AD532JHZ - 4-Quadrant Analog Multiplier | Analog Devices
MPN: AD532JHZ ✗ 停產AD532JHZ 概覽
An integrated circuit analog multiplier is a precision signal-processing component that multiplies two input voltages and produces an output proportional to their product. When used in a feedback arrangement with an analog divider, it can also perform division, squaring, root extraction, modulation, demodulation, and signal generation. The AD532 belongs to the broader analog multiplier and divider hierarchy within analog integrated circuits, where precision linear signal processing complements general-purpose amplifier functions.
The AD532JHZ combines four-quadrant operation with internal calibration. Four-quadrant capability means the product output can change polarity as either input crosses zero, a requirement for many modulation and control systems. Internal trimming reduces assembly complexity by eliminating external adjustment networks while preserving the factory-calibrated characteristics of the monolithic device. Its dual ±15 V supply also provides sufficient headroom for bipolar analog signals commonly encountered in laboratory and industrial control equipment.
The AD532 is specified at 25 °C with ±15 V supply rails and a minimum load resistance of 2 kΩ. These conditions are important when evaluating signal loading, output range, and accuracy because performance and usable output swing depend on the circuit configuration. The device is intended for precision multiplier and divider circuits, including analog control loops, measurement bridges, instrumentation channels, and modulation systems.
Typical uses include analog computation modules, laboratory measurement systems, industrial process-control equipment, and communication-signal processing. In each case, the AD532JHZ can implement multiplication directly and division through a closed-loop arrangement. Designers should account for supply polarity, input and output signal ranges, load impedance, grounding, and frequency-dependent accuracy when planning the surrounding analog network.
A primary design consideration is preserving the common reference and feedback-node behavior of the multiplier circuit. Incorrect grounding, inadequate return paths, or loading that violates the minimum 2 kΩ load condition can degrade performance. The 10-pin TO-100 package also requires adequate clearance and suitable thermal management because a through-hole package can be exposed to elevated internal temperature at sustained high dissipation.
This page combines manufacturer product information, technical search results, package details, lifecycle status, pricing evidence, and practical selection guidance. It also distinguishes genuine pin-compatible AD532 family alternatives from broader analog multipliers that may offer similar functions but cannot be assumed to share the same footprint or pinout.
直接替換替代品,適用於 AD532JHZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD532JHZ (相同外形與佔位) — 差異在於 Package, Product Type.
AD532KHZ
✅ 直接替換聯絡詢價
查看資料表 →AD532SH
✅ 直接替換聯絡詢價
查看資料表 →AD532KH
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD532JHZ 最大額定值與電氣特性
| Product Type | Internally trimmed integrated circuit multiplier |
| Multiplier Function | Four-quadrant analog multiplication |
| Divider Capability | Supported by analog feedback configuration |
| 供應電壓 | ±15 V |
| Specified Temperature | 25 °C |
| Minimum Load Resistance | 2 kΩ |
| Offset Voltage Configuration | Grounded unless otherwise noted |
| 封裝 | 10-pin TO-100 |
| Package Type | TO-100-10 |
| 安裝類型 | Through-hole |
| Packaging | Tube |
| Trim Method | Internal trimming |
| Device Class | Analog multiplier/divider IC |
| Product Status | Not recommended for new designs |
AD532JHZ to-100-10 腳位配置指南
AD532JHZ(to-100-10 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD532JHZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD532JHZ 適用於 6 應用s: Precision Analog Computation, Analog Divider Circuits, Instrumentation Signal Processing, Industrial Process Control, Modulation and Demodulation, Legacy Equipment Repair.
Precision Analog Computation
The AD532JHZ is suitable for analog computation modules that require the product of two bipolar input signals. Its four-quadrant operation allows the output polarity to follow the signs of both inputs, while internal trimming eliminates external calibration networks that would otherwise add components and adjustment effort. In a suitable feedback and reference network, the multiplier core provides a compact way to implement multiplication, scaling, and related control equations. The specified ±15 V supplies support traditional bipolar signal ranges, and the manufacturer lists a minimum load resistance of 2 kΩ. Designers should preserve that loading condition and establish an appropriate analog ground reference before the circuit is evaluated for accuracy.
推薦
Analog Divider Circuits
The AD532JHZ can support divider and ratio-computation circuits when placed in an appropriate analog feedback arrangement. Its internally trimmed multiplier element reduces the number of external adjustment components compared with modular implementations, while four-quadrant behavior accommodates signals that change polarity. This makes the device useful in control and measurement systems where a denominator or reference signal varies dynamically. Application design must include the AD532 data sheet’s reference-network requirements, minimum 2 kΩ load condition, and ±15 V reference specification conditions. Stable feedback layout and grounded offset inputs are particularly important because parasitic resistance and high-impedance nodes can introduce errors in division ratios.
推薦
Instrumentation Signal Processing
The AD532JHZ fits laboratory and industrial instrumentation blocks that must multiply a measured signal by a scale factor, coefficient, or control variable. The monolithic, internally trimmed construction simplifies procurement of one calibrated multiplier rather than a modular assembly with several external trimmers. Four-quadrant operation is useful for bipolar sensor outputs and phase-sensitive measurements where the two inputs can have either polarity. The 10-pin TO-100 package provides through-hole assembly and adequate spacing for hand installation in legacy instruments. Engineers should pay attention to grounding, resistor accuracy, input levels, output loading, and thermal rise so that system error is dominated by the external precision components rather than layout noise.
推薦
Industrial Process Control
The AD532JHZ can be used in legacy process-control systems to calculate proportional products or implement feedback-controlled analog functions. Its four-quadrant behavior permits positive and negative process-error signals without switching the multiplier’s operating polarity manually. Internal trimming is particularly valuable in industrial equipment because it reduces external calibration hardware and assembly variation. The specified ±15 V dual supply aligns with conventional industrial analog signal-chain practices, although the circuit must observe the data sheet’s minimum 2 kΩ load requirement. For new installations, evaluate current-recommended precision analog products because the AD532 family is not recommended for new designs; for maintenance of existing equipment, exact ordering-code verification is essential.
推薦
Modulation and Demodulation
The AD532JHZ is suitable for product-modulation stages in bipolar signal-processing systems. Multiplying a message signal by a sinusoidal or switching reference produces a modulated product, while four-quadrant operation supports references and message signals with changing polarity. Its internally trimmed multiplier provides a compact monolithic implementation for laboratory transmitters, educational equipment, and legacy communications apparatus. The designer must keep signal amplitudes within the device’s operating limits and account for the minimum 2 kΩ load requirement at the output. PCB or chassis layout should minimize loop area around the multiplier, reference source, and feedback components because stray capacitance can affect modulation bandwidth and unwanted spectral products.
推薦
Legacy Equipment Repair
The AD532JHZ is primarily valuable for repairing or maintaining vintage analog instruments, laboratory equipment, and industrial controllers that already use the AD532 family. Because the part is supplied in a 10-pin TO-100 package and described as internally trimmed, an exact-ordering-code replacement can preserve the original circuit architecture when its specifications match. Technicians should compare the manufacturer ordering table, pin diagram, temperature grade, and operating conditions before installation. The component is not recommended for new designs, so long-term continuity planning should include lifecycle monitoring and an evaluation of currently recommended precision multiplier products. This page’s Request a Quote form is the appropriate route for current AD532JHZ supply and lead-time information.
推薦
推薦產品摘要
工程參考資料,適用於 AD532JHZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD532KHZ | AD532SH | AD532KH | AD532JH |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 |
| Function | Four-quadrant analog multiplier/divider IC | Four-quadrant analog multiplier/divider IC | Four-quadrant analog multiplier/divider IC | Four-quadrant analog multiplier/divider IC | Four-quadrant analog multiplier/divider IC |
| Temperature Grade | AD532JHZ ordering grade | AD532KHZ ordering grade | AD532SH ordering grade | AD532KH ordering grade | AD532JH ordering grade |
主要差異化特點
- Pin-compatible AD532 family maintenance path (對比AD532KHZ)
- Internal trimming reduces external adjustment (對比AD532SH)
- Four-quadrant bipolar multiplication in a through-hole package (對比AD532JH)
設計說明
Do not assume that any 10-pin multiplier is interchangeable with the AD532JHZ. Use the manufacturer pin-configuration drawing to verify signal inputs, reference terminals, offset-voltage grounding, and supply connections. The minimum load resistance is 2 kΩ under the stated specification conditions, so output buffers may be needed when the surrounding circuit presents a lower impedance.
Keep the multiplier’s reference and feedback components close to their associated terminals and use a low-impedance analog ground return. High-impedance nodes around the multiplier can pick up noise and introduce ratio errors, particularly in division and modulation circuits. Arrange input, feedback, and output paths to avoid crossing sensitive nodes and maintain a compact ground loop beneath the analog section.
The TO-100 package provides through-hole spacing but does not eliminate thermal-rise concerns. Check dissipation under the actual input, output, and feedback-network conditions, and provide copper area or a suitable heat path when operating continuously at elevated dissipation. Verify that airflow and enclosure temperature remain compatible with the selected ordering grade and the manufacturer’s operating-temperature limits.
合規資訊
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements were identified. AEC-Q100 is not applicable because the AD532 is a general-purpose analog multiplier rather than an automotive-qualified device.