產品(44,000+)

STM32L443VCT6 - 80MHz Cortex-M4 256KB MCU | ST
STM32L443VCT6

STM32L443VCT6 - 80MHz Cortex-M4 256KB MCU | ST

STMicroelectronics STM32L443VCT6 is an ultra-low-power 32-bit microcontroller with an Arm Cortex-M4 core operating up to 80 MHz, 256 KB of Flash memory, 64 KB of SRAM, and a 100-LQFP 14 x 14 mm package. The device combines 100 DMIPS processing performance with USB full-speed, LCD, analog, audio, and AES-2 hardware features for compact low-power embedded systems. An ultra-low-power microcontroller is a semiconductor designed to perform control, measurement, and communication tasks while minimizing energy consumption. The STM32L4 series belongs to the Arm Cortex-M microcontroller hierarchy and combines a real-time processor core with embedded Flash, SRAM, analog converters, timers, communication peripherals, and low-power modes. This integration reduces the component count needed in battery-powered industrial, medical, consumer, and IoT equipment. The STM32L443VCT6 operates from a 1.71 V to 3.6 V supply and supports temperature ranges from -40 °C to 85 °C, 105 °C, or 125 °C, depending on the exact ordering variant. Its low-power behavior includes 200 nA consumption in VBAT mode for the real-time clock and 32 backup registers, plus an 8 nA shutdown mode with five wakeup pins. These figures support designs where standby current materially affects service intervals and battery life. The Arm Cortex-M4F architecture provides floating-point instructions alongside the MCU's 256 KB Flash and 64 KB SRAM. Integrated USB full-speed connectivity allows a compact device to exchange data with a host without an external USB transceiver. LCD support, analog functions, audio capability, and AES-2 acceleration make the device suitable for instrument panels, portable measurements, secure accessories, and connected low-power products. Typical applications include battery-powered health monitors, USB-connected data loggers, industrial sensor nodes, LCD control panels, secure access devices, and compact consumer instruments. In these systems, the STM32L443VCT6 can consolidate local control, data acquisition, encrypted communication, and human-interface functions while retaining multiple low-energy operating states. PCB implementation should preserve clean supply distribution, short analog-input routes, and appropriate decoupling around the device. The 100-LQFP package requires careful fanout and inspection, while USB routing, ground continuity, and exposed signal paths need to follow the layout constraints in the manufacturer datasheet. Validate power sequencing, clock configuration, firmware startup, and low-power wake behavior on the assembled board. This product page consolidates the manufacturer's core specifications, package information, application guidance, practical design notes, and qualified same-family alternatives into a design-focused reference. It also distinguishes exact electrical differences among drop-in candidates so engineers can assess replacement suitability without changing the PCB footprint.

詢價 聯絡我們
STM32L451CEU6 - 80MHz Cortex-M4 MCU 512KB Flash | STMicroelectronics
STM32L451CEU6

STM32L451CEU6 - 80MHz Cortex-M4 MCU 512KB Flash | STMicroelectronics

The STMicroelectronics STM32L451CEU6 is an ultra-low-power 32-bit ARM Cortex-M4 microcontroller with FPU operating at up to 80 MHz, packaged in a 48-pin UFQFPN (7x7 mm). It integrates 512 KB of Flash memory and 160 KB of SRAM, providing substantial headroom for embedded applications that combine an RTOS with rich peripheral stacks. An ultra-low-power microcontroller (MCU) is a class of 32-bit microcontroller optimized for battery-powered and energy-harvesting systems where average current draw over sleep-active duty cycles is the dominant design constraint. Within the broader taxonomy, the STM32L4 sits between general-purpose Cortex-M4 MCUs and the lower-power Cortex-M0+ families, occupying the ultra-low-power branch alongside the Cortex-M33 STM32L5 and Cortex-M0+ STM32L0. Its FPU and DSP extensions place it above M0+ parts in compute density, while its multi-domain power architecture (separate Core, peripheral, and memory voltage domains) places it above classical Cortex-M4 in energy efficiency. Key differentiating specifications include the 80 MHz Cortex-M4 core with single-precision FPU and DSP instructions, 1.71 V to 3.6 V operating supply range, five low-power modes (Sleep, Low-Power Sleep, Stop 0/1/2, Standby, Shutdown) with Shutdown current under 30 nA typical, and an integrated 12-bit ADC with hardware oversampling. The device also provides two DAC channels, three I2C, three SPI, one CAN 2.0B, one USB 2.0 Full-Speed device/host, and an integrated DFSDM digital filter for sigma-delta modulation. Architecturally, the STM32L451CEU6 uses ST's 90 nm ultra-low-leakage process with an adaptive voltage scaling loop that scales the core domain between 1.0 V and 1.2 V based on operating frequency. This allows RUN-mode current to track load and yields approximately 100 uA/MHz active efficiency. The 160 KB SRAM is split into multiple independent banks to allow retention-only sleep configurations that keep selected peripherals alive while the core domain is powered down. Typical applications include wearable health monitors, battery-powered sensor hubs, industrial 4-20 mA loop-powered transmitters, smart metering, BLE/Zigbee host controllers, and low-end audio processing using the on-board DFSDM. The 48-pin UFQFPN package is the right density point for designs needing CAN or USB plus a 12-bit analog front-end without paying for the larger 64-pin variants. When designing with this device, prioritize decoupling close to each VDD pin pair (one 100 nF X7R per domain plus one 4.7 uF bulk) and respect the UFQFPN exposed-pad solder process to keep junction temperature rise within datasheet limits. The Cortex-M4 FPU is single-precision only - use double-precision math in firmware will trap. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
STM32L451RCT6 - 80MHz Cortex-M4 MCU 256KB | STMicroelectronics
STM32L451RCT6

STM32L451RCT6 - 80MHz Cortex-M4 MCU 256KB | STMicroelectronics

The STMicroelectronics STM32L451RCT6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 processor with floating-point unit, operating up to 80 MHz, with 256 KB of Flash memory in a 64-pin LQFP package measuring 10 mm by 10 mm. It integrates DFSDM capability and is designed for compact embedded systems requiring efficient processing, analog signal acquisition and low-power operation. An ultra-low-power microcontroller is a semiconductor device optimized to complete control, sensing and communication tasks while minimizing energy consumption. The STM32L451 belongs to the STM32L4 low-power microcontroller family, combining an Arm Cortex-M4 RISC core with embedded Flash, SRAM, analog peripherals, digital interfaces and power-management functions. This hierarchy places the device between general-purpose application processors and simple fixed-function controllers. The device operates at up to 80 MHz and provides 256 KB of Flash for firmware and data storage. Its 32-bit architecture supports efficient handling of control loops, communications protocols, digital filtering and floating-point calculations. The integrated DFSDM feature is particularly useful for direct digital conversion of sigma-delta modulators and analog signals. The 64-LQFP package provides a relatively large lead pitch and facilitates assembly, inspection and hand rework compared with fine-pitch QFN packages. The STM32L451 device family is positioned for applications where energy efficiency and real-time control matter. Relevant peripheral combinations can support industrial sensing, low-power instrumentation, connected equipment, analog measurement and compact control systems. Its 80 MHz Cortex-M4 core provides substantially more processing headroom than low-speed microcontrollers while retaining the efficiency benefits of an embedded architecture. Typical uses include industrial sensor controllers, digital audio and analog measurement equipment, building automation modules, compact industrial gateways, battery-operated instruments and low-energy embedded control boards. The 64-pin LQFP format is especially convenient for prototypes and mixed-signal designs because it exposes more I/O than smaller packages and avoids difficult inspection of fine-pitch leads. Designers should plan the power tree around the operating mode, peripheral load and retention requirements because performance and current consumption are closely related. Decoupling should be placed close to the supply pins, unused inputs should be configured appropriately, and firmware should exercise the low-power modes when energy use is important. The DFSDM and analog circuitry also require careful grounding and signal-routing discipline to preserve measurement quality. This product page consolidates the verified device identity, package information, practical design guidance, application fit and strict drop-in alternatives. It also distinguishes exact same-footprint options from parts that require different packages, helping engineers shorten sourcing and redesign work before committing to a PCB change.

詢價 聯絡我們
STM32L451REI6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics
STM32L451REI6

STM32L451REI6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics

The STMicroelectronics STM32L451REI6 is an ultra-low-power 32-bit microcontroller built around the Arm Cortex-M4 processor with floating-point unit support and a maximum operating frequency of 80 MHz. It provides 512 KB of embedded Flash memory, 160 KB of SRAM, and analog, audio, and digital filter sigma-delta modulator support in a 64-UFBGA package measuring 5 x 5 mm. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and communication interfaces onto one component. The Cortex-M4 core gives the STM32L451 a compact architecture suited to real-time control, while the STM32L4 family emphasizes low-power operation. In the product hierarchy, this device is an MCU, an embedded processing component within the broader semiconductor category, and it bridges general-purpose embedded control with specialized analog and audio acquisition. Three characteristics distinguish the STM32L451REI6 for compact, low-power designs. Its 80 MHz Cortex-M4 core delivers high processing performance for control algorithms and protocol handling. The 512 KB Flash capacity supports larger embedded programs and data storage than entry-level Cortex-M devices. The integrated DFSDM block supports digital sigma-delta conversion applications, while the analog and audio feature set broadens the device's usefulness for sensor and signal-chain designs. The device belongs to STMicroelectronics' STM32L4 family, which combines a high-performance Arm Cortex-M4 core with ultra-low-power design goals and extensive peripheral integration. Its 160 KB SRAM provides working memory for data buffering, display or communications handling, and interrupt-driven acquisition. The 64-UFBGA land-grid array reduces PCB footprint compared with leaded packages and supports dense products with limited board area. Typical applications include low-power sensor nodes, industrial monitoring equipment, connected measurement instruments, low-power audio signal conditioning, battery-operated portable systems, and compact control boards. Its 80 MHz processing headroom allows digital filtering and system control to coexist with communication tasks, while the DFSDM capability can assist with delta-sigma front ends when appropriate analog support is also configured. When laying out the PCB, follow the manufacturer's land pattern, pad, and via recommendations for the 64-UFBGA package. Confirm the pin multiplexing, supply requirements, decoupling, clock configuration, and exposed-pad connection in the STM32L451xx datasheet before release. Firmware migration should be checked against peripheral differences because devices in the STM32L4 family may not share identical clock trees, analog blocks, or low-power feature sets. This page combines the manufacturer's device description with practical guidance on package handling, memory sizing, peripheral use, and substitution. It also provides parameter comparisons for nearby STMicroelectronics STM32L4 devices so engineers can identify a same-footprint option while checking flash, SRAM, temperature-range, and peripheral differences before committing to a drop-in replacement.

詢價 聯絡我們
STM32L451RET6 - Ultra-Low-Power Cortex-M4 MCU 512KB Flash | STMicroelectronics
STM32L451RET6

STM32L451RET6 - Ultra-Low-Power Cortex-M4 MCU 512KB Flash | STMicroelectronics

The STM32L451RET6 is an ultra-low-power 32-bit microcontroller from STMicroelectronics, based on the high-performance Arm® Cortex®-M4 32-bit RISC core with floating-point unit (FPU). It operates at a frequency of up to 80 MHz, delivering 100 DMIPS, and is designed for a wide range of battery-powered and energy-efficient applications. The device features 512 KB of Flash memory and 160 KB of SRAM, providing ample storage and execution space for complex firmware. It is housed in a 64-pin LQFP package (10x10 mm), making it suitable for space-constrained designs. A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory, and programmable input/output peripherals. The STM32L451RET6 belongs to the STM32L4 series, which is part of the broader STM32 family of 32-bit microcontrollers. This series is optimized for ultra-low-power consumption, making it ideal for IoT devices, wearables, and industrial sensors. The Cortex-M4 core with FPU enhances performance for digital signal processing (DSP) tasks, while the rich set of analog and digital peripherals enables versatile system integration. Key features of the STM32L451RET6 include a 12-bit ADC with 5 MSPS, two 12-bit DACs, an operational amplifier, a comparator, and a digital filter for sigma-delta modulators (DFSDM). It also supports multiple communication interfaces: I2C, SPI, USART, UART, LPUART, SAI, and CAN. The device integrates a real-time clock (RTC), several timers, and a true random number generator (TRNG). Its ultra-low-power modes, including Sleep, Low-power run, Low-power sleep, Stop 0/1/2, and Standby, allow designers to minimize energy consumption in battery-operated systems. From a technical perspective, the STM32L451RET6 is built on a 40 nm process technology, which contributes to its low power consumption. It operates from a 1.71 V to 3.6 V power supply, and its GPIOs are 5V-tolerant, simplifying interfacing with legacy logic. The device includes a memory protection unit (MPU) and a hardware cryptographic accelerator (AES) for secure applications. The flexible power management with multiple voltage scaling options (Range 1, 2, and 3) allows the core to run at lower voltages to save power when performance is not critical. Typical applications for the STM32L451RET6 include smart meters, medical devices, industrial sensors, portable instrumentation, and IoT edge nodes. Its combination of low power, high performance, and rich analog peripherals makes it a preferred choice for applications requiring long battery life and precise analog measurements. For example, in a smart meter, the MCU can handle metering calculations, communication protocols, and display control while consuming minimal power in standby mode. When designing with this MCU, it is essential to pay attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 4.7 uF capacitor at the main power input. Additionally, the VDDA pin must be connected to a clean analog supply, and the VREF+ pin should be decoupled with a 1 uF capacitor for accurate ADC conversions. Proper layout of the crystal oscillator (if used) is critical for reliable clock operation.

詢價 聯絡我們
STM32L451VCI6 - 80MHz 256KB MCU for IoT | STMicroelectronics
STM32L451VCI6

STM32L451VCI6 - 80MHz 256KB MCU for IoT | STMicroelectronics

STMicroelectronics STM32L451VCI6 is an ultra-low-power 32-bit Arm Cortex-M4 microcontroller with FPU, operating up to 80 MHz, with 256 KB of Flash memory, in a 100-UFBGA 7 x 7 mm package. The STM32L4 family combines a high-performance Cortex-M4 processor with up to 100 DMIPS and a strong focus on energy-efficient embedded control. An ultra-low-power microcontroller is a semiconductor designed to perform computing and control tasks while minimizing energy consumption during active operation, sleep, and standby periods. The STM32L4 family belongs to the embedded MCU hierarchy, combining an Arm Cortex-M4 processor core, embedded Flash, SRAM, analog peripherals, communications interfaces, and low-power management in one device. This integration reduces component count and supports compact, energy-conscious embedded systems. Key device attributes include an Arm Cortex-M4 core with FPU, 80 MHz maximum operating frequency, 256 KB of embedded Flash, and a 100-UFBGA package measuring 7 x 7 mm. The family-level datasheet identifies performance up to 100 DMIPS and device options up to 512 KB of Flash and 160 KB of SRAM. Analog and audio capabilities make the STM32L451 series relevant to low-power sensing, industrial control, connected equipment, and embedded audio designs. The Cortex-M4 architecture provides 32-bit processing and a floating-point unit for control loops and signal-processing tasks. Its 80 MHz operating rate gives applications more compute headroom than lower-frequency Cortex-M devices while the ultra-low-power design target supports battery-operated and duty-cycled products. The exact SRAM, peripheral complement, voltage range, and power figures for this ordering code require confirmation from the manufacturer ordering information. Typical applications include connected sensor nodes, industrial monitoring equipment, low-power instrumentation, digital audio control, and compact embedded control systems. Designers can use the Cortex-M4 core for protocol handling, real-time control, and peripheral coordination, while the family’s analog and audio features support mixed-signal products that require both computation and signal acquisition. A critical design consideration is package-level planning. The STM32L451VCI6 uses a compact 100-UFBGA footprint with fine-pitch balls, requiring a PCB with suitable solder mask, pad, and assembly-process capability. Designers should also verify the exact GPIO assignments, power pins, decoupling requirements, and peripheral multiplexing against the manufacturer datasheet before schematic capture or PCB release.

詢價 聯絡我們
STM32L451VCT6 - 80MHz Cortex-M4 MCU, 256KB Flash | STMicroelectronics
STM32L451VCT6

STM32L451VCT6 - 80MHz Cortex-M4 MCU, 256KB Flash | STMicroelectronics

The STMicroelectronics STM32L451VCT6 is an ultra-low-power 32-bit Arm Cortex-M4 microcontroller with FPU, operating up to 80 MHz and providing 256 KB of Flash memory in a 100-lead LQFP package measuring 14 x 14 mm. The device also includes DFSDM capability and combines conventional MCU control with low-power operation and analog signal-processing resources. Its 100 DMIPS processing capability supports responsive control, data acquisition, and embedded user-interface workloads without requiring a separate digital signal processor. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one package. The STM32L451 belongs to the STM32L4 ultra-low-power family, where the product hierarchy is STM32L451 MCU, Arm Cortex-M4 microcontroller, 32-bit microcontroller, and embedded semiconductor. Within a system, it connects sensors, communications interfaces, analog converters, timers, and actuators while executing application firmware from its internal Flash memory. The STM32L451VCT6 combines an 80 MHz Arm Cortex-M4 processor core with 256 KB of Flash, a hardware floating-point unit, and extensive peripheral integration. DFSDM support is particularly useful for direct sampling of sigma-delta modulators and digital microphones. The DFSDM interface, conventional timers, serial interfaces, and low-power modes allow one microcontroller to control mixed analog and digital subsystems while limiting overall board area and external component count. Its ultra-low-power architecture is intended for systems where average energy use matters as much as peak processing performance. Low-power operating modes support battery-powered and intermittently energized equipment, while the 80 MHz operating point provides additional performance margin for control loops, communications buffering, and protocol handling. The integrated FPU accelerates floating-point calculations without requiring software emulation, helping reduce execution time in signal-processing and control applications. Typical applications include industrial sensor nodes, low-power data loggers, building automation controllers, compact audio acquisition systems, digital microphone equipment, portable measurement instruments, and connected industrial products. A board can place the MCU between an analog front end and communications subsystem, using DFSDM for selected data paths and serial peripherals for host or network communication. Firmware can then schedule acquisition and processing tasks according to the application's duty cycle. PCB design should preserve clean separation between sensitive analog inputs, digital interfaces, clock circuitry, and supply rails. Place decoupling capacitors close to the appropriate supply pins, route high-current and clock signals away from analog inputs, and provide continuous ground-plane paths beneath the device. Confirm pin availability, peripheral multiplexing, and boot configuration directly from the STM32L451xx datasheet before finalizing a new board or replacing an existing design. This product page combines the manufacturer's core device characteristics, procurement-oriented component data, and practical guidance for evaluating the STM32L451VCT6 in low-power embedded systems. It also highlights same-footprint alternatives so engineers can assess feature changes, memory differences, and peripheral trade-offs before committing a design to a specific MCU variant.

詢價 聯絡我們
STM32L451VEI6 - 80MHz 512KB Cortex-M4 MCU | STMicroelectronics
STM32L451VEI6

STM32L451VEI6 - 80MHz 512KB Cortex-M4 MCU | STMicroelectronics

The STMicroelectronics STM32L451VEI6 is an ultra-low-power 32-bit Arm Cortex-M4 microcontroller with a floating-point unit, operating up to 80 MHz and providing 512 KB of Flash memory and 160 KB of SRAM. The device is supplied in a 100-pin UFBGA package measuring 7 mm by 7 mm. Its combination of fast Cortex-M4 processing, analog peripherals, audio support, and low-power design makes it suitable for energy-sensitive embedded systems, connected sensors, industrial controls, and portable instruments. A microcontroller such as the STM32L451VEI6 integrates a processor core, memory, communication peripherals, analog interfaces, timers, and GPIO into one compact device. The STM32L4 family belongs to the broader embedded-controller hierarchy: Cortex-M4 processor core, 32-bit microcontroller, embedded semiconductor, and electronic control system. This integration reduces component count and allows firmware to coordinate sensing, control, communications, and real-time timing in one controller. The verified manufacturer information identifies an Arm Cortex-M4 32-bit RISC core, up to 80 MHz operation, 512 KB of Flash, and 160 KB of SRAM. The device also supports digital filtering and analog features identified by the manufacturer as DFSDM, analog, and audio capabilities. These resources support mixed-signal designs where a low-power MCU must acquire sensor data, perform signal conditioning, and communicate results without relying on a separate processor. The STM32L451VEI6 is positioned for embedded applications requiring more processing performance than a basic low-power MCU while retaining a compact package and energy-conscious architecture. Its Cortex-M4 core supports general-purpose control, communications, and floating-point-oriented workloads, while the integrated analog and audio peripherals can reduce system complexity. Exact peripheral assignments, voltage limits, current consumption, package pin functions, and production lifecycle details must be confirmed in the STMicroelectronics datasheet before final design release. Typical applications include industrial sensor nodes, low-power data loggers, connected measurement equipment, portable medical or diagnostic instruments, motor and actuator controllers, and compact IoT gateways. The 80 MHz core is useful for protocol handling, sampling workflows, control loops, and user-interface logic. Selection should begin with the required memory map, package footprint, peripheral set, operating voltage, clock tree, and low-power target. For PCB implementation, use the manufacturer package drawing and land pattern for the 100-UFBGA package rather than a generic BGA footprint. Confirm ball assignments, exposed-pad requirements, decoupling, power routing, and programming access in the datasheet. Also verify startup, clock, reset, and firmware-library support before committing the design to volume production. This product page combines verified manufacturer and distributor information, application-oriented engineering guidance, procurement context, and strict data-gap markers for specifications not present in the supplied sources. It is intended to support early component selection and sourcing, not to replace the complete STMicroelectronics reference documentation.

詢價 聯絡我們
STM32L452CCU6 - 80MHz Cortex-M4 MCU | STMicroelectronics
STM32L452CCU6

STM32L452CCU6 - 80MHz Cortex-M4 MCU | STMicroelectronics

The STMicroelectronics STM32L452CCU6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 processor, operating up to 80 MHz, with 256 KB of Flash memory in a 48-pin UFQFPN 7 x 7 mm package. Its 1.71 V to 3.6 V operating supply supports both 2.5 V and 3.3 V systems, while the -40 °C to +85 °C temperature range suits industrial and commercial equipment. An ultra-low-power microcontroller is a compact embedded controller designed to balance processing performance, standby consumption, and low-power operation. The STM32L4 family combines a real-time Cortex-M4 core with low-power modes, analog peripherals, communication interfaces, and energy-conscious peripherals. This makes the family useful for battery-operated sensors, compact industrial controllers, and connected devices that must wake quickly and process data without a continuously active high-power processor. The STM32L452CCU6 includes a Cortex-M4F core with floating-point hardware, 256 KB of Flash, and up to 100 DMIPS. According to the STMicroelectronics STM32L452xx manufacturer datasheet, the device supports a 1.71 V to 3.6 V power-supply range, five wakeup pins, and shutdown consumption as low as 22 nA. Its backup domain can draw 145 nA while retaining the real-time clock and 32 32-bit backup registers. The architecture is designed around efficient embedded control rather than high-performance computing. Hardware low-power modes reduce activity during idle periods, while the Cortex-M4F instruction set accelerates control loops and digital signal processing. USB device support broadens its use in portable logging, configuration interfaces, and human-interface adapters. The 7 x 7 mm UFQFPN package also saves board area, although its exposed pad and fine-pitch leads require careful PCB layout and thermal management. Typical uses include industrial sensor nodes, low-power data loggers, USB-connected measurement instruments, building automation controllers, portable medical accessories, and compact motor-control or condition-monitoring systems. The combination of 80 MHz processing, low-power shutdown modes, and a broad supply range supports designs that operate from regulated 3.3 V or 2.5 V rails. PCB implementation should follow the manufacturer pinout and land-pattern guidance. Place decoupling capacitors close to the supply pins, keep high-current and sensitive analog routes separated, and provide continuous copper beneath the exposed thermal pad. Validate the final assembly across the expected temperature range and confirm clock, USB, and low-power behavior with representative production hardware. This product page adds application guidance, same-package replacement analysis, comparison parameters, and practical PCB and power-management notes to the core technical information published by STMicroelectronics.

詢價 聯絡我們
STM32L452CEU6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics
STM32L452CEU6

STM32L452CEU6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics

The STMicroelectronics STM32L452CEU6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 processor, operating up to 80 MHz with 512 KB of embedded Flash and 160 KB of SRAM. It is packaged in a 48-pin UFQFPN measuring 7 x 7 mm and combines a floating-point unit, analog peripherals, audio resources, and external switched-mode power-supply support. An ultra-low-power microcontroller is a semiconductor device designed to balance processing capability with minimized energy consumption. The STM32L4 family belongs to the hierarchy of 32-bit RISC microcontrollers, embedded processors, and low-power embedded systems. This makes the STM32L452CEU6 suitable for battery-operated equipment, industrial controls, connected sensors, and portable products in which processing performance, analog measurement, and standby current are all important design considerations. Principal features include an 80 MHz Arm Cortex-M4 core, 512 KB of Flash, 160 KB of SRAM, and support for up to 100 DMIPS according to the manufacturer datasheet. The device integrates analog and audio capabilities alongside an external SMPS option. Its 32-bit architecture and floating-point unit support efficient control calculations and digital signal processing without requiring a separate accelerator for many embedded workloads. The 48-pin UFQFPN package provides access to the STM32L4 mixed-signal peripheral set while supporting compact, surface-mount PCB construction. Its supply-voltage listing includes 2.5 V and 3.3 V operating configurations. Designers should use the package drawing and pin-definition table in the manufacturer datasheet when assigning tracks, because the exposed pad, supply pins, ground pins, and analog functions must be connected according to the prescribed land pattern. Typical applications include low-power industrial sensor nodes, connected measurement equipment, battery-powered data loggers, compact audio-control systems, and embedded controls using an external DC-DC converter. The combination of 512 KB of program memory, 160 KB of SRAM, and an 80 MHz core also supports protocol gateways and supervisory controllers that need more local memory than a basic microcontroller. A critical design consideration is power-rail planning. Confirm the internal regulator, external SMPS configuration, decoupling requirements, and operating mode transitions in the manufacturer datasheet before layout. Place the required input and bulk capacitors close to their designated pins, provide a low-impedance ground structure, and account for thermal performance at the maximum expected ambient temperature. This product page combines the manufacturer's core device information with package guidance, sourcing details, application-oriented engineering considerations, and a conservative assessment of pin-compatible alternatives. It is designed to support component selection before the complete STM32L452xx electrical characteristics and firmware requirements are reviewed.

詢價 聯絡我們
STM32L452RCI6 - 80MHz Cortex-M4 256KB MCU | ST
STM32L452RCI6

STM32L452RCI6 - 80MHz Cortex-M4 256KB MCU | ST

The STMicroelectronics STM32L452RCI6 is an ultra-low-power 32-bit microcontroller built around the Arm Cortex-M4 processor, operating at up to 80 MHz and providing 256 KB of Flash memory in a 64-UFBGA 5 x 5 mm package. It combines a 100 DMIPS-class processing core with USB Device connectivity and extensive low-power peripherals for compact embedded systems. An ultra-low-power microcontroller is a semiconductor device designed to maintain processing capability while minimizing energy consumption during active operation, standby, and low-power modes. The STM32L4 family belongs to the Arm Cortex-M4 MCU, 32-bit microcontroller, embedded processor, and power-managed semiconductor hierarchy. It is suited to products that must process sensor information, control interfaces, or communicate over USB while operating from compact batteries or energy-limited industrial supplies. Key features include an Arm Cortex-M4 32-bit RISC core, a maximum operating frequency of 80 MHz, and 256 KB of Flash program memory. The device also includes USB Device support, an integrated floating-point unit for efficient arithmetic operations, and a peripheral set designed for low-power embedded control. Its 64-UFBGA package measures 5 x 5 mm, supporting compact layouts where a larger leaded package would be impractical. The 80 MHz Cortex-M4 core provides substantially more arithmetic throughput than lower-frequency microcontrollers while retaining the efficient instruction set and low-power behavior expected from the STM32L4 family. The integrated floating-point unit accelerates single-precision calculations without requiring a separate math accelerator, making the MCU suitable for real-time filtering, control loops, and general signal-processing tasks. Typical applications include USB-connected data loggers, compact industrial sensors, low-power building controllers, portable measurement equipment, and battery-operated IoT devices. The USB interface can simplify direct connectivity to a host computer, while the small UFBGA package supports dense boards and compact instrument housings. Developers must also account for high-density BGA assembly requirements, exposed-pad layout, and appropriate decoupling when creating a new PCB footprint. For reliable implementation, follow the pin-description table and land-pattern guidance in the manufacturer datasheet. Place every supply pin with its recommended local decoupling, provide a continuous ground reference beneath the device where supported by the package design, and validate the board assembly process before production. Firmware should use the documented low-power modes and preserve required GPIO, debug, and clock connections during shutdown states. This page combines the manufacturer specifications, procurement details, package information, confirmed family alternatives, application guidance, and engineering considerations needed to evaluate the STM32L452RCI6 before schematic capture, PCB layout, and prototype assembly.

詢價 聯絡我們
STM32L452RCT6 - 80MHz Cortex-M4 MCU | STMicroelectronics
STM32L452RCT6

STM32L452RCT6 - 80MHz Cortex-M4 MCU | STMicroelectronics

The STMicroelectronics STM32L452RCT6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 processor, operating at up to 80 MHz and delivering 100 DMIPS. It combines 256 KB of embedded Flash memory with 160 KB of SRAM in a 64-LQFP surface-mount package measuring 10 mm by 10 mm. The device is designed for compact, low-power embedded systems requiring substantial processing performance, analog control, communications, and flexible low-power operation. An ultra-low-power microcontroller is an integrated semiconductor that balances processing capability with minimized energy consumption. Within the product hierarchy, it is an Arm Cortex-M4 MCU, a 32-bit RISC microcontroller, and a member of the STM32L4 power-management-oriented product family. Low-power operating modes allow the processor to remain responsive while reducing energy use during idle, standby, shutdown, and battery-backed operation. This makes the device suitable for systems where average power consumption matters as much as peak processing performance. The STM32L452RCT6 integrates 52 I/O pins, a floating-point unit, USB device connectivity, digital filtering and analog conversion capabilities, and interfaces including CAN and QSPI. Its operating supply range of 1.71 V to 3.6 V supports low-voltage battery-powered designs. The manufacturer lists operating-temperature options from -40 °C to 85 °C or 125 °C, allowing selection according to environmental requirements. FlexPowerControl supports explicit control of low-power behavior, while Stop and Shutdown modes can reduce consumption when extended active processing is unnecessary. The Cortex-M4 architecture provides a strong balance of performance and efficiency for embedded control, sensor processing, communications, and human-interface tasks. Its floating-point unit accelerates mathematical operations that would otherwise require software emulation. The 256 KB Flash partition supports firmware and application code, while 160 KB of SRAM provides working memory for protocol stacks, data buffers, graphics, and control algorithms. This combination of memory capacity and peripheral integration reduces the need for external components in moderately complex embedded designs. Typical applications include low-power USB-connected sensors, industrial monitoring equipment, portable medical instruments, USB data loggers, energy-management controllers, compact human-interface panels, and connected embedded products. The USB device interface is particularly useful for configuration, data transfer, and firmware update workflows. CAN and QSPI connectivity broaden the design options for industrial networks and external flash-memory expansion. Developers can also use analog peripherals and digital filtering for direct acquisition and conditioning of sensor signals. Power-rail and decoupling decisions are critical in a 1.71 V to 3.6 V design. Place the required input, output, and bypass capacitors close to their corresponding pins, keep sensitive analog and communication traces away from high-current switching paths, and verify all timing constraints against the STM32L452xx manufacturer datasheet. Firmware should also use the device's clock, flash, and low-power configuration procedures rather than treating the MCU as a conventional 80 MHz processor. This product page combines manufacturer specifications, package and application guidance, sourcing workflows, and same-family replacement analysis. It also distinguishes documented characteristics from details that require confirmation with the manufacturer datasheet, helping engineers plan PCB reuse, firmware validation, power-budget analysis, and second-source qualification with greater confidence.

詢價 聯絡我們
STM32L452RET6 - Ultra-Low-Power Cortex-M4 MCU 80MHz 512KB | ST
STM32L452RET6

STM32L452RET6 - Ultra-Low-Power Cortex-M4 MCU 80MHz 512KB | ST

The STMicroelectronics STM32L452RET6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 core with FPU, operating at up to 80 MHz with 512 KB of Flash and 160 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It features a wide 1.71 V to 3.6 V supply range, USB Device, DFSDM, and integrated SMPS support, while consuming as little as 22 nA in Shutdown mode and 145 nA in VBAT mode. What is an ultra-low-power ARM Cortex-M4 microcontroller? It is a 32-bit processor core designed for embedded systems that balances computational performance with exceptionally low energy consumption. The Cortex-M4 includes a single-precision floating-point unit (FPU) and DSP extensions, enabling efficient math-intensive workloads. In the system hierarchy, a microcontroller (MCU) is a complete computer-on-a-chip integrating CPU, memory, and peripherals, and belongs to the embedded processor category within the broader semiconductor landscape. The STM32L4 series specifically targets energy-constrained applications, extending battery life in portable, wearable, and IoT devices. Key features of the STM32L452RET6 include seven low-power modes (Sleep, Low-power run, Low-power sleep, Stop 0/1/2, Standby, Shutdown), a 12-bit ADC with hardware oversampling, a 12-bit DAC, two comparators, and an operational amplifier. The device also integrates a true random number generator (TRNG), AES-256 hardware crypto accelerator, secure firmware install, and a 96-bit unique ID. Communication interfaces include USB 2.0 Full-Speed Device, three USARTs, two UARTs, three I2C, three SPI, one CAN, and one SDMMC. Technically, the STM32L452RET6 is built on a low-leakage 90 nm process and supports up to 100 DMIPS / 273 CoreMark. The integrated SMPS step-down converter generates the core voltage internally, further reducing active current. A flexible memory protection unit (MPU), FSMC external memory controller, and Quad-SPI (in higher-density siblings) support external memories. The device operates across -40 C to +85 C (or +125 C with the '6' high-temp suffix variant). Typical applications include industrial sensors, smart meters, healthcare devices, wearable electronics, asset trackers, and IoT endpoints. Its combination of ultra-low quiescent current, Cortex-M4 DSP performance, and rich analog peripherals makes it ideal for battery-powered metering, medical wearables, and remote sensor nodes. When designing, leverage Stop 2 mode with RTC for periodic wake-up duty cycles, place 100 nF decoupling on every VDD/VSS pair, and use STM32CubeMX + STM32CubeIDE for clock tree configuration, peripheral init, and power-mode tuning. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
STM32L452RET6P - 80MHz Cortex-M4 MCU, 512KB Flash | STMicroelectronics
STM32L452RET6P

STM32L452RET6P - 80MHz Cortex-M4 MCU, 512KB Flash | STMicroelectronics

The STMicroelectronics STM32L452RET6P is an ultra-low-power Arm Cortex-M4 32-bit microcontroller plus FPU, operating at up to 80 MHz with 100 DMIPS, integrating 512 KB of Flash and 160 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It supports a 1.71 V to 3.6 V supply and is offered in -40 C to 85/125 C temperature grades for industrial and portable designs. An ultra-low-power MCU (ULP-MCU) is a microcontroller class engineered to minimise active and standby energy consumption through FlexPowerControl, multiple low-power modes (Shutdown, Standby, Stop, VBAT), and fast wakeup times. The STM32L4 family sits in ST's low-power hierarchy as Cortex-M4F -> STM32L4 series -> ultra-low-power MCU -> 32-bit microcontroller -> embedded MCU, balancing DSP capability, analog integration and energy efficiency for battery-powered edge devices. Key features include: Cortex-M4 with FPU and 100 DMIPS throughput; 512 KB single-bank Flash plus 160 KB SRAM; integrated SMPS step-down converter for core supply; USB 2.0 Full-Speed Device with embedded PHY and dedicated DFS (dedicated oscillator); two 12-bit ADCs, two 12-bit DACs, two op-amps and two comparators; rich connectivity including CAN 2.0B, two I2C, three SPI, four USART, two UART and one LPUART; plus 8x40 (4x40-segment) LCD driver and AES-256 hardware encryption. Shutdown current is 22 nA (5 wakeup pins), VBAT mode draws 145 nA, and Stop mode with RTC reaches about 1.1 uA typical. The device integrates a Cortex-M4F core with single-precision FPU, MPU and DSP extensions, plus ST's proprietary ART Accelerator for zero-wait-state Flash execution at full 80 MHz. Embedded SMPS, low-power voltage regulator, and independent RTC supply domain are partitioned to support advanced run/sleep/shutdown state machines without losing backup registers. Typical applications are fitness/wearable sensor hubs, smart-meter and asset-tracking endpoints, industrial sensor nodes, medical wearables, low-power PC peripherals with USB, audio playback paths leveraging the on-chip DFSDM and SAI, and home appliances with LCD display panels. When designing with STM32L452RET6P, prefer BOR-enabled power-up sequencing, route the SMPS inductor carefully on a 4-layer PCB to minimise radiated noise, and use ST's STM32CubeMX and HAL/LL libraries to accelerate peripheral configuration. Consider the higher-density STM32L4R/4A part if the application needs 1 MB Flash. This page synthesises distributor pricing, drop-in LQFP-64 alternatives and practical design notes not collated on the manufacturer datasheet, helping procurement and embedded engineers evaluate the STM32L452RET6P against contemporary ARM Cortex-M4F peers.

詢價 聯絡我們
STM32L452RET6TR - 80MHz 512KB Flash MCU | STMicroelectronics
STM32L452RET6TR

STM32L452RET6TR - 80MHz 512KB Flash MCU | STMicroelectronics

The STMicroelectronics STM32L452RET6TR is an ultra-low-power Arm Cortex-M4 32-bit microcontroller with FPU running at up to 80 MHz, featuring 512 KB of Flash memory and 160 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It delivers 100 DMIPS at 80 MHz while drawing only 84 uA/MHz in run mode, making it one of the most power-efficient Cortex-M4 devices in the STM32L4 series. An ultra-low-power microcontroller (MCU) is a single-chip computer that integrates a processor core, non-volatile program memory (Flash), volatile data memory (SRAM), and a broad set of peripherals such as ADCs, DACs, timers, and serial interfaces. The STM32L452RET6TR sits in the STM32L4 family, which is part of the broader STM32 32-bit MCU portfolio, itself a member of the Arm Cortex-M ecosystem. Ultra-low-power MCUs are designed for battery-powered and energy-harvesting systems where every microamp matters, while still providing enough compute throughput for real-time control and signal processing. Key features include FlexPowerControl with a 1.71 V to 3.6 V supply range, 145 nA in VBAT mode for RTC and 32x32-bit backup registers, 22 nA in Shutdown mode with 5 wakeup pins, and a 12-bit ADC with hardware oversampling. The device also integrates a USB Device controller, DFSDM (digital filter for sigma-delta modulators), and multiple low-power timers, enabling always-on sensing with minimal energy cost. The STM32L452RET6TR is built on ST's ultra-low-leakage 90 nm process and uses a proprietary adaptive real-time memory accelerator to achieve 100 DMIPS at 80 MHz without wait states. Its analog peripherals include two 12-bit ADCs, one 12-bit DAC, and two ultra-low-power comparators, allowing direct interfacing with sensors and eliminating external signal-conditioning components in many designs. Typical applications include portable medical monitors, industrial IoT sensor nodes, smart metering, wearable fitness trackers, and battery-operated asset trackers. The combination of 512 KB Flash, 160 KB SRAM, and a rich analog front end makes it suitable for edge processing tasks such as filtering, FFT, and motor control. When designing with this device, pay close attention to the VDD/VBAT power architecture and the decoupling network. The 64-pin LQFP package provides 52 user I/O pins, so plan pin allocation carefully to avoid conflicts between the USB, ADC, and timer functions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, second-sourcing, and layout decisions.

詢價 聯絡我們
STM32L452REY6TR - Ultra-low-power ARM Cortex-M4 MCU | STMicroelectronics
STM32L452REY6TR

STM32L452REY6TR - Ultra-low-power ARM Cortex-M4 MCU | STMicroelectronics

The STM32L452REY6TR is an ultra-low-power 32-bit microcontroller from STMicroelectronics, based on the ARM Cortex-M4 core with FPU. It operates at a maximum frequency of 80 MHz and delivers 100 DMIPS with 1.25 DMIPS/MHz, making it suitable for a wide range of battery-powered and energy-efficient applications. The device features 512 KB of Flash memory and 160 KB of SRAM, providing ample storage for complex firmware and data buffering. What is an ARM Cortex-M4 microcontroller? It is a 32-bit processor core designed for embedded systems, offering a balance of performance, power efficiency, and rich peripheral integration. The Cortex-M4 includes a floating-point unit (FPU) and DSP instructions, enabling efficient handling of mathematical and signal-processing tasks. In the system hierarchy, the STM32L452REY6TR sits at the application processor level, managing sensors, communication interfaces, and control loops, while interfacing with memory, power management, and external peripherals. Key features include an operating voltage range of 1.71V to 3.6V, multiple low-power modes (Sleep, Low-power run, Low-power sleep, Stop 0/1/2, Standby, and Shutdown) with current consumption as low as 28 µA in Stop 2 mode, and a rich set of peripherals including multiple USARTs, SPIs, I2Cs, USB 2.0 FS, CAN, and 12-bit ADCs/DACs. The device also integrates a true random number generator (TRNG), a CRC calculation unit, and a 12-channel DMA controller. The STM32L452REY6TR is built on ST's ultra-low-power technology, featuring a flexible power architecture with internal regulators and a low-power RTC. It supports a wide temperature range of -40°C to +85°C and is available in a 64-pin UFBGA package (Y6 suffix), which is ideal for space-constrained designs. The package measures 4.0 x 4.0 mm with a 0.5 mm pitch, offering excellent thermal performance and compactness. Typical applications include industrial sensors, smart meters, wearable devices, medical monitoring equipment, and IoT edge nodes. The combination of low power consumption, high performance, and extensive connectivity makes it a versatile choice for battery-operated systems that require advanced processing capabilities. When designing with this MCU, careful attention to power supply decoupling and PCB layout is essential to achieve the specified low-power performance. Use multiple decoupling capacitors close to the power pins and follow the layout guidelines in the datasheet to minimize noise and ensure reliable operation.

詢價 聯絡我們
STM32L452VCI6 - 80MHz Cortex-M4 MCU | STMicroelectronics
STM32L452VCI6

STM32L452VCI6 - 80MHz Cortex-M4 MCU | STMicroelectronics

STMicroelectronics STM32L452VCI6 is an ultra-low-power 32-bit Arm Cortex-M4 microcontroller with floating-point unit, an 80 MHz operating frequency, 256 KB of Flash memory, and a 100-UFBGA 7 x 7 mm package. The device combines USB Device connectivity, DFSDM capability, analog functions, and embedded peripherals in a compact surface-mount package for power-conscious embedded systems. An ultra-low-power microcontroller is a semiconductor controller optimized to complete sensing, control, communications, and data-processing tasks while minimizing active and standby energy consumption. Within the product hierarchy, the STM32L452VCI6 is an Arm Cortex-M4 MCU, a 32-bit RISC microcontroller, and a member of STM32L4 power management-oriented embedded devices. Its USB and DFSDM interfaces distinguish it from basic low-power MCUs while its 7 x 7 mm package supports space-constrained designs. The principal verified features include an Arm Cortex-M4 processor with FPU, operation up to 80 MHz, and 256 KB of Flash storage. The Cortex-M4 architecture supports efficient embedded control and digital signal-processing workloads, while the FPU accelerates suitable floating-point calculations. USB Device support enables the MCU to communicate with a host computer or USB-equipped peripheral, and DFSDM provides a dedicated path for external analog data acquisition. The STM32L452VC family is positioned for applications requiring a balance between processing performance, low-power operation, analog connectivity, and compact packaging. Its 256 KB of Flash provides embedded program storage, while the STM32L4 platform is designed for energy-sensitive products that need more capability than a basic low-power MCU but do not require a high-performance application processor. Typical uses include USB-connected data acquisition equipment, low-power industrial sensing modules, compact audio or communication products, environmental monitoring devices, and portable instrumentation. DFSDM is particularly relevant when an application must acquire signals through an external sigma-delta converter while avoiding a general-purpose ADC for every input. The 100-UFBGA package also helps reduce board area where that benefit outweighs assembly and inspection complexity. Designers should verify the complete pin assignment, exposed-pad requirements, power sequencing, decoupling, and operating-temperature limits against the manufacturer datasheet before layout release. The 7 x 7 mm BGA footprint also demands assembly processes capable of inspecting fine-pitch solder joints. Firmware and peripheral configurations should be checked in detail because USB, DFSDM, clocking, and low-power modes can affect both board design and software architecture. This product page consolidates verified manufacturer and distributor information, distinguishes the target from same-family options, and adds application guidance, comparison parameters, and practical design cautions that are not organized together in the manufacturer datasheet.

詢價 聯絡我們
STM32L452VCT6 - Ultra-Low-Power ARM Cortex-M4 MCU | STMicroelectronics
STM32L452VCT6

STM32L452VCT6 - Ultra-Low-Power ARM Cortex-M4 MCU | STMicroelectronics

The STM32L452VCT6 is an ultra-low-power 32-bit microcontroller from STMicroelectronics, based on the ARM Cortex-M4 core with FPU. It operates at a maximum frequency of 80 MHz and delivers 100 DMIPS with 1.25 DMIPS/MHz, making it suitable for a wide range of battery-powered and energy-efficient applications. The device features 256 KB of Flash memory and 160 KB of SRAM, providing ample storage for complex firmware and data buffering. What is an ARM Cortex-M4 microcontroller? It is a 32-bit processor core designed for embedded systems, offering a balance of performance, power efficiency, and rich peripheral integration. The Cortex-M4 includes a floating-point unit (FPU) and DSP instructions, enabling efficient handling of mathematical and signal-processing tasks. In the system hierarchy, a microcontroller (MCU) integrates a processor core, memory, and programmable peripherals on a single chip, serving as the 'brain' of embedded systems. The STM32L4 series specifically targets ultra-low-power applications, extending battery life in portable and IoT devices. Key features of the STM32L452VCT6 include multiple low-power modes (Sleep, Low-power run, Low-power sleep, Stop 0/1/2, Standby, and Shutdown) with current consumption as low as 28 µA in Stop 2 mode with SRAM retention. It integrates a 12-bit ADC with 5 Msps, two 12-bit DACs, two comparators, and two operational amplifiers. Communication interfaces include I2C, SPI, USART, UART, LPUART, SAI, and CAN, along with USB 2.0 full-speed device/host/OTG. The device also features a true random number generator (TRNG), a CRC calculation unit, and a 96-bit unique ID. The STM32L452VCT6 is built on ST's ultra-low-power technology with an adaptive voltage scaling and a flexible power architecture. It includes a multi-speed internal RC oscillator (16 MHz) and a low-power internal oscillator (32 kHz), reducing external component count. The device supports external crystal oscillators for high-accuracy timing and includes a real-time clock (RTC) with calendar and alarm functions. The integrated LCD driver supports up to 8x40 segments, enabling direct connection to segment LCDs without external drivers. Typical applications include industrial sensors, smart meters, healthcare devices, wearable fitness trackers, and IoT edge nodes. Its ultra-low-power modes and rich analog peripherals make it ideal for battery-operated systems that require long operational life. The device also supports secure firmware updates with its read-out protection and memory protection unit, enhancing system security. When designing with the STM32L452VCT6, pay attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 4.7 µF capacitor on the main VDD rail. Use the internal LDO or external SMPS step-down converter for optimal power efficiency. The VBAT pin should be connected to a backup battery or tied to VDD if not used. For low-power operation, configure unused GPIOs as analog inputs to minimize leakage current.

詢價 聯絡我們
STM32L462CEU6 - 80MHz Cortex-M4 MCU | STMicroelectronics
STM32L462CEU6

STM32L462CEU6 - 80MHz Cortex-M4 MCU | STMicroelectronics

STMicroelectronics STM32L462CEU6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 processor, operating up to 80 MHz with 512 KB of Flash memory and USB device connectivity in a 48-pin UFQFPN package. The device combines a 100 DMIPS-class Cortex-M4 core with floating-point capability, 160 KB of SRAM, AES-256 hardware acceleration, and DFSDM support. An ultra-low-power microcontroller is designed to balance responsive computation with low energy consumption during active operation and low-power standby states. The STM32L4 family sits within the hierarchy of embedded MCU, 32-bit RISC microcontroller, low-power processor, and power-management-oriented semiconductor. These characteristics make the STM32L462CEU6 appropriate for compact products where USB connectivity, security, and efficient control processing are required in the same device. Principal features include an Arm Cortex-M4 core with FPU, a maximum operating frequency of 80 MHz, 512 KB of program Flash, 160 KB of SRAM, and USB device support. The hardware AES-256 accelerator supports encrypted data handling without offloading every cryptographic operation to software. DFSDM interfaces can work with external sigma-delta converters, helping designers build compact measurement or signal-conditioning systems. The STM32L462CEU6 belongs to the STM32L462xx family and uses an Arm Cortex-M4 RISC architecture. Its combination of high processing speed, low-power design, and dedicated peripherals reduces the need for separate USB controllers, security engines, or high-speed analog interface devices. Firmware can integrate USB communications, control logic, secure data storage, and sensor acquisition within a unified embedded architecture. Typical uses include USB-connected data acquisition, compact industrial controllers, secure access equipment, low-power sensor nodes, portable medical or diagnostic modules, and USB-connected human-interface devices. The 48-pin package provides a practical balance between peripheral access, board area, and manufacturing complexity for applications that need more I/O than an ultra-small MCU package can offer. When laying out the PCB, follow the manufacturer pinout, exposed-pad, decoupling, and thermal-via guidance exactly. Place bypass capacitors close to the supply pins, provide a continuous ground reference beneath the device where the package permits, and confirm USB impedance-controlled routing and ESD protection before release to production. This page consolidates the exact STM32L462CEU6 specifications, same-footprint alternatives, application guidance, and design checks engineers need when planning an ultra-low-power USB-capable embedded system. It also identifies where pin-level, electrical-limit, lifecycle, and supply details must be confirmed in the official STMicroelectronics documentation.

詢價 聯絡我們
STM32L471QGI6 - 80MHz Cortex-M4 1MB MCU | STMicroelectronics
STM32L471QGI6

STM32L471QGI6 - 80MHz Cortex-M4 1MB MCU | STMicroelectronics

The STMicroelectronics STM32L471QGI6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 RISC core, operating at up to 80 MHz, with 1 MB of Flash memory and 128 KB of SRAM in a 132-pin UFBGA package measuring 7 x 7 mm. It supports a 1.71 V to 3.6 V supply range and is specified for -40°C to +85°C operation. A microcontroller is a programmable system-on-chip that integrates a CPU, memory, peripheral interfaces, and clocking into one device. The STM32L4 family belongs to the hierarchy microcontroller -> embedded processor -> programmable controller -> semiconductor. Its low-power design and broad peripheral integration make this class of device useful for compact embedded products that must balance processing capability, energy efficiency, and board area. Key features include the 80 MHz Arm Cortex-M4 core, 1 MB of Flash, 128 KB of SRAM, 12-bit conversion peripherals, and support for up to 109 I/O functions according to the listed product specifications. The STM32L471QGI6 also includes DFSDM capability, providing a digital filter for sigma-delta modulator-based signal acquisition. Its 132-UFBGA package supports a high pin count while occupying only 7 x 7 mm of board area. The device operates from a 1.71 V to 3.6 V supply and combines an Arm Cortex-M4 processor with integrated Flash and SRAM for compact firmware storage and working memory. Its industrial temperature range covers -40°C to +85°C, supporting applications in consumer equipment, industrial controls, connected sensors, portable instrumentation, and compact automation products. The broad supply range also allows deployment from low-voltage battery-powered systems through conventional 3.3 V equipment. Typical applications include low-power sensor nodes, industrial data-acquisition modules, portable measurement instruments, compact motor and process controllers, and connected embedded-control products. In each case, the 80 MHz processing rate supports responsive control and communication tasks, while DFSDM and the 12-bit conversion capabilities support analog-signal acquisition. The 7 x 7 mm UFBGA package is especially useful when component footprint and I/O density are important design constraints. PCB design requires careful attention to the 132-pin UFBGA escape routing and thermal management. Follow the manufacturer's land pattern, pin table, and recommended decoupling arrangement exactly; assign every ball from the package drawing rather than relying on inferred pin functions. For low-power operation, select the appropriate clock, peripheral, and sleep configuration in firmware, and confirm timing at the minimum operating voltage and maximum temperature. This product page consolidates the key device characteristics, sourcing information, application guidance, and engineering considerations needed to evaluate the STM32L471QGI6 before starting a compact embedded-control design.

詢價 聯絡我們
STM32L471RET6 - ARM Cortex-M4F 80MHz MCU | STMicroelectronics
STM32L471RET6

STM32L471RET6 - ARM Cortex-M4F 80MHz MCU | STMicroelectronics

The STMicroelectronics STM32L471RET6 is a high-performance ARM Cortex-M4F based microcontroller with floating-point unit (FPU) running at up to 80 MHz. It is part of the STM32L4 series, designed for ultra-low-power applications without compromising performance. The device integrates 512 KB of flash memory and 128 KB of SRAM, along with a rich set of peripherals including multiple 12-bit ADCs, DACs, comparators, op-amps, and advanced communication interfaces such as USART, SPI, I2C, CAN, and USB OTG FS. It is available in a 64-pin LQFP package (LQFP64) with a 10x10 mm body and 0.5 mm pitch. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory (flash and SRAM), and programmable input/output peripherals on a single chip. Microcontrollers are the brains of countless electronic devices, from automotive engine control units to wearable health monitors. In the system hierarchy, a microcontroller is a type of embedded processor, which falls under the broader category of integrated circuits (ICs) and semiconductors. The STM32L471RET6 is a mid-range MCU in the STM32L4 family, positioned between the lower-power STM32L0/L1 series and the higher-performance STM32F4 series, offering a balance of energy efficiency and processing capability. Key features of the STM32L471RET6 include its ultra-low-power modes (Sleep, Low-power run, Low-power sleep, Stop 0/1/2, Standby, and Shutdown) with current consumption as low as 100 nA in Shutdown mode. The device supports a wide supply voltage range of 1.71V to 3.6V, making it suitable for battery-powered applications. It also features a 12-bit ADC with hardware oversampling, a 12-bit DAC, and a true random number generator (TRNG). The FPU accelerates mathematical computations, which is beneficial for signal processing and control algorithms. The MCU is manufactured using ST's 90 nm process technology, enabling low dynamic power consumption. Technical depth: The STM32L471RET6 is built around the ARM Cortex-M4F core with DSP instructions and a single-precision FPU. It includes a memory protection unit (MPU) for enhanced security and reliability. The device supports up to 8x32-bit timers, including a low-power timer (LPTIM) that can operate in Stop mode. Communication peripherals include 3x USART, 3x SPI, 3x I2C, 1x CAN, 1x USB OTG FS, and 1x SAI (serial audio interface). The ADC has a resolution of 12 bits with up to 16 external channels and can operate at up to 5 Msps. The DAC has two channels with 12-bit resolution. The device also includes a flexible memory controller (FMC) for external memory expansion, supporting SRAM, PSRAM, NOR, and NAND flash. Typical applications include industrial sensors and actuators, smart meters, medical devices (e.g., glucose monitors, infusion pumps), wearable fitness trackers, IoT nodes, and portable instrumentation. The ultra-low-power modes and rich analog peripherals make it ideal for battery-operated devices that require long battery life and precise analog measurements. For example, in a smart meter, the STM32L471RET6 can handle metrology calculations, communication protocols, and display control while consuming minimal power in sleep mode between measurements. Design consideration: When designing with the STM32L471RET6, pay attention to the power supply decoupling. Place a 100 nF ceramic capacitor close to each VDD pin and a 4.7 uF capacitor at the main power input. For the VDDA pin, use a dedicated 1 uF capacitor to ensure stable analog performance. Also, configure the clock system carefully: the device can run from an internal 16 MHz HSI oscillator, but for precise timing, use an external 8 MHz crystal with appropriate load capacitors. The boot pins (BOOT0 and BOOT1) must be set correctly for the desired boot mode (flash, system memory, or SRAM).

詢價 聯絡我們
STM32L471VET6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics
STM32L471VET6

STM32L471VET6 - 80MHz Cortex-M4 512KB MCU | STMicroelectronics

The STMicroelectronics STM32L471VET6 is an ultra-low-power, 32-bit microcontroller based on the Arm Cortex-M4 processor, operating at up to 80 MHz and packaged in a 100-pin LQFP measuring 14 x 14 mm. It provides 512 KB of embedded Flash memory, 128 KB of SRAM, and an integrated floating-point unit for efficient control-oriented and connected embedded processing. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The STM32L471VET6 belongs to the STM32L4 family of 32-bit Arm Cortex-M4 microcontrollers, combining low-power operation with substantial processing performance. Its architecture supports connected industrial, sensor, metering, and equipment-control applications where energy efficiency, real-time response, and a broad peripheral set are important. Principal device attributes include an 80 MHz maximum clock, 512 KB Flash, 128 KB SRAM, a 32-bit Arm Cortex-M4 core, and single-precision floating-point support. The 100-pin LQFP package exposes substantially more I/O than smaller MCU packages, making it suitable for systems requiring several communication peripherals, analog inputs, timers, and external memory interfaces. Digital signal processing benefits from the Cortex-M4 FPU while retaining deterministic embedded-control operation. The STM32L4 architecture balances processing capability with low-power modes for battery-operated and industrial systems. Its 512 KB Flash provides room for application firmware, boot code, configuration data, and protocol libraries, while 128 KB of SRAM supports working buffers and real-time control tasks. The exact supported operating voltage, clock tree, peripheral configuration, current consumption, and temperature limits must be selected from the manufacturer datasheet and device option-byte configuration. Typical applications include industrial sensor nodes, low-energy wireless equipment, building automation, portable instrumentation, motor and motion control, and connected measurement systems. The combination of 80 MHz processing, hardware floating-point capability, 512 KB Flash, and 100-pin I/O capacity supports complex control algorithms, local data processing, and communication protocol stacks while maintaining a compact surface-mount footprint. PCB design should preserve the pin assignment and decoupling requirements defined in the manufacturer datasheet. Place the required input and output capacitors close to their associated supply pins, route high-current and sensitive analog nets away from fast-switching nodes, and use a continuous ground plane. Confirm the exact pin names, alternate functions, oscillator requirements, and programming interface before releasing the PCB. This product page combines the manufacturer specifications, package information, sourcing references, drop-in alternatives, application guidance, and design considerations needed to evaluate the STM32L471VET6. It also distinguishes directly pin-compatible STM32L4 options from broader functional alternatives so engineers can assess replacement decisions against memory, peripheral, and firmware requirements.

詢價 聯絡我們
STM32L471VGT6 - 80MHz Cortex-M4 1MB MCU | STMicroelectronics
STM32L471VGT6

STM32L471VGT6 - 80MHz Cortex-M4 1MB MCU | STMicroelectronics

The STMicroelectronics STM32L471VGT6 is an ultra-low-power 32-bit Arm Cortex-M4 microcontroller with an operating frequency up to 80 MHz, 1 MB of Flash memory, a single-precision FPU, and a 100-pin LQFP package measuring 14 x 14 mm. It is designed for embedded systems requiring efficient Cortex-M4 processing, extensive mixed-signal connectivity, and low-power operation in industrial, consumer, medical, and connected-equipment applications. An ultra-low-power microcontroller is a semiconductor device optimized to perform control, measurement, communications, and data-processing tasks while minimizing energy consumption. The STM32L471 belongs to STMicroelectronics’ STM32L4 family, combining the Arm Cortex-M4 processor hierarchy with energy-efficient embedded control, analog peripherals, digital interfaces, and memory in one integrated device. Its architecture is suitable for designs that must balance processing capability, peripheral integration, board area, and power efficiency. The STM32L471VGT6 combines an 80 MHz Arm Cortex-M4 core with 1 MB of Flash and a single-precision floating-point unit. The Cortex-M4 processor supports the standard Arm single-precision data-processing instructions and a complete set of DSP instructions. This combination gives embedded developers a compact platform for control loops, signal processing, protocol handling, and floating-point calculations without requiring a separate DSP or math coprocessor. The device also includes digital and analog resources suited to mixed-signal embedded products. Its broad peripheral integration can reduce the number of discrete components on a compact PCB. The manufacturer’s STM32L471xx documentation identifies the family as an ultra-low-power Cortex-M4 MCU platform and confirms the 80 MHz maximum operating frequency and single-precision FPU architecture used by this ordering code. Typical applications include industrial sensor controllers, low-power data loggers, medical monitoring equipment, building controls, communication modules, compact motor-control systems, and battery-powered IoT devices. The 100-pin LQFP package provides ample external connectivity for mixed-signal boards, while the 1 MB Flash capacity provides room for larger firmware images, boot routines, diagnostics, and application logic. Designers should preserve the voltage and decoupling requirements specified in the manufacturer datasheet, place decoupling capacitors close to the supply pins, and maintain clear separation between sensitive analog inputs, high-speed digital signals, and switching-power circuitry. Firmware compatibility between related STM32L4 devices should be verified rather than assumed, particularly when changing memory configuration, peripheral availability, or boot behavior. This page organizes the STM32L471VGT6’s core identifiers, package information, sourcing path, and engineering guidance with practical context for PCB integration. It also distinguishes exact device attributes from data that must be confirmed in the manufacturer’s pin table and electrical-characteristics documentation before a new board is released to production.

詢價 聯絡我們
STM32L471ZGT6 - 1MB Flash 80MHz Cortex-M4 MCU | STMicroelectronics
STM32L471ZGT6

STM32L471ZGT6 - 1MB Flash 80MHz Cortex-M4 MCU | STMicroelectronics

The STMicroelectronics STM32L471ZGT6 is an ultra-low-power 32-bit microcontroller based on the high-performance Arm Cortex-M4 RISC core with FPU, operating at frequencies up to 80 MHz, packaged in a 144-pin LQFP. The device integrates 1 MB of Flash, 128 KB of SRAM, and a rich peripheral set including CAN, USB, multiple UART/SPI/I2C interfaces, 12-bit ADCs, and a real-time clock for energy-sensitive embedded control applications. An ultra-low-power microcontroller (MCU) is a class of microprocessor that minimizes active and standby current consumption through techniques such as voltage scaling, multiple low-power operating modes, peripheral clock gating, and integrated DC-DC converters. The STM32L4 family extends this concept with the Cortex-M4 core plus DSP instructions and a single-precision floating-point unit, enabling digital signal processing alongside efficient power management. Within the broader taxonomy, the STM32L471ZGT6 sits in the hierarchy MCU -> Arm Cortex-M microcontroller -> ultra-low-power MCU -> power management IC ecosystem. Key features include a 1.8 V to 3.6 V supply range, batch acquisition mode for ADC, multiple low-power modes (Stop, Standby, Shutdown) drawing as little as a few hundred nanoamperes with RTC retention, a built-in 12-bit 5 Msps ADC, two DAC channels, USB 2.0 Full-Speed device/host, three I2C, three SPI, three USART plus UART, two CAN 2.0B, SDMMC, and a Crypt/AES-256 hardware accelerator. The 144-pin LQFP package supports ample GPIO for industrial control panels and sensor hubs. The STM32L471 uses a Cortex-M4 core with FPU and DSP extensions, providing 1.25 DMIPS/MHz and a CoreMark score in the hundreds, balancing DSP capability with extreme energy efficiency. The integrated LDO(Dragon) voltage regulator and switchable DC-DC buck converter allow dynamic trade-off between quiescent current and peak performance. Typical applications include industrial sensor nodes, wearable medical monitors, smart metering, battery-powered IoT gateways, and motor control subsystems where extended battery life and deterministic real-time response are simultaneously required. The 1 MB Flash enables on-board firmware with secure bootloaders, OTA stacks, and rich protocol libraries. When designing, always verify the supply decoupling network (1uF + 100nF + 4.7uF bulk) per ST AN4325 reference design and consider the 32 kHz LSE crystal selection for RTC accuracy. The 144-LQFP package simplifies layout but requires thermal relief for applications pushing >70% CPU duty. This page synthesizes verified distributor pricing, parametric drop-in alternatives, and practical low-power design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們