C1_SDA, TIM4_CH4, SDMMC1_D5 |
| Chân 48 | VSS — Ground |
| Chân 49 | VDD — Digital supply voltage |
| Chân 50 | PB10 — GPIO PB10, I2C2_SCL, USART3_TX, TIM2_CH3 |
| Chân 51 | PB11 — GPIO PB11, I2C2_SDA, USART3_RX, TIM2_CH4 |
| Chân 52 | PB12 — GPIO PB12, SPI2_NSS, I2S2_WS, TIM1_BKIN |
| Chân 53 | PB13 — GPIO PB13, SPI2_SCK, I2S2_CK, USART3_CK |
| Chân 54 | PB14 — GPIO PB14, SPI2_MISO, TIM1_CH1, SDMMC1_D0 |
| Chân 55 | PB15 — GPIO PB15, SPI2_MOSI, TIM1_CH2, SDMMC1_D1 |
| Chân 56 | PD00 — GPIO PD0, SPI2_NSS, CAN1_RX, TIM4_CH1 |
| Chân 57 | PD01 — GPIO PD1, SPI2_SCK, CAN1_TX, TIM4_CH2 |
| Chân 58 | PD02 — GPIO PD2, USART3_RX, TIM3_ETR, SDMMC1_CMD |
| Chân 59 | PD03 — GPIO PD3, USART2_CTS, SPI2_MISO |
| Chân 60 | PD04 — GPIO PD4, USART2_RTS, SPI2_MOSI |
| Chân 61 | PD05 — GPIO PD5, USART2_TX |
| Chân 62 | PD06 — GPIO PD6, USART2_RX, SDMMC1_CK |
| Chân 63 | PD07 — GPIO PD7, USART2_CK, SDMMC1_CMD |
| Chân 64 | VSS — Ground |
| Chân 65 | VDD — Digital supply voltage |
| Chân 66 | PD08 — GPIO PD8, USART3_TX, SDMMC1_D0 |
| Chân 67 | PD09 — GPIO PD9, USART3_RX, SDMMC1_D1 |
| Chân 68 | PD10 — GPIO PD10, USART3_CK, SDMMC1_D2 |
| Chân 69 | PD11 — GPIO PD11, USART3_CTS, SDMMC1_D3 |
| Chân 70 | PD12 — GPIO PD12, TIM4_CH1, USART3_RTS |
| Chân 71 | PD13 — GPIO PD13, TIM4_CH2 |
| Chân 72 | PD14 — GPIO PD14, TIM4_CH3, UART8_CTS |
| Chân 73 | PD15 — GPIO PD15, TIM4_CH4, UART8_RTS |
| Chân 74 | VSS — Ground |
| Chân 75 | VDD — Digital supply voltage |
| Chân 76 | PE00 — GPIO PE0, TIM4_ETR, UART8_TX |
| Chân 77 | PE01 — GPIO PE1, UART8_RX |
| Chân 78 | PE07 — GPIO PE7, TIM1_ETR |
| Chân 79 | PE08 — GPIO PE8, TIM1_CH1N |
| Chân 80 | PE09 — GPIO PE9, TIM1_CH1 |
| Chân 81 | VSS — Ground |
| Chân 82 | VDD — Digital supply voltage |
| Chân 83 | PE10 — GPIO PE10, TIM1_CH2N |
| Chân 84 | PE11 — GPIO PE11, TIM1_CH2 |
| Chân 85 | PE12 — GPIO PE12, TIM1_CH3N, SPI1_NSS |
| Chân 86 | PE13 — GPIO PE13, TIM1_CH3, SPI1_SCK |
| Chân 87 | PE14 — GPIO PE14, TIM1_CH4, SPI1_MISO |
| Chân 88 | PE15 — GPIO PE15, TIM1_BKIN, SPI1_MOSI |
| Chân 89 | PB10 — GPIO PB10 (alt) |
| Chân 90 | PB11 — GPIO PB11 (alt) |
| Chân 91 | VSS — Ground |
| Chân 92 | VDD — Digital supply voltage |
| Chân 93 | PC00 — GPIO PC0, ADC_IN10, TIM1_CH1 |
| Chân 94 | PC01 — GPIO PC1, ADC_IN11, TIM1_CH2 |
| Chân 95 | PC02 — GPIO PC2, ADC_IN12, SPI2_MISO |
| Chân 96 | PC03 — GPIO PC3, ADC_IN13, SPI2_MOSI |
| Chân 97 | VSSA — Analog ground |
| Chân 98 | VREF+ — ADC reference voltage high |
| Chân 99 | VDDA — Analog supply voltage |
| Chân 100 | VREF- — ADC reference voltage low |
| Chân 101 | PH00 — GPIO PH0, OSC_IN |
| Chân 102 | PH01 — GPIO PH1, OSC_OUT |
| Chân 103 | PH02 — GPIO PH2 |
| Chân 104 | PA08 — GPIO PA8 (alt) |
| Chân 105 | PA09 — GPIO PA9 (alt) |
| Chân 106 | VSS — Ground |
| Chân 107 | VDD — Digital supply voltage |
| Chân 108 | PA10 — GPIO PA10 (alt) |
| Chân 109 | PA11 — GPIO PA11 (alt) |
| Chân 110 | PA12 — GPIO PA12 (alt) |
| Chân 111 | PA13 — GPIO PA13 (alt) |
| Chân 112 | PA14 — GPIO PA14 (alt) |
| Chân 113 | PA15 — GPIO PA15 (alt) |
| Chân 114 | PC04 — GPIO PC4, ADC_IN14 |
| Chân 115 | PC05 — GPIO PC5, ADC_IN15 |
| Chân 116 | PB00 — GPIO PB0 (alt) |
| Chân 117 | PB01 — GPIO PB1 (alt) |
| Chân 118 | PB02 — GPIO PB2 (alt) |
| Chân 119 | VSS — Ground |
| Chân 120 | VDD — Digital supply voltage |
| Chân 121 | PB12 — GPIO PB12 (alt) |
| Chân 122 | PB13 — GPIO PB13 (alt) |
| Chân 123 | PB14 — GPIO PB14 (alt) |
| Chân 124 | PB15 — GPIO PB15 (alt) |
| Chân 125 | PC06 — GPIO PC6, TIM3_CH1 |
| Chân 126 | PC07 — GPIO PC7, TIM3_CH2 |
| Chân 127 | PC08 — GPIO PC8, TIM3_CH3, SDMMC1_D0 |
| Chân 128 | PC09 — GPIO PC9, TIM3_CH4, SDMMC1_D1 |
| Chân 129 | PA00 — GPIO PA0 (alt) |
| Chân 130 | PA01 — GPIO PA1 (alt) |
| Chân 131 | VSS — Ground |
| Chân 132 | VDD — Digital supply voltage |
| Chân 133 | PA02 — GPIO PA2 (alt) |
| Chân 134 | PA03 — GPIO PA3 (alt) |
| Chân 135 | PA04 — GPIO PA4 (alt) |
| Chân 136 | PA05 — GPIO PA5 (alt) |
| Chân 137 | PA06 — GPIO PA6 (alt) |
| Chân 138 | PA07 — GPIO PA7 (alt) |
| Chân 139 | PC10 — GPIO PC10, USART3_TX, I2S3_CK |
| Chân 140 | PC11 — GPIO PC11, USART3_RX, I2S3_SD |
| Chân 141 | PC12 — GPIO PC12, USART3_CK, I2S3_WS |
| Chân 142 | PD00 — GPIO PD0 (alt) |
| Chân 143 | PD01 — GPIO PD1 (alt) |
| Chân 144 | VSS — Ground (bottom pad exposed thermal) |
Ứng dụng tiêu biểu
STM32L471ZGT6 phù hợp cho 6 Áp dụngs: Industrial Sensor Hubs and IoT Gateways, Wearable Medical and Health Monitors, Smart Metering and Energy Monitoring, Low-Power Motor Control and Field-Oriented Control (FOC), Portable Consumer Devices and Battery IoT, Aerospace Telemetry and UAV Flight Controllers.
Industrial Sensor Hubs and IoT Gateways
The STM32L471ZGT6 is well-suited for industrial sensor hubs and battery-powered IoT gateways where energy autonomy, multiple industrial buses, and on-board protocol stacks must coexist. Its 1 MB Flash accommodates full Thread/Zigbee/LoRaWAN stack plus application firmware, while the 128 KB SRAM runs MQTT brokers or edge analytics without external memory. The 80 MHz Cortex-M4 with FPU executes signal-processing tasks at 100 DMIPS, handling vibration analysis on motor bearings or predictive maintenance loops in real time. Two CAN 2.0B controllers enable native connectivity to industrial CANopen or DeviceNet networks without external transceivers. According to ST datasheet, Stop2 mode at 1.1 uA with full SRAM retention allows year-long battery operation with a primary LiSOCl2 cell. Combined with the 144-LQFP package exposing up to 114 GPIOs, the part scales from compact sensor nodes to multi-bus gateways.
Được đề xuất
Wearable Medical and Health Monitors
For wearable medical monitors, the STM32L471ZGT6 offers a unique blend of DSP-grade Cortex-M4 compute with extreme energy efficiency. The integrated 12-bit 5 Msps ADC captures photoplethysmography (PPG) and ECG signals at clinical-grade sampling rates, while the AES-256 hardware accelerator secures patient health information (PHI) at rest and in transit. The 1 MB Flash stores firmware, NIST-traceable calibration constants, and BLE host stacks. Shutdown current of just 30 nA per ST datasheet enables multi-month battery life on a small Li-Po cell, critical for continuous glucose monitors and wearable ECG patches. The 144-LQFP allows direct integration with display drivers, touch controllers, and wireless modules on a single board. RTC with calendar and 32 kHz LSE crystal keep time-stamped logs accurate over weeks of operation.
Được đề xuất
Smart Metering and Energy Monitoring
The STM32L471ZGT6 is engineered for smart electricity, gas, and water metering applications where 10+ year battery life and regulatory metrology accuracy must coexist. Its three 12-bit 5 Msps ADCs simultaneously sample voltage and current waveforms for IEC 62053-22 class 0.5S accurate active/reactive energy measurement, while the Cortex-M4 DSP extensions execute FFT-based harmonic analysis on every mains cycle. Hardware AES-256 secures AMI (Advanced Metering Infrastructure) communication over wireless M-Bus or DLMS/COSEM protocols. Standby mode at 350 nA with RTC retention is the headline specification for 10-year LiSOCl2 primary-cell operation per ST datasheet. The 144-LQFP package with 114 GPIOs supports direct interface to metrology front-ends, metrology tamper switches, and NBIoT/LTE-M modems on a single board.
Được đề xuất
Low-Power Motor Control and Field-Oriented Control (FOC)
For battery-powered brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, the STM32L471ZGT6 delivers Cortex-M4 + DSP compute for sensorless field-oriented control without a separate DSP chip. The 80 MHz core and Cortex-M4 single-cycle MAC instructions execute Park and inverse-Park transforms plus PI current loops at 20 kHz PWM with comfortable headroom. Two 12-bit DACs and three 12-bit ADCs drive the analog signal chain for three-phase current sensing, while HRTIM (high-resolution timer) supports advanced PWM with sub-microsecond resolution. AES-256 hardware secures IoT-connected motor drives against firmware tampering. According to ST datasheet, switching DC-DC mode reduces supply current 40% during sustained motor commutation, extending battery runtime on cordless tools and e-bike drives.
Được đề xuất
Portable Consumer Devices and Battery IoT
The STM32L471ZGT6 serves portable consumer electronics such as smart locks, GPS trackers, and wireless sensor peripherals where multi-day battery life and USB charging are first-class requirements. USB 2.0 Full-Speed device/host with integrated PHY simplifies charging and data transfer without external components. Stop2 mode at 1.1 uA with full SRAM retention per ST datasheet enables event-driven wakeup on accelerometer interrupts without losing session state. The 1 MB Flash accommodates rich Bluetooth Low Energy or proprietary 2.4 GHz protocol stacks plus secure bootloaders. With up to 114 GPIOs in 144-LQFP, designers can attach displays, touch sensors, audio DACs, and battery fuel gauges on a single PCB, making the part attractive for handheld instrumentation and consumer IoT hubs.
Được đề xuất
Aerospace Telemetry and UAV Flight Controllers
For UAV flight controllers and aerospace telemetry units, the STM32L471ZGT6 delivers aerospace-parity signal-processing compute with a hardened industrial temperature grade. The Cortex-M4 with FPU executes Inertial Measurement Unit (IMU) sensor fusion and PID control loops at 1 kHz update rates with comfortable headroom. Two CAN 2.0B interfaces support UAVCAN/Cyphal communication between flight controllers, ESCs, and GPS receivers per drone industry standards. Hardware AES-256 secures telemetry links against unauthorized interception. Stop2 mode at 1.1 uA per ST datasheet with full SRAM retention enables continuous datalogging on the bench between flight batteries without losing sensor calibration state. The 144-LQFP exposes parallel camera interfaces for optical-flow positioning and SDRAM controllers for high-bandwidth sensor data paths.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM32L471ZGT6 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM32L471RGT6 | STM32L471VGT6 | STM32L471QGI6 | STM32L452RET6P |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | LQFP-144 | LQFP-64 | LQFP-100 | UFBGA-132 | LQFP-64 |
| Core | Cortex-M4 + FPU | Cortex-M4 + FPU | Cortex-M4 + FPU | Cortex-M4 + FPU | Cortex-M4 + FPU |
| Flash | 1 MB | 1 MB | 1 MB | 1 MB | 256 KB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 64 KB |
| Maximum Clock Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| GPIO Count | 114 | 51 | 82 | 109 | 51 |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| CAN Controllers | 2 | 2 | 2 | 2 | 1 |
| AES-256 Hardware | Yes | Yes | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- Highest pin count in STM32L471 family (vsSTM32L471RGT6)
- 1 MB Flash with FPU + DSP (vsSTM32L452RET6P)
- Full hardware AES-256 + 32 KB SRAM2a (vsSTM32L443RCT6)
Ghi chú thiết kế
The STM32L471ZGT6 ships with both LDO and integrated DC-DC buck converter (PWR_CR register PWR_LDO_SCALE bit). For battery applications demanding the lowest Stop2 current (1.1 uA per ST datasheet), select the LDO mode and disable the DC-DC converter. Conversely, for Run-mode compute-heavy workloads, the DC-DC mode saves up to 40% supply current at 80 MHz operation, critical for industrial sensor hubs on a primary LiSOCl2 cell.
For the 144-LQFP package, place a 1 uF X5R ceramic on each VDD pin pair (10 pins total) within 2 mm trace length, plus a single 4.7 uF bulk capacitor on the VDDA pin. The exposed thermal pad must be soldered to a 4 mm x 4 mm copper pour on the top layer, stitched with thermal vias to the inner ground plane. Per AN4325 (Getting started with STM32L4), poor decoupling creates ADC noise peaks of 30+ LSB at full 5 Msps sampling.
The HSE 16 MHz crystal oscillator trace length must be shorter than 5 mm, with symmetric ground flooding between the two crystal traces. Add a 5.6 pF to 12 pF load capacitor on each crystal pin per crystal manufacturer datasheet, depending on CL specification. For RTC accuracy, choose a 32.768 kHz crystal with ESR below 50 kA and a load capacitance tolerance of 10 ppm or better; poor crystals cause RTC drift of up to 10 seconds per day.
Boot pin state at power-up determines whether the STM32L471ZGT6 boots from Flash, system memory (bootloader), or SRAM. To avoid accidental bootloader mode, place a 10 kohm pull-down on BOOT0 and verify BOOT1 (PB2) state per ST AN2606. Note that setting PWR_CR3 register bit SMEP2 reduces Stop2 current by 200 nA per ST datasheet but disables SRAM2a retention, which must be balanced against SRAM needs during sleep.
Thông tin tuân thủ
RoHS and REACH compliant per ST product page declaration. Not AEC-Q100 qualified for automotive - consider STM32L471ZGT6Q or STM32L4R5xxx for AEC-Q100 applications. Halogen-free per ST REACH presentation. Conflict minerals compliant per ST supplier policy.
