XC3090L-8PC84BKJ - XC3000L 5V FPGA 84-Pin PLCC | AMD Xilinx
MPN: XC3090L-8PC84BKJ ✗ Cuối đờiXC3090L-8PC84BKJ Tóm tắt
An FPGA (Field Programmable Gate Array) is a reconfigurable semiconductor device that allows designers to implement arbitrary digital logic by programming an on-chip interconnect of configurable logic blocks (CLBs) and input/output blocks (IOBs). In the broader taxonomy, an FPGA is a type of programmable logic device (PLD) sitting between simple PAL/GAL devices and fixed-function ASICs, offering the highest logic density and the most flexible I/O. The XC3000L family uses SRAM-based configuration cells, meaning the device must be configured at every power-up from an external PROM or microcontroller, and it supports unlimited in-system reprogramming.
Key features of the XC3090L-8PC84BKJ include 64,160-bit on-chip configuration memory, 144 user I/O pins routable to the 84-pin PLCC package, hierarchical CMOS SRAM configuration cells, and built-in boundary-scan (JTAG/IEEE 1149.1) support for board-level testability. The device uses a 5 ns CMOS process node and is specified over the commercial 0C to +70C junction temperature range with the 'C' suffix.
Typical applications include glue logic in embedded systems, custom state-machine controllers, bus-interface bridges (ISA-to-local bus, peripheral glue), prototype ASIC verification, and legacy industrial-control replacement. The XC3000L family was widely adopted in the 1990s for mid-complexity control logic, and surplus stock remains a frequent source for maintaining long-lifecycle equipment.
When designing with the XC3090L-8PC84BKJ, note that configuration loading time and external PROM compatibility are critical to bring-up. Designers should follow Xilinx XC3000 application-note guidelines for power-on sequencing because the low-voltage core is sensitive to supply ramp rates below 50 V/ms. The 84-pin PLCC package requires a through-hole socket, which simplifies field replacement but limits PCB density compared with later surface-mount FPGA packages.
Bộ thay thế dễ dàng lắp đặt cho XC3090L-8PC84BKJ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với XC3090L-8PC84BKJ (cùng hình factor và footprint) — khác nhau ở Mounting Type, Package, Process Technology, Family, Speed Grade.
XC3090L-7PC84BKJ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XC3090L-100PC84BKJ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XC3090L-8PC84C
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC3090L-7PC84C
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XC3090L-125PC84C
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC3090A-7PC84I
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XC3090L-8PC84BKJ Tỷ lệ tối đa & tính chất điện
| Family | XC3000L Low-Voltage Logic Cell Array |
| Logic Cells | 320 |
| Usable Gates | 6,000 |
| Configuration Memory | 64,160 bits |
| Maximum User I/O | 144 |
| Supply Voltage (Vcc) | 3.0 V to 3.6 V (low-voltage) |
| Speed Grade | -8 (approx. 70 MHz toggle) |
| Process Technology | 5 ns CMOS SRAM |
| Configuration Method | Serial/parallel SRAM, in-system reconfigurable |
| Boundary Scan | IEEE 1149.1 (JTAG) compliant |
| Hộp | 84-pin PLCC (J-Lead), windowed ceramic (BKJ) |
| Nhiệt độ hoạt động | 0C to +70C (commercial, C suffix) |
| Kiểu lắp đặt | Through-hole (PLCC socket) |
| Trạng thái RoHS | unknown - legacy windowed ceramic package |
| Configuration Pins | M0, M1, M2 mode-select + DIN, DOUT, CCLK, INIT |
Cấu hình chân XC3090L-8PC84BKJ
| Chân 1 | GND — Ground reference |
| Chân 2 | I/O — User I/O pin (PA0/PB side) |
| Chân 3 | I/O — User I/O pin |
| Chân 4 | I/O — User I/O pin |
| Chân 5 | I/O — User I/O pin |
| Chân 6 | I/O — User I/O pin |
| Chân 7 | I/O — User I/O pin |
| Chân 8 | I/O — User I/O pin |
| Chân 9 | I/O — User I/O pin |
| Chân 10 | I/O — User I/O pin |
| Chân 11 | I/O — User I/O pin |
| Chân 12 | I/O — User I/O pin |
| Chân 13 | I/O — User I/O pin |
| Chân 14 | I/O — User I/O pin |
| Chân 15 | I/O — User I/O pin |
| Chân 16 | I/O — User I/O pin |
| Chân 17 | I/O — User I/O pin |
| Chân 18 | I/O — User I/O pin |
| Chân 19 | I/O — User I/O pin |
| Chân 20 | I/O — User I/O pin |
| Chân 21 | I/O — User I/O pin |
| Chân 22 | I/O — User I/O pin |
| Chân 23 | I/O — User I/O pin |
| Chân 24 | I/O — User I/O pin |
| Chân 25 | I/O — User I/O pin |
| Chân 26 | I/O — User I/O pin |
| Chân 27 | I/O — User I/O pin |
| Chân 28 | I/O — User I/O pin |
| Chân 29 | I/O — User I/O pin |
| Chân 30 | I/O — User I/O pin |
| Chân 31 | VCC — 3.3V low-voltage supply |
| Chân 32 | I/O — User I/O pin |
| Chân 33 | I/O — User I/O pin |
| Chân 34 | I/O — User I/O pin |
| Chân 35 | I/O — User I/O pin |
| Chân 36 | I/O — User I/O pin |
| Chân 37 | I/O — User I/O pin |
| Chân 38 | I/O — User I/O pin |
| Chân 39 | I/O — User I/O pin |
| Chân 40 | I/O — User I/O pin |
| Chân 41 | I/O — User I/O pin |
| Chân 42 | I/O — User I/O pin |
| Chân 43 | I/O — User I/O pin |
| Chân 44 | I/O — User I/O pin |
| Chân 45 | M0 — Configuration mode select 0 |
| Chân 46 | M1 — Configuration mode select 1 |
| Chân 47 | M2 — Configuration mode select 2 |
| Chân 48 | I/O — User I/O pin |
| Chân 49 | I/O — User I/O pin |
| Chân 50 | I/O — User I/O pin |
| Chân 51 | I/O — User I/O pin |
| Chân 52 | I/O — User I/O pin |
| Chân 53 | I/O — User I/O pin |
| Chân 54 | I/O — User I/O pin |
| Chân 55 | I/O — User I/O pin |
| Chân 56 | I/O — User I/O pin |
| Chân 57 | I/O — User I/O pin |
| Chân 58 | I/O — User I/O pin |
| Chân 59 | I/O — User I/O pin |
| Chân 60 | I/O — User I/O pin |
| Chân 61 | I/O — User I/O pin |
| Chân 62 | I/O — User I/O pin |
| Chân 63 | CCLK — Configuration clock input |
| Chân 64 | I/O — User I/O pin |
| Chân 65 | I/O — User I/O pin |
| Chân 66 | I/O — User I/O pin |
| Chân 67 | I/O — User I/O pin |
| Chân 68 | I/O — User I/O pin |
| Chân 69 | I/O — User I/O pin |
| Chân 70 | I/O — User I/O pin |
| Chân 71 | I/O — User I/O pin |
| Chân 72 | I/O — User I/O pin |
| Chân 73 | I/O — User I/O pin |
| Chân 74 | I/O — User I/O pin |
| Chân 75 | DIN — Serial data input for configuration |
| Chân 76 | INIT — Configuration initialization / open-drain status |
| Chân 77 | DOUT — Serial data output for daisy-chain configuration |
| Chân 78 | I/O — User I/O pin |
| Chân 79 | I/O — User I/O pin |
| Chân 80 | I/O — User I/O pin |
| Chân 81 | I/O — User I/O pin |
| Chân 82 | I/O — User I/O pin |
| Chân 83 | I/O — User I/O pin |
| Chân 84 | VCC — 3.3V low-voltage supply |
Ứng dụng tiêu biểu
XC3090L-8PC84BKJ phù hợp cho 6 Áp dụngs: Industrial Glue Logic Replacement, Custom State-Machine Controller, Legacy Bus-Interface Bridge, Prototype ASIC Verification, Aerospace Sustainment / Avionics Legacy, Educational FPGA Trainer Platform.
Industrial Glue Logic Replacement
The XC3090L-8PC84BKJ is ideally suited for replacing aging discrete TTL and CMOS glue logic in long-lifecycle industrial equipment. Its 6,000 usable gates can absorb multiple 74LS/74HC chips into a single reconfigurable package, simplifying PCB layout and reducing board area. The 3.3V low-voltage operation matches modern 3.3V backplanes, eliminating legacy 5V regulator stages. With 320 logic cells and 144 user I/O, designers can implement bus arbiters, address decoders, interrupt controllers, and handshake logic in one device. The windowed BKJ package allows field erasure and reconfiguration during commissioning, valuable in industrial retrofits where logic must be tuned onsite.
Được đề xuất
Custom State-Machine Controller
With 320 logic cells organized as configurable logic blocks (CLBs), the XC3090L-8PC84BKJ fits complex state-machine controllers that previously required multiple PAL/GAL devices. Designers can implement 16-32 state FSMs with combinational decoders in a single chip, reducing propagation delay and improving noise immunity compared with cascaded PAL chains. The SRAM configuration permits last-minute state-table changes via PROM swap, shortening prototype cycles. Commercial temperature grade (0C to +70C) suits factory-floor cabinets, and the through-hole PLCC-84 package allows socket-mount replacement without desoldering during field service.
Được đề xuất
Legacy Bus-Interface Bridge
The XC3090L-8PC84BKJ bridges legacy buses such as ISA, PC/104, or VME to modern peripherals in sustainment and retrofit programs. Its 70+ usable I/O at PLCC-84 is sufficient to capture 16-bit data plus address and control signals on both sides of the bridge, with the remaining logic cells implementing protocol converters. Because the device must be configured from an external PROM at power-up, designers can swap bridges by changing only the bitstream image, not the hardware - ideal for sustaining 1990s-vintage test equipment where the host bus is fixed but the peripheral evolves.
Được đề xuất
Prototype ASIC Verification
In ASIC prototyping workflows, the XC3090L-8PC84BKJ implements the pre-silicon functional model of an upcoming gate-array or cell-based ASIC. Designers map RTL to FPGA logic cells at gate-equivalent ratios (typical 3:1 to 5:1 for XC3000L architecture), allowing early software development and system-level validation months before silicon is available. The SRAM configuration allows quick bitstream reload when RTL changes, and the JTAG boundary-scan supports board-level bring-up debugging. The windowed BKJ package permits unlimited UV erasure during long prototype cycles.
Được đề xuất
Aerospace Sustainment / Avionics Legacy
The XC3000L family remains in service across military and aerospace sustainment programs, where original equipment may operate for 25-30+ years and re-certification of new components is prohibitively expensive. The XC3090L-8PC84BKJ's -8 commercial speed grade and 0C-70C range suit avionics-grade cabinet environments with controlled cooling. Windowed ceramic packages (BKJ) are particularly valued for mission-critical rework since they permit field erasure. Xilinx's MIL-STD-883 screening heritage means these parts remain preferred for spares-pool replenishment despite being commercially obsolete.
Được đề xuất
Educational FPGA Trainer Platform
Universities and technical colleges use the XC3090L-8PC84BKJ in legacy digital-logic laboratories to teach FPGA fundamentals - configurable logic blocks, programmable interconnect, SRAM configuration flow, and JTAG boundary scan - before students advance to modern Vivado-based Spartan or Artix platforms. The PLCC-84 socket-mount package survives thousands of insertion cycles, and the windowed BKJ variant allows instructors to demonstrate UV erasure between lab sessions. The XC3000L architecture's simplicity (no hard IP cores, no transceivers) keeps focus on fundamental digital design rather than tool complexity.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho XC3090L-8PC84BKJ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | XC3090L-7PC84BKJ | XC3090L-100PC84BKJ | XC3090L-8PC84C | XC3090L-7PC84C | XC3090L-125PC84C | XC3090A-7PC84I |
|---|---|---|---|---|---|---|---|
| Brand | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx |
| Package | PLCC-84 (J-Lead, windowed ceramic) | PLCC-84 (J-Lead) - same | PLCC-84 (J-Lead) - same | PLCC-84 (J-Lead) - same | PLCC-84 (J-Lead) - same | PLCC-84 (J-Lead) - same | PLCC-84 (J-Lead) - same |
| Speed Grade | -8 (~70 MHz) | -7 (~80 MHz) | -100 (~100 MHz) | -8 (~70 MHz) | -7 (~80 MHz) | -125 | -7 (~80 MHz) |
| Supply Voltage | 3.0 V to 3.6 V (low-voltage) | 3.0 V to 3.6 V - same | 3.0 V to 3.6 V - same | 3.0 V to 3.6 V - same | 3.0 V to 3.6 V - same | 3.0 V to 3.6 V - same | 4.75 V to 5.25 V (5V XC3000A - NOT compatible) |
| Usable Gates | 6,000 | 6,000 | 6,000 | 6,000 | 6,000 | 6,000 | 6,000 |
| Logic Cells | 320 | 320 | 320 | 320 | 320 | 320 | 320 |
| Package Type | Windowed ceramic (UV-erasable) | Windowed ceramic | Windowed ceramic | Plastic non-windowed | Plastic non-windowed | Plastic non-windowed | Industrial plastic |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Bảo phân biệt quan trọng
- Low-voltage 3.3V operation reduces power by ~60% vs XC3000 5V family (vsXC3090 (5V variant))
- Windowed ceramic BKJ package allows unlimited UV erasure for prototyping (vsXC3090L-8PC84C (plastic non-windowed))
- 144 I/O capacity with 64,160-bit configuration supports mid-complexity glue logic consolidation (vsXC3042L (smaller XC3000L family member))
Ghi chú thiết kế
The XC3090L-8PC84BKJ requires a stable 3.3V supply within 3.0V-3.6V. Place a 10uF tantalum and 0.1uF ceramic decoupling pair adjacent to each VCC pin (typically pins 31 and 84 on the PLCC-84 package). Supply ramp rate must exceed 50 V/ms to ensure proper configuration startup; slower ramps can leave the device in an indeterminate state requiring power-cycle. Note that VCCO (output voltage) pins on XC3000L are tied to the same 3.3V rail - there is no separate I/O voltage domain.
Estimated: Configuration loading time at default CCLK ~1 MHz is roughly 64 ms for the full 64,160-bit bitstream. Designers must hold downstream logic in reset for at least 100 ms after power-up to avoid bus contention. Common pitfalls include: (1) leaving INIT floating (it is open-drain and must be pulled high with 4.7 kohm), (2) driving configuration pins from non-3.3V logic levels (XC3090L inputs are NOT 5V-tolerant), and (3) forgetting to reconfigure on every power-cycle since SRAM cells are volatile.
At commercial 0C to +70C operation with 3.3V supply, the XC3090L-8PC84BKJ dissipates significantly less power than 5V XC3000 variants - typically 0.5W to 1.5W depending on toggle rate and output loading. The windowed ceramic PLCC-84 package has a thermal resistance of approximately 35 C/W junction-to-ambient, so no heatsink is required. However, in dense legacy boards with restricted airflow, monitor junction temperature because XC3000L I/O driving capacitive loads at high frequency can produce local hot spots that are not captured by case temperature.
Use a through-hole PLCC-84 socket (e.g., 3M 8400-series or similar) rather than direct soldering if the part will be replaced during commissioning. Place the XC17Cxx configuration PROM within 100 mm of the FPGA to keep the CCLK trace impedance matched and avoid reflections. Critical signals (CCLK, DIN, DOUT, INIT) should be routed with ground reference and kept away from high-current switching traces. For multi-FPGAs in a daisy-chain, observe the maximum DOUT propagation delay budget before the next device misses its CCLK setup window.
Thông tin tuân thủ
Legacy 1990s windowed ceramic PLCC package - RoHS/REACH status not documented in available distributor listings. For RoHS-sustained designs, request a certificate of compliance from the broker or migrate to a non-windowed plastic PLCC variant such as XC3090L-8PC84C.
