AD96687BR - 2.5 ns Dual ECL Comparator | Analog Devices
MPN: AD96687BR ✗ 停產AD96687BR 概覽
A voltage comparator is a semiconductor integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The AD96687 belongs to the comparator hierarchy within amplifier and interface ICs. Its ECL output structure supports very fast decision times while retaining the familiar emitter-coupled logic voltage convention used in demanding high-speed systems.
Principal advantages include the 2.5 ns propagation delay, 50 ps delay dispersion, and low power consumption of 118 mW per comparator. The open-emitter outputs provide flexible termination and wired-connection options, while the complementary outputs allow one package to provide both polarities of a threshold decision. The manufacturer identifies high-speed triggers, high-speed line receivers, and threshold detectors as principal uses for this comparator family.
The AD96685 and AD96687 share the same ultrafast ECL architecture. The AD96685 provides one comparator, while the AD96687 provides two independent comparators in one package. Propagation delay dispersion measures output-timing variation as overdrive changes; the 50 ps value helps designers evaluate timing consistency across a range of input overdrive conditions. Open-emitter outputs are intended for termination through 50 ohm resistors to -2.0 V or an equivalent ECL termination arrangement.
Typical applications include high-speed triggers, pulse-width and threshold detection circuits, high-speed line receivers, clock or pulse qualification, and instrumentation requiring nanosecond-scale decision-making. The dual configuration can reduce component count when a board requires two closely related comparison functions. Each output still requires correct power-supply decoupling and a suitable ECL termination network.
Layout is critical because propagation delays of 2.5 ns leave little margin for excessive trace length, impedance discontinuity, or reflection. The manufacturer recommends MicroStrip or Stripline techniques when ECL signals must travel more than a few centimeters. Keep comparator inputs and output termination paths short, use controlled-impedance routing where applicable, and account for the negative supply and ECL reference network in return-current planning.
This product page combines the manufacturer’s ordering guidance with a practical view of timing, termination, application selection, and design trade-offs. It also highlights the family distinction between the single AD96685 and dual AD96687, helping engineers evaluate whether one or two comparator channels are required before beginning layout work.
直接替換替代品,適用於 AD96687BR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD96687BRZ
✅ 直接替換📋 參考替代品(不在目錄中)
AD96687BR 最大額定值與電氣特性
| Comparator Type | Dual voltage comparator |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| Power Consumption | 118 mW per comparator |
| Logic Compatibility | ECL |
| 供應電壓 | -5.2 V |
| 輸出配置 | Complementary, latched, open-emitter |
| Number of Channels | 2 channels |
| Target Package | 16-lead SOIC |
| Family Package Options | DIP, SOIC, and PLCC |
| Recommended Output Termination | 50 ohm to -2.0 V or equivalent ECL termination |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
AD96687BR dip, soic, and plcc 腳位配置指南
AD96687BR(dip, soic, and plcc 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD96687BR.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD96687BR 適用於 6 應用s: High-Speed Trigger Circuits, High-Speed Line Receivers, Pulse-Width Threshold Detection, Clock and Pulse Qualification, Instrumentation Threshold Detectors, High-Speed Data Capture Qualification.
High-Speed Trigger Circuits
The AD96687BR fits high-speed trigger generation because each channel can make a comparison with a nominal 2.5 ns propagation delay. Two complementary channels can be used to define both sides of a threshold event without duplicating a single-channel package. The Analog Devices AD96685/AD96687 data sheet (Rev. D) identifies high-speed triggers as a primary application. Engineers should route both analog inputs symmetrically, terminate the open-emitter outputs with the specified ECL network, and keep the decision path short so propagation and reflection do not undermine edge timing.
推薦
High-Speed Line Receivers
The AD96687BR can support line-receiver functions where a received signal must be converted into a rapid logic decision. Its 2.5 ns propagation delay and 50 ps propagation delay dispersion are the central timing characteristics for this use. The manufacturer specifically lists high-speed line receivers as an application for the AD96685/AD96687 family. The open-emitter outputs require suitable ECL termination, and traces longer than a few centimeters may require MicroStrip or Stripline routing to preserve transition quality and limit ringing.
推薦
Pulse-Width Threshold Detection
The AD96687BR is suited to pulse-width and threshold detection because two comparator channels can monitor related edges with a nominal 2.5 ns response time. Complementary outputs also provide useful polarity options for downstream ECL logic. The manufacturer identifies threshold detection as an application for this family. For reliable measurements, the input network should present low, repeatable loading, the comparator supply should be properly decoupled, and the ECL outputs should use the prescribed termination to avoid false transitions caused by reflection.
推薦
Clock and Pulse Qualification
The AD96687BR can qualify clock or pulse signals in high-speed digital systems where a clean decision must occur in nanoseconds. Its 2.5 ns propagation delay provides a defined response interval, while 50 ps dispersion characterizes timing variation across different overdrive conditions. The dual complementary configuration is useful when both rising and falling thresholds or two related pulse conditions must be evaluated. Keep the source and reference paths short, maintain controlled return paths, and follow the manufacturer’s ECL termination recommendation to preserve edge fidelity.
推薦
Instrumentation Threshold Detectors
The AD96687BR is useful in instrumentation that requires rapid threshold decisions for sensor, test, or measurement signals. The dual architecture can compare two independent thresholds in a compact 16-lead SOIC, reducing the number of separate comparator packages. Its 2.5 ns delay is much shorter than the response time of many measurement systems, although the overall system result may be limited by noise, input bandwidth, and post-processing. Use symmetrical input routing, stable references, proper supply bypassing, and correctly terminated ECL outputs to avoid adding errors to the measurement chain.
推薦
High-Speed Data Capture Qualification
The AD96687BR can qualify captured data or control a fast sampling sequence when the system must recognize an input threshold with a nominal 2.5 ns delay. Two channels can monitor complementary limits or separate event conditions. This use requires careful attention to transmission-line effects because a fast comparator does not eliminate delays caused by long traces, mismatched terminations, or shared return-current paths. Follow the manufacturer’s guidance for MicroStrip or Stripline routing when ECL signals must extend beyond a few centimeters, and validate timing at the system level.
推薦
推薦產品摘要
工程參考資料,適用於 AD96687BR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD96687BRZ |
|---|---|---|
| Package | 16-lead SOIC | 16-lead SOIC |
| Brand | Analog Devices | Analog Devices |
| Comparator Configuration | Dual voltage comparator | Dual voltage comparator |
| Propagation Delay | 2.5 ns | 2.5 ns |
| Propagation Delay Dispersion | 50 ps | 50 ps |
| Power Consumption | 118 mW per comparator | 118 mW per comparator |
| Supply Voltage | -5.2 V | -5.2 V |
| Logic Compatibility | ECL | ECL |
| Output Configuration | Complementary, latched, open-emitter | Complementary, latched, open-emitter |
| Recommended Termination | 50 ohm to -2.0 V or equivalent ECL termination | 50 ohm to -2.0 V or equivalent ECL termination |
主要差異化特點
- Provides two high-speed comparison channels in one package (對比AD96685)
- Uses complementary latched open-emitter ECL outputs (對比AD96685)
- Maintains low propagation delay dispersion (對比AD96685)
設計說明
Keep the AD96687BR input and output paths short and use the specified 50 ohm ECL termination. The manufacturer recommends MicroStrip or Stripline techniques when signals must travel more than a few centimeters. Reflection caused by an incorrect termination can create false transitions and obscure the device’s nominal 2.5 ns decision time.
Route the two comparator channels symmetrically when they monitor related signals. Maintain a continuous return path beneath or adjacent to high-speed traces, decouple the -5.2 V supply close to the device, and avoid sharing narrow return-current paths between ECL outputs. These practices reduce coupling and ground bounce that can disturb threshold decisions.
Do not treat the 2.5 ns propagation delay as the complete system response time. Input-network delay, comparator overdrive, propagation delay dispersion, output rise and fall time, trace length, and termination all affect the observed edge position. Test the complete circuit with realistic input overdrive and verify timing at the receiving device.
Provide a stable -5.2 V supply and the manufacturer’s ECL termination arrangement. Place supply bypassing close to the package and check the supply for adequate current headroom and low transient noise. Because the open-emitter outputs are not intended to drive long unterminated routes, verify the complete output network before operation.
合規資訊
The manufacturer product page identifies AD96687 as not recommended for new designs. No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was identified for this ordering option.