TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments
MPN: TAS5261DKDR ✗ Cuối đờiTAS5261DKDR Tóm tắt
A class D power stage is a switching amplifier topology that controls current through the speaker output at high frequency. Compared with a linear audio amplifier, the switching approach reduces the power dissipated in the output devices and enables high output power with smaller magnetic components. In the wider power-management hierarchy, the TAS5261 belongs to the class D amplifier family, which falls under audio amplifier ICs and, more broadly, power management semiconductors.
Key characteristics include 315 W rated mono output power, a single-channel class D architecture, a 36-HSSOP package, and a bridged-load-tie speaker configuration. The HSSOP package uses a gull-wing surface-mount form factor and exposes a thermal pad for heat removal when the device is mounted according to the manufacturer's recommended land pattern. Its operating voltage, output-stage limits, thermal characteristics, and signal-interface timing should be confirmed against the specific version of the manufacturer datasheet before layout release.
Typical implementations include powered speakers, compact home-theater enclosures, soundbars, multimedia speaker systems, subwoofer amplifier modules, and industrial audio products driven by an external audio processor. Because the device is a power stage rather than a complete codec-equipped amplifier, upstream circuitry must supply the required digital audio stream and control signals. A properly designed LC output filter is required to remove high-frequency switching energy before the loudspeaker.
Layout is the dominant design consideration. Place the input, control, power, and output-network connections according to the datasheet reference layout, minimize loop area in high-current switching paths, and provide substantial copper area for thermal dissipation. Verify junction temperature at worst-case supply voltage, output power, and ambient temperature rather than relying on nominal board temperature alone.
This page adds application-focused implementation guidance, pin-compatible sourcing information, and a structured comparison of the documented operating characteristics. Use the manufacturer datasheet and reference layout as the controlling documents for production design, EMC tuning, and thermal validation.
Bộ thay thế dễ dàng lắp đặt cho TAS5261DKDR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TAS5261DKDRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TAS5261DKDR Tỷ lệ tối đa & tính chất điện
| Device Type | Mono class D digital amplifier power stage |
| Number of Channels | 1 channel |
| Rated Output Power | 315 W mono |
| Cấu hình đầu ra | Mono bridged-load-tie (BTL) |
| Power Stage Topology | Class D switching amplifier |
| Hộp | 36-HSSOP, gull-wing surface mount |
| Number of Terminals | 36 |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| Kiểu lắp đặt | Surface mount |
| Recommended Minimum Load Resistance | 8 ohm |
| Input Signal Type | Single input signal with differential output |
Hướng dẫn cấu hình chân TAS5261DKDR rectangular
Cấu hình chân cho TAS5261DKDR (rectangular gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TAS5261DKDR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TAS5261DKDR phù hợp cho 6 Áp dụngs: Powered Subwoofer Module, Compact Home-Theater Speaker, Multimedia Speaker System, Soundbar Subwoofer Amplifier, Professional Active Monitor, Industrial Audio Announcement System.
Powered Subwoofer Module
The TAS5261DKDR fits a high-output subwoofer module because it combines a 315 W mono BTL power stage with a digital audio input architecture. An upstream audio processor can provide the required data and control signals while the power stage drives a low-impedance driver. The main design constraint is thermal: the HSSOP exposed-pad region must be tied to a generous copper area with thermal vias, and continuous output must be checked at the minimum intended supply voltage.
Được đề xuất
Compact Home-Theater Speaker
A compact home-theater speaker can use the TAS5261DKDR as a high-efficiency mono power stage for a woofer or full-range driver. The 315 W rating provides substantial headroom for transient audio peaks, while class D switching reduces the heat that must be removed compared with a comparable linear output stage. Use the recommended differential output network and isolate the amplifier from speaker wiring noise with correctly sized and rated inductors.
Được đề xuất
Multimedia Speaker System
The TAS5261DKDR is appropriate for multimedia speaker systems that require high power in a small enclosure and accept a digital audio input. Its single-channel BTL architecture suits one driver per module and avoids a conventional series output capacitor in the recommended circuit. The design must include a low-noise digital audio source, correct I2C-style control signaling, an LC filter, and thermal validation under sustained music output.
Được đề xuất
Soundbar Subwoofer Amplifier
In a soundbar subwoofer amplifier, the TAS5261DKDR provides a compact way to drive a low-impedance driver from a digital audio bus. The 315 W mono rating supports high short-term audio peaks, but enclosure temperature and acoustic loading strongly affect sustainable output. Place the switching output network and loudspeaker connector in accordance with the reference layout to suppress EMI and maintain predictable acoustic output.
Được đề xuất
Professional Active Monitor
An active monitor or studio near-field speaker can use the TAS5261DKDR for a high-output woofer channel. The class D architecture improves conversion efficiency and reduces thermal burden, allowing substantial amplifier output from a relatively compact board. Because large monitor cabinets can retain heat, validate the amplifier at sustained full-power operation with the passive crossover and enclosure loaded rather than at no-load bench conditions.
Được đề xuất
Industrial Audio Announcement System
The TAS5261DKDR can drive a high-power announcement or public-address driver in a mono bridged configuration. The 315 W class D power stage suits ruggedized audio equipment where efficiency, output power, and thermal performance are priorities. The system integrator must verify the control interface, configure the manufacturer output filter, and confirm that the loudspeaker and wiring load match the device's documented operating conditions.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho TAS5261DKDR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TAS5261DKDRG4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 36-HSSOP | 36-HSSOP |
| Lifecycle Status | End-of-life | Active |
| Output Power | 315 W mono | 315 W mono |
| Channel Count | 1 channel | 1 channel |
| Amplifier Class | Class D | Class D |
| Output Configuration | Mono BTL differential output | Mono BTL differential output |
| Terminal Count | 36 | 36 |
Bảo phân biệt quan trọng
- Retains the high-power mono class D identity (vsTAS5261DKDRG4)
- Better lifecycle position for new production (vsTAS5261DKDRG4)
- Mechanical reuse for existing HSSOP layouts (vsTAS5261DKDRG4)
Ghi chú thiết kế
The 36-HSSOP exposed-pad region is the primary thermal path for this 315 W class D power stage. Implement the manufacturer-recommended copper area and via array, keep the output current paths compact, and avoid thermal cross-talk from surrounding regulators. Validate the highest expected ambient temperature while the speaker load is continuously driven, because dissipation depends on supply voltage, output power, and switching loss.
Follow the manufacturer reference layout for the digital input, control signals, supply connections, exposed pad, and output filter. Place input and control traces away from the high-current switching nodes, and minimize the loop area of decoupling connections. The gull-wing package provides accessible pins, but correct land geometry and pad assignment remain necessary for both electrical performance and repeatable assembly.
Class D output edges contain high-frequency energy, so use the recommended LC filter and keep the switching node copper as small as practical. Route the filtered loudspeaker output away from sensitive input and control nets, and use a solid ground reference. Validate radiated and conducted emissions with the speaker cable and enclosure installed because the external wiring can materially change the EMI result.
Do not treat the green-tape suffix as proof of functional interchangeability. TI notes that some TAS5261DKDRG4 datasheet entries required confirmation, and the original TAS5261DKDR is end-of-life. Before substituting, compare pin functions, digital-interface timing, supply limits, protection behavior, output-filter requirements, and thermal data for the exact ordering code.
Thông tin tuân thủ
The commercial-grade audio power stage is not presented as an automotive-qualified AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established for this ordering code and remain unknown.