TLV2374ID - 16V 3MHz Quad RRIO Op Amp | Texas Instruments
MPN: TLV2374ID ✓ Hoạt độngTLV2374ID Tóm tắt
An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals, buffer inputs, perform active filtering, and drive downstream circuits. The TLV2374 belongs to the voltage-feedback amplifier hierarchy within the broader operational-amplifier and analog-signal-chain category. Four independent amplifiers in one package can reduce board area and simplify routing when a system requires multiple sensing or signal-conditioning channels.
The TLV2374ID combines rail-to-rail input and output operation with a 550 uA per-channel supply-current rating. Its 3 MHz gain-bandwidth product provides more bandwidth than many micropower amplifiers and makes it suitable for moderate-speed filtering and signal amplification. The 16 V maximum supply rating supports conventional 5 V, 8.4 V, and 12 V analog rails used in industrial equipment. Rail-to-rail operation extends usable input and output range toward the supply limits, although output-headroom and load-current limits must still be respected.
The device is intended for low-power, general-purpose analog designs and is identified by Texas Instruments as a standard instrumentation amplifier-family op amp. Four channels in one package can implement matched gain stages, differential-to-single-ended signal conversion, active filters, or sensor-conditioning channels. The 3 MHz bandwidth and low 550 uA per-channel current create a useful operating point when a design needs faster response than ultra-low-power amplifiers but does not justify the power and cost of a high-performance amplifier.
Typical applications include battery-powered sensor interfaces, industrial transducers, portable measurement equipment, audio input stages, and low-frequency active filters. Its low channel current is valuable in systems where four continuously operating amplifiers could dominate the standby-power budget. Where a signal changes rapidly, verify the closed-loop bandwidth, output-swing behavior, settling time, and capacitive-load drive required by the application.
PCB design should preserve the compactness benefit of the quad package without compromising analog performance. Place each bypassing capacitor close to its corresponding supply pin, route high-impedance input nodes with short traces and minimal parasitic capacitance, and keep output paths away from switching nodes. Confirm stability with the actual source impedance, load, and feedback network because amplifier behavior can change when driving capacitive loads or operating near the supply rails.
This page combines manufacturer device information with package-level engineering guidance, application fit, comparison criteria, and drop-in replacement considerations. The TLV2374ID datasheet remains the controlling reference for the complete electrical characteristics, pin assignments, recommended operating conditions, and test conditions used in a production design.
Bộ thay thế dễ dàng lắp đặt cho TLV2374ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2374ID (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Number of Channels, Gain-Bandwidth Product, Package, Maximum Supply Voltage.
TLV2374IDR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV2374IDG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV2374ID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Maximum Supply Voltage | 16 V |
| Minimum Operating Supply Voltage | 2.7 V |
| Gain-Bandwidth Product | 3 MHz |
| Supply Current per Channel | 550 uA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TLV2374ID 14-pin soic
Cấu hình chân cho TLV2374ID (14-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TLV2374ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLV2374ID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Industrial Transducer Interface, Portable Measurement Equipment, Audio Input Conditioning, Active Filtering and Active Filters, Low-Voltage Control Systems.
Battery-Powered Sensor Conditioning
The TLV2374ID fits battery-powered sensor-conditioning designs that need four low-power analog channels without accepting the bandwidth limit of an ultra-low-power amplifier. Its 550 uA supply current per channel and 2.7 V minimum operating voltage help constrain battery drain, while the 3 MHz gain-bandwidth product provides useful margin for gain and filtering stages. Place the amplifier close to the sensor interface, use short input routes, and bypass the supply locally. Check the complete sensor excitation and output-swing requirements because low supply voltage and heavy loading can reduce usable output range even when rail-to-rail operation is specified.
Được đề xuất
Industrial Transducer Interface
The TLV2374ID is suitable for industrial transducer interfaces that require several gain or buffer channels around one sensor or control node. Its quad configuration allows up to four 16 V operational amplifiers in one 14-pin SOIC package, while 550 uA per channel supports lower-power instrumentation. The 3 MHz gain-bandwidth product is suitable for many temperature, pressure, position, and bridge-sensor conditioning paths. Validate excitation frequency, input impedance, offset accuracy, and output drive against the transducer, and isolate high-current switching nodes from the sensitive analog section.
Được đề xuất
Portable Measurement Equipment
The TLV2374ID supports compact handheld and portable measurement equipment where four amplifiers can provide input buffering, active filtering, level conversion, and output conditioning. A 2.7 V minimum supply supports energy-conscious designs, while 550 uA per channel avoids making amplifier bias current the dominant load. The 3 MHz bandwidth gives useful margin for filters with moderate corner frequencies, but the design must account for output headroom at low supply voltages. Use short feedback traces, solid grounding, and local supply bypassing to preserve accuracy and stability.
Được đề xuất
Audio Input Conditioning
The TLV2374ID can provide general-purpose preamplifier, buffer, and crossover stages for line-level or low-level audio signals. Rail-to-rail input and output operation is useful when the signal occupies a large portion of a low-voltage supply, and the 3 MHz gain-bandwidth product exceeds the bandwidth of many audio-band signals. The four-channel package supports stereo or multi-channel routing. Check input-noise density, distortion, output-current capability, and load stability because the device is a general-purpose instrumentation amplifier rather than a dedicated low-noise audio part.
Được đề xuất
Active Filtering and Active Filters
The TLV2374ID is appropriate for multiple active-filter channels in measurement and control systems because each amplifier provides a 3 MHz gain-bandwidth product within a 550 uA per-channel power budget. Four channels can implement low-pass, high-pass, or notch stages without requiring separate packages. Select feedback resistors and capacitors for the intended corner frequencies, keep the feedback loop compact, and confirm phase margin with the actual source and load impedances. Avoid placing sensitive filter nodes next to switching-regulator traces or high-impedance sensor connections.
Được đề xuất
Low-Voltage Control Systems
The TLV2374ID fits compact low-voltage control systems requiring multiple amplifiers for error amplifiers, comparators, current loops, and actuator-signal conditioning. Operation from 2.7 V supports reduced-energy electronics, while rail-to-rail input and output behavior helps utilize narrow supply ranges. The 3 MHz bandwidth is useful for control loops that are faster than audio-band applications. Review the complete control-loop stability, output-swing, capacitive-load, and slew-rate requirements in the manufacturer datasheet, and add decoupling close to the package pins.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLV2374ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TLV2374IDR | TLV2374IDG4 |
|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V | 16 V |
| Minimum Operating Supply Voltage | 2.7 V | 2.7 V | 2.7 V |
| Gain-Bandwidth Product | 3 MHz | 3 MHz | 3 MHz |
| Supply Current per Channel | 550 uA | 550 uA | 550 uA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Format | Tube ordering form | Tape and reel | Green-roHS-compliant ordering designation |
Bảo phân biệt quan trọng
- Four-channel integration in a 14-pin SOIC package (vsTLV2374IDR)
- Low-power operation with useful bandwidth (vsTLV2374IDR)
- Rail-to-rail signal-path capability (vsTLV2374IDG4)
Ghi chú thiết kế
Place the supply-bypass capacitor immediately adjacent to the amplifier supply pins and connect it to the ground plane through a short, low-inductance path. Keep the sensitive input and feedback nodes compact, and route them away from switching-node copper, motor-drive outputs, and high-current return paths. Because the TLV2374ID can operate from 2.7 V to 16 V, select a capacitor voltage rating with suitable margin and verify its effective behavior across the complete supply range.
Do not assume that rail-to-rail input and output operation eliminates all headroom or stability constraints. Output current, load capacitance, output impedance, gain, and the selected feedback network still affect usable voltage swing and loop stability. Check the TLV2374 electrical-characteristics tables for the exact load and supply conditions, and include an isolation resistor when driving a capacitive load or long PCB trace.
Use the manufacturer's 14-pin SOIC pin description when assigning signals, and maintain a consistent ground reference for all four channels. Separate each channel's input routing from the power pins where practical, and avoid sharing narrow copper paths between high-impedance sensor inputs and amplifier outputs. Verify the assembled board for unintended coupling, especially when a switching converter, relay, or display interface is located near the quad analog package.
Thông tin tuân thủ
Compliance status was not explicitly stated in the manufacturer product-page result or distributor snippets. The automotive-grade TLV2374-Q1 is a separate product family and must not be treated as qualification for the standard TLV2374ID.