AD532KHZ - 4-Bit, 1 MHz Analog Multiplier | Analog Devices
MPN: AD532KHZ ✗ 停產AD532KHZ 概覽
An analog multiplier is a specialized amplifier or integrated circuit that produces an output proportional to the product of two input voltages. Its functional hierarchy extends from analog multiplier to analog computing IC, signal-processing IC, and integrated circuit. A divider operation can be implemented by placing a resistor in the feedback path of the multiplier, allowing one input to establish a scaling ratio while the other supplies the signal being scaled.
The AD532KHZ combines a 4-bit resolution classification with 1 MHz bandwidth and internal trimming. Internal trimming reduces the need for external calibration of multiplier accuracy, while the hermetic TO-100-10 package supports operation in demanding industrial and legacy instrumentation environments. Its primary electrical characteristics are specified in the Analog Devices manufacturer datasheet, including gain accuracy, linearity, bandwidth, supply requirements, input ranges, and temperature behavior.
Analog Devices identifies AD532 as not recommended for new designs, so the part should be selected primarily for repair, continuation, or redesign of an existing AD532-based circuit. Hermetic packaging and stable multiplication characteristics remain valuable where an established circuit footprint, test methodology, or qualified supply chain is required. Before replacing the device, verify the original grade suffix, operating temperature range, supply voltage, pin orientation, and external resistor network.
Typical uses include four-quadrant multipliers in analog control loops, precision dividers in feedback networks, amplitude-control circuits, synchronous demodulation stages, and laboratory instrumentation. The 1 MHz bandwidth supports signal chains operating well above audio frequency, although practical system bandwidth also depends on the external resistor network, source impedance, load, and compensation or trimming components.
The primary design consideration is to reproduce the original application circuit rather than redesign around generic equations. Maintain the manufacturer-specified bypass capacitors, resistor tolerances, pin connections, and grounding arrangement. The TO-100 package requires adequate lead-bend clearance and PCB spacing, and its thermal performance depends on the board-level copper area and airflow.
This page combines the device identity, package information, lifecycle status, verified source links, drop-in candidates, and engineering guidance needed to evaluate the AD532KHZ for maintenance and controlled redesign applications.
直接替換替代品,適用於 AD532KHZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD532KHZ (相同外形與佔位) — 差異在於 Package, Product Type.
AD532JHZ
✅ 直接替換聯絡詢價
查看資料表 →AD532SH/883B
✅ 直接替換📋 參考替代品(不在目錄中)
AD532JNZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD532KNZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD532KHZ 最大額定值與電氣特性
| Product Type | Analog multiplier/divider IC |
| Multiplier Architecture | 4-quadrant |
| Resolution Classification | 4 bit |
| Bandwidth | 1 MHz |
| Trim Type | Internally trimmed |
| 封裝 | 10-pin TO-100 hermetically sealed metal can |
| Total Pin Count | 10 pins |
| 安裝類型 | Through-hole |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| Lifecycle Recommendation | Not recommended for new designs |
AD532KHZ 10-pin to-100 hermetically sealed metal can 腳位配置指南
AD532KHZ(10-pin to-100 hermetically sealed metal can 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD532KHZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD532KHZ 適用於 6 應用s: Four-Quadrant Analog Control, Precision Analog Divider, Amplitude and Gain Control, Synchronous Demodulation, Laboratory Instrumentation, Legacy Equipment Maintenance.
Four-Quadrant Analog Control
The AD532KHZ is appropriate for four-quadrant control because its 1 MHz bandwidth permits operation above baseband audio frequencies while supporting input combinations of either polarity. The multiplier can form the nonlinear product term required in analog computation, loop compensation, and plant-modeling circuits. Preserve the manufacturer reference network and external resistor accuracy because the device's multiplication error, common-mode range, and output swing determine usable control accuracy. The hermetic TO-100-10 package also fits legacy control assemblies where an established mechanical footprint and circuit-board spacing are already present.
推薦
Precision Analog Divider
AD532KHZ can implement an analog divider when one input is connected to a precision reference and the other is routed through the appropriate feedback arrangement. Its 4-quadrant multiplier core provides consistent behavior across signal polarities, while the 1 MHz bandwidth leaves useful margin for control and instrumentation bandwidths below that limit. Divider accuracy depends on the external resistor network as well as the IC, so use the manufacturer reference values and confirm thermal drift, common-mode headroom, and output loading before assigning a system accuracy target.
推薦
Amplitude and Gain Control
The AD532KHZ fits amplitude-control and programmable-gain analog blocks because multiplying a signal by a controlled reference produces the required scaled output. Its 1 MHz bandwidth supports modulation, servo, and instrumentation loops beyond audio-bandwidth requirements. In an implementation, the gain-control reference should remain within the specified input range and exhibit low noise and stable temperature behavior. External resistor matching and trimming directly affect multiplier accuracy, so production designs should preserve the reference layout and account for excitation-level changes when determining linearity across the operating range.
推薦
Synchronous Demodulation
AD532KHZ can serve as the multiplication element in a synchronous-demodulation chain, where a carrier or reference is multiplied by the incoming modulated signal. The 1 MHz bandwidth is sufficient for many low-frequency instrumentation and communications control paths, and the four-quadrant capability allows bipolar reference and signal combinations. Practical demodulator performance depends on input amplitude, common-mode limits, filter design, and phase accuracy. Place the subsequent filter according to the manufacturer application guidance and use a stable reference source to avoid adding amplitude noise or drift to the recovered baseband signal.
推薦
Laboratory Instrumentation
The AD532KHZ is useful in legacy laboratory instruments that require analog multiplication for calibration, ratio measurement, signal generation, or closed-loop control. Its 1 MHz bandwidth covers precision audio, low-frequency communications, and industrial test functions, while the hermetic TO-100-10 package supports established instrument designs. The internal trim reduces external calibration complexity, but accuracy still depends on the reference resistors, excitation stability, and output measurement method. For instrument redesign, reproduce the original pin connection and component layout and confirm that the selected grade satisfies the enclosure's temperature and reliability requirements.
推薦
Legacy Equipment Maintenance
The AD532KHZ is particularly relevant to maintenance of legacy analog equipment because the TO-100-10 package, 4-quadrant operation, and 1 MHz bandwidth define a recognizable functional role in multiplier-based circuits. Analog Devices marks AD532 as not recommended for new designs, making replacement continuity more defensible than adopting an unverified modern substitute. During board repair, check all supply pins and signal inputs against the manufacturer pin table, preserve bypass routing, and compare the installed suffix with the replacement grade. If a documented same-package option is used, verify temperature range and qualification rather than relying on package shape alone.
推薦
推薦產品摘要
工程參考資料,適用於 AD532KHZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD532JHZ | AD532SH/883B | AD532JNZ | AD532KNZ | AD532JH |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 |
| Product Type | Analog multiplier/divider | Analog multiplier/divider | Analog multiplier/divider | Analog multiplier/divider | Analog multiplier/divider | Analog multiplier/divider |
| Multiplier Architecture | 4-quadrant | 4-quadrant | 4-quadrant | 4-quadrant | 4-quadrant | 4-quadrant |
| Bandwidth | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz |
| Resolution Classification | 4 bit | 4 bit | 4 bit | 4 bit | 4 bit | 4 bit |
| Trim Type | Internally trimmed | Internally trimmed | Internally trimmed | Internally trimmed | Internally trimmed | Internally trimmed |
主要差異化特點
- Documented complete replacement path (對比AD532JHZ)
- Screened high-reliability option (對比AD532SH/883B)
- Established 4-quadrant performance class (對比AD532JH)
設計說明
Reproduce the original TO-100-10 footprint, pin-1 orientation, and lead spacing before upgrading a legacy board. Keep the external multiplier and feedback components close to the relevant pins, use the manufacturer reference resistor values and tolerances, and retain short, low-loop-area routing around the analog inputs. Because the package has ten leads, verify every connection against the AD532 manufacturer pin-description table rather than relying on a generic TO-100 drawing.
Do not interpret the 4-bit classification as a digital data converter. The AD532KHZ is an analog multiplier whose accuracy is governed by gain error, nonlinearity, common-mode range, output swing, external resistor ratios, and signal amplitude. Likewise, the 1 MHz bandwidth does not guarantee usable accuracy at every frequency or output level. Reproduce the manufacturer's typical application circuit, preserve its trimming arrangement, and verify excitation and load conditions before declaring the replacement electrically equivalent.
Identify all supply and ground connections from the manufacturer datasheet and measure them before inserting AD532KHZ. Place bypass capacitors adjacent to the intended supply pins and maintain a low-impedance return path, since supply disturbances can appear in the multiplied output. Do not infer the supply voltage from generic multiplier documentation; check the exact AD532 grade and manufacturer absolute-maximum table before energizing a board.
The hermetic TO-100 package can dissipate heat from internal bias circuitry and from signal-dependent output loading. In a sealed instrument, provide airflow or copper area appropriate for the measured dissipation and avoid mounting the device against a heat-insulating panel. For new thermal calculations, record ambient temperature, package dissipation, and board construction first, then use the manufacturer's thermal information rather than estimating junction temperature from the package name alone.
Keep both multiplier inputs within their specified common-mode range and provide low source impedance to limit gain errors at the 1 MHz bandwidth limit. Terminate unused inputs according to the manufacturer guidance, and avoid long parallel traces that can couple the multiplication channels. If the application includes demodulation or precision gain control, use a clean reference source and account for amplitude, phase, and filter behavior across the complete signal bandwidth.
合規資訊
The AD532 family is an older analog multiplier/divider and the product page states that AD532 is not recommended for new designs. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified for AD532KHZ.