A3P125-PQ208I - 125K Gate Flash FPGA | Microchip Technology
MPN: A3P125-PQ208I ✓ 啟用中A3P125-PQ208I 概覽
An FPGA is a programmable digital semiconductor used to implement logic functions, interfaces, control systems, and signal processing by configuring an internal array of configurable logic blocks and routing resources. The ProASIC3 family combines nonvolatile flash configuration with a single-chip, reprogrammable implementation, allowing a design to be updated without using a separate configuration memory device. Its architecture falls within the broader FPGA and CPLD hierarchy of programmable logic semiconductors.
The A3P125 device provides 36,864 internal SRAM bits and up to 133 user I/Os according to the product listing. Its configurable architecture supports system-level logic consolidation, while flash-based configuration provides Instant On operation after programming. The 208-pin plastic QFP package measures 28 mm by 28 mm, has a 0.50 mm terminal pitch, and is 3.40 mm high. The suffix I denotes the ordering configuration listed by Microchip Technology for this device.
A key implementation advantage is migration support within the ProASIC3 family. Microchip's A3P250 migration application note identifies A3P125 as a lower-logic-density destination and emphasizes package-based pin compatibility within the family. This makes the A3P125-PQ208I relevant to prototype-to-production consolidation and ASIC-like embedded control designs, subject to device-specific timing, resource, and I/O validation.
Typical uses include industrial control and automation, communications infrastructure, instrumentation, embedded protocol handling, and low-volume ASIC replacement. The 133 I/O count provides substantial board-level connectivity, while 3,072 logic cells can implement control logic, state machines, interfaces, and parallel data-processing functions in one programmable device.
Designers should verify the exact I/O standards, supported clocking resources, available PLL and memory resources, power requirements, and programming configuration in the Microchip A3P125 documentation. PCB design must follow the 208-pin package drawing, provide clean power and ground distribution, and reserve programming and configuration resources for the intended toolchain and system architecture.
This product overview combines the manufacturer specifications, package information, logic-capacity details, migration guidance, application analysis, and drop-in ordering alternatives into a design-focused reference. It also highlights verification points that engineers should check before reusing an existing 208-pin ProASIC3 PCB or transferring a design from a larger device.
直接替換替代品,適用於 A3P125-PQ208I — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: A3P125-PQ208I (相同外形與佔位) — 差異在於 Package Dimensions, Package Type, Configuration Memory, Metal Layers, Process Technology.
A3P125-PQ208
✅ 直接替換聯絡詢價
查看資料表 →A3P125-PQG208
✅ 直接替換📋 參考替代品(不在目錄中)
A3P125-PQG208I
✅ 直接替換📋 參考替代品(不在目錄中)
A3P125-PQ208IY
✅ 直接替換📋 參考替代品(不在目錄中)
A3P125-PQ208YI
✅ 直接替換📋 參考替代品(不在目錄中)
A3P125-PQ208I 最大額定值與電氣特性
| Product Type | ProASIC3 flash-based field-programmable gate array |
| System Gates | 125,000 gates |
| Logic Cells / Logic Blocks | 3,072 logic cells |
| Internal SRAM | 36,864 bits |
| User I/O Count | 133 I/Os |
| Logic Family | CMOS |
| Configuration Technology | Nonvolatile flash |
| Process Technology | 130 nm CMOS |
| Metal Layers | 7 layers, including 6 copper layers |
| Package Type | 208-BFQFP plastic QFP |
| Package Dimensions | 28 mm x 28 mm |
| Package Height | 3.40 mm |
| Terminal Pitch | 0.50 mm |
| Total Pins | 208 pins |
| 安裝類型 | Surface mount |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
A3P125-PQ208I 3.40 mm 腳位配置指南
A3P125-PQ208I(3.40 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: A3P125-PQ208I.
請參閱 資料表 以查看完整腳位配置。
典型應用
A3P125-PQ208I 適用於 6 應用s: Industrial Automation and PLC Control, Communications Protocol Consolidation, Test and Measurement Instrumentation, ASIC Replacement and Design Consolidation, Embedded Protocol and Interface Bridge, Aerospace and Defense Control Logic.
Industrial Automation and PLC Control
The A3P125-PQ208I fits programmable industrial controllers because its 3,072 logic cells can implement sequencing, state machines, interlocks, and communication logic while 133 I/Os connect field inputs and outputs. The flash-based ProASIC3 architecture retains its configuration after power cycling, supporting deterministic startup without a separate configuration PROM. Its 208-pin BFQFP also provides enough physical connectivity for multiple buses, discrete sensors, actuator drivers, and status indicators. Before release, verify the industrial temperature grade, logic levels, I/O tolerances, timing constraints, and isolation requirements against the equipment specification.
推薦
Communications Protocol Consolidation
The A3P125-PQ208I can consolidate parallel interface logic, packet framing, buffering, and protocol state machines in a single programmable device. Its 125,000 system gates and 36,864 internal SRAM bits are useful for designs that require more combinational logic and board-level connectivity than a small microcontroller provides, without moving to a larger FPGA. Use the available I/Os for synchronous and asynchronous interface signals, and select I/O standards supported by the exact device. Timing closure, clock-domain relationships, serial interfaces, and available PLL resources must be confirmed before assigning the device.
推薦
Test and Measurement Instrumentation
In instrumentation, the A3P125-PQ208I can implement acquisition sequencing, trigger logic, digital calibration, and control functions while its 133 I/Os connect sensors, ADC interfaces, relay drivers, and displays. The nonvolatile flash configuration supports repeatable field operation, while the 3,072 logic cells allow parallel datapath and control functions to share one FPGA. Designers should use the manufacturer timing and power guidance to define clock constraints, I/O voltage, termination, and drive strength. Signal-integrity planning is especially important when the device interfaces with high-speed analog-to-digital converters or long external buses.
推薦
ASIC Replacement and Design Consolidation
The A3P125-PQ208I is appropriate for low-to-medium-volume logic consolidation where an ASIC-like fixed function can instead be implemented in reprogrammable flash-based logic. Its 3,072 logic cells and 125,000 system gates support control paths, datapaths, and board interfaces in one package, while 36,864 internal SRAM bits provide local storage for buffers and state. The device can also support design evolution because stored configurations may be revised during qualification or production. Engineering should validate timing closure, resource utilization, pin assignments, configuration security, and any software or firmware dependencies before committing to a production release.
推薦
Embedded Protocol and Interface Bridge
The A3P125-PQ208I can serve as a bridge between legacy parallel interfaces and newer serial or mixed-signal systems because it combines substantial programmable logic with 133 user I/Os. Examples include translating bus formats, buffering asynchronous data, generating control strobes, and implementing test or fault logic around an existing processor. The 36,864-bit internal SRAM allows local FIFO-like structures where required, although the actual usable memory organization must be checked in the device documentation. Pin reassignment, I/O standard support, clock-domain crossing, and asynchronous timing constraints are the principal checks before using this device as a drop-in logic companion.
推薦
Aerospace and Defense Control Logic
The A3P125 family is suitable for evaluating nonvolatile FPGA logic in control, sequencing, and interface applications where programmable updates and a substantial number of I/Os are useful. The A3P125-PQ208I provides 3,072 logic cells, 125,000 system gates, and 133 user I/Os for integrating command decoding, telemetry handling, or redundant monitoring functions. Flash-based configuration enables the stored logic to remain available after power loss. Qualification for an aerospace program cannot be inferred from the base ordering code alone: designers must confirm the exact temperature grade, screening, radiation, reliability, export-control, and long-term availability requirements with the manufacturer.
推薦
推薦產品摘要
工程參考資料,適用於 A3P125-PQ208I — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | A3P125-PQ208 | A3P125-PQG208 | A3P125-PQG208I | A3P125-PQ208IY | A3P125-PQ208YI |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 208-BFQFP | 208-BFQFP | 208-BFQFP | 208-BFQFP | 208-BFQFP | 208-BFQFP |
| System Gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates |
| Logic Cells / Logic Blocks | 3,072 logic cells | 3,072 logic cells | 3,072 logic cells | 3,072 logic cells | 3,072 logic cells | 3,072 logic cells |
| Configuration Technology | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash |
| Package Dimensions | 28 mm x 28 mm, 0.50 mm pitch | 28 mm x 28 mm, 0.50 mm pitch | 28 mm x 28 mm, 0.50 mm pitch | 28 mm x 28 mm, 0.50 mm pitch | 28 mm x 28 mm, 0.50 mm pitch | 28 mm x 28 mm, 0.50 mm pitch |
主要差異化特點
- Exact 125,000-gate ProASIC3 resource configuration (對比A3P125-PQ208)
- Industrial I ordering designation with an active commercial listing (對比A3P125-PQG208I)
- Nonvolatile flash configuration in a 208-pin surface-mount package (對比A3P125-PQ208YI)
- 133 user I/Os support high board-level connectivity (對比A3P125-PQ208IY)
設計說明
Treat the A3P125-PQ208I as a fine-pitch 208-pin QFP rather than a generic 208-pin footprint. Use the manufacturer package drawing to define pad dimensions, solder-mask clearance, and paste apertures for the 0.50 mm pitch. Confirm courtyard, thermal relief, and assembly tolerances against the PCB fabricator's capability. Signal and power assignments should come directly from the A3P125 package documentation because ordering-code differences do not by themselves guarantee identical pin functions.
Plan the power tree before layout by assigning core and I/O supply domains from the exact device documentation. Decoupling should follow the capacitance, voltage, and ESR guidance associated with the selected supply rails, with short connections and adequate ground reference. Because the public product overview does not state maximum current, static power, or dynamic power, determine those limits from Microchip's power guidance and include startup, I/O-load, and clocking scenarios in the budget.
Assign clocks and high-speed interfaces only after checking the A3P125's supported I/O standards and timing constraints. Keep clock traces short, provide a continuous ground reference, and use the device's recommended input, output, and termination techniques. For migrated designs, compare pin functions and edge relationships rather than relying only on package dimensions; a matching footprint does not guarantee that a clock, configuration pin, or voltage-sensitive I/O can be connected identically.
Do not substitute an A3P125 ordering code solely because it also contains 208 pins. Confirm the exact ordering information, temperature grade, qualification status, device marking, lifecycle status, and configuration compatibility for every alternative. Microchip's A3P250 migration note supports pin-compatibility analysis within the ProASIC3 family, but it still requires design-level timing, resource, and I/O verification. A related PQG208I record is identified as discontinued, so procurement planning must use the full suffix.
合規資訊
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ordering code. Confirm environmental and qualification status with Microchip Technology using the complete MPN.