AD534LHZ - Precision 4-Quadrant Multiplier | Analog Devices
MPN: AD534LHZ ✓ 啟用中AD534LHZ 概覽
An analog multiplier/divider belongs to the precision signal-processing IC hierarchy, where it combines with operational amplifiers, references, and data-conversion devices to implement control, measurement, modulation, and signal-conditioning functions. Unlike a digital multiplier, the AD534LHZ operates directly on continuous analog waveforms without requiring conversion, serialization, or arithmetic processing. This makes it useful when bandwidth, signal phase, and low added noise matter more than programmability.
The AD534 uses laser trimming to establish accurate scale-factor and symmetry characteristics. Analog Devices describes the product as a low-noise monolithic construction with 90 µV rms noise from 10 Hz to 10 kHz. Its four-quadrant operation allows either input polarity combination, supporting multiplication, division, RMS-related functions, modulation, and feedback-control applications. The manufacturer identifies the AD534 family as production devices, with the AD534LHZ offered in a 10-pin TO-100 package and tube packing.
Technical performance depends on signal amplitude, frequency, supply voltage, load, external compensation, and the configuration of the surrounding operational amplifiers. Because the multiplier operates over a broad ±22 V supply range, its internal dynamic range and output behavior require careful reference selection and gain planning. For highest accuracy, designers should use stable reference and feedback networks, maintain appropriate input and output signal levels, and account for temperature drift when setting system calibration limits.
Typical uses include precision closed-loop control, analog computation, instrumentation, programmable gain and signal conditioning, modulation, and measurement systems. The AD534LHZ can also support laboratory reference designs where a fixed four-quadrant multiplier is preferable to a digitally controlled multiplier. In industrial equipment, the wide temperature range can be valuable when the analog signal path must remain close to the sensing or actuation stage.
The principal layout concern is sensitive analog routing. Keep multiplier inputs and feedback nodes away from switching-power nodes, use short grounded guarding around high-impedance inputs, and provide a stable low-noise supply. Check the complete manufacturer datasheet for pin functions, recommended application circuits, compensation values, and operating limits before fixing the PCB layout.
This page combines package, temperature, electrical, sourcing, and application guidance with same-family drop-in alternatives, a parameter comparison, and practical design notes. It helps engineers identify the correct AD534 package option and plan a precision analog signal chain without conflating temperature-grade differences with functional compatibility.
直接替換替代品,適用於 AD534LHZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD534LH
✅ 直接替換📋 參考替代品(不在目錄中)
AD534SH
✅ 直接替換聯絡詢價
查看資料表 →AD534TH
✅ 直接替換聯絡詢價
查看資料表 →AD534JH
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD534KH
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD534LHZ 最大額定值與電氣特性
| Product Type | Four-quadrant analog multiplier/divider |
| Architecture | Monolithic, laser-trimmed |
| 工作電源電壓 | 22 V maximum |
| 輸出雜訊 | 90 µV rms from 10 Hz to 10 kHz |
| Minimum Operating Temperature | -55 °C |
| Maximum Operating Temperature | +125 °C |
| Power Dissipation | 500 mW maximum |
| Package Type | TO-100-10 |
| Package Dimensions | 9.4 mm length × 9.4 mm width × 4.7 mm height maximum |
| 安裝方式 | Through-hole |
| 腳位數 | 10 pins |
| Factory Pack Quantity | 100 units |
| Unit Weight | 1 oz maximum |
| RoHS 狀態 | RoHS/N |
| Trim Method | Laser trim |
| Signal Operation | Four-quadrant multiplication and division |
AD534LHZ 9.4 mm length × 9.4 mm width × 4.7 mm height maximum 腳位配置指南
AD534LHZ(9.4 mm length × 9.4 mm width × 4.7 mm height maximum 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD534LHZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD534LHZ 適用於 6 應用s: Precision Analog Control Loops, Instrumentation Signal Conditioning, Analog Computation Modules, Programmable Gain and Scaling Circuits, Modulation and Control Signal Generation, Laboratory and Low-Frequency Reference Designs.
Precision Analog Control Loops
The AD534LHZ fits closed-loop analog control because its four-quadrant multiplication supports products and ratios of positive or negative control signals. With a 22 V maximum operating supply and laser-trimmed construction, it can form the nonlinear control element in systems where discrete multipliers or digital calculations would add complexity. Designers should preserve the device's common-mode range, reference stability, and frequency-dependent accuracy by following the manufacturer's application circuit. External operational amplifiers should provide adequate loop gain and output swing, while compensation must be checked with the intended feedback network. The TO-100-10 package supports through-hole placement and conventional thermal analysis in laboratory, industrial, and instrumentation equipment.
推薦
Instrumentation Signal Conditioning
The AD534LHZ is well suited to instrumentation that must scale or divide continuously varying sensor signals. Four-quadrant operation accommodates polarity changes, while the 90 µV rms noise specification from 10 Hz to 10 kHz helps preserve the integrity of low-level measurements. The multiplier can be placed within a feedback network to implement gain control, normalization, or ratio measurement. Reference accuracy, input bias current, and resistor tracking determine much of the final system error, so stable references and matched networks remain essential. Its -55 °C to +125 °C operating range also supports wide environmental deployments when the surrounding analog components are selected for the same environment.
推薦
Analog Computation Modules
The AD534LHZ enables compact analog computation because it performs multiplication or division directly in the analog domain. This avoids a digital sampling chain when the result must remain continuous or must preserve phase relationships. Typical functions include squaring, RMS approximation, variable-gain stages, and error-correction terms in feedback systems. The 22 V maximum supply supports conventional laboratory rails, but usable signal amplitude is limited by internal headroom and the chosen reference. Place input and feedback components close to the device, maintain a quiet ground reference, and verify closed-loop stability over the full intended frequency range. The package's thermal rating should be considered when operating near sustained maximum power.
推薦
Programmable Gain and Scaling Circuits
The AD534LHZ can form the active element of an analog scaling stage where a control voltage or signal must multiply another signal. Its four-quadrant behavior permits positive and negative control values, making it useful for bidirectional actuator command and measurement systems. The low-noise, laser-trimmed construction supports precision scaling better than simple passive networks, although overall accuracy remains dependent on reference quality and resistor accuracy. Keep the scaling reference on a low-impedance, decoupled node and route the multiplier input away from high-current switching paths. Designers should also evaluate bandwidth because compensation capacitors and parasitic capacitance can influence closed-loop response and stable gain.
推薦
Modulation and Control Signal Generation
The AD534LHZ is applicable to analog modulation and control-signal generation because multiplication combines two independent waveforms without requiring a digital mixer. The resulting product can support amplitude control, phase-sensitive detection, synchronous demodulation, and compensating control functions. Its 90 µV rms noise over 10 Hz to 10 kHz provides a useful baseline when designing low-noise modulation paths. Accurate results still depend on reference stability, input drive, and the bandwidth of the surrounding active devices. Maintain short, symmetrical analog routing, provide local supply bypassing, and avoid placing the multiplier input beside switching nodes. Confirm harmonic and distortion behavior in the completed circuit rather than relying only on the low-frequency noise figure.
推薦
Laboratory and Low-Frequency Reference Designs
The AD534LHZ is useful in laboratory multiplier boards, educational instruments, and low-frequency precision reference designs because it combines a fixed analog multiplier function with a conventional 10-pin TO-100-10 package. The manufacturer describes the device as internally trimmed, with excellent long-term stability and monolithic construction. This makes it convenient for repeatable analog computations without the control overhead of a programmable multiplier IC. Designers should preserve clean supplies, use a stable reference, and include provisions for calibration where system accuracy requires it. The through-hole package also simplifies prototype rework, although the metal-case connection and thermal path must be implemented according to the package drawing and recommended circuit.
推薦
推薦產品摘要
工程參考資料,適用於 AD534LHZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD534LH | AD534SH | AD534TH | AD534JH | AD534KH |
|---|---|---|---|---|---|---|
| Package | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 | TO-100-10 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Function | Four-quadrant analog multiplier/divider | Four-quadrant analog multiplier/divider | Four-quadrant analog multiplier/divider | Four-quadrant analog multiplier/divider | Four-quadrant analog multiplier/divider | Four-quadrant analog multiplier/divider |
| Trim Method | Laser trim | Laser trim | Laser trim | Laser trim | Laser trim | Laser trim |
主要差異化特點
- Four-quadrant analog operation without digital conversion (對比AD534SH)
- Wide environmental operating range (對比AD534LH)
- Laser-trimmed monolithic construction with low noise (對比AD534TH)
設計說明
Treat the AD534LHZ input, trim, and feedback nodes as high-impedance analog signals. Route them away from switching inductors, power-supply return currents, and digital clock traces. Use a continuous ground plane with the analog return path kept short, and place input and feedback components close to the relevant device pins. Keep the metal-case connection consistent with the manufacturer package drawing because the case may carry a functional connection rather than serving only as a thermal terminal.
The AD534LHZ is rated for a 22 V maximum operating supply and 500 mW maximum power dissipation in the cited package data. Do not infer safe dissipation from the supply rating alone; calculate actual device dissipation under the worst-case input, output, and load conditions. Use local supply bypassing with short return paths and verify that supply transients remain below the absolute maximum limits shown in the manufacturer datasheet.
Do not treat the LH, SH, TH, JH, and KH ordering suffixes as freely interchangeable without checking the AD534 selection table. Package equivalence establishes footprint compatibility, but grade, qualification, temperature, and packing requirements may differ. For an existing AD534LHZ board, verify the complete pin function, case connection, operating temperature, and production status of the proposed replacement before approving it as a drop-in substitution.
Accuracy in a multiplication or division circuit depends on reference stability, resistor matching, input drive, and frequency response as well as the multiplier itself. Start from the manufacturer application circuit, preserve recommended compensation values, and avoid changing feedback topology without checking closed-loop stability. For low-level signals, evaluate the 90 µV rms noise specification over the actual system bandwidth rather than assuming the 10 Hz to 10 kHz figure represents all operating frequencies.
合規資訊
RoHS/N status is identified in the AD534 family comparison information. Other environmental and material-compliance attributes are not stated on this page.