ADS7254IPW - 12-Bit Dual 1-MSPS SAR ADC | Texas Instruments
MPN: ADS7254IPW ✓ 啟用中ADS7254IPW 概覽
An SAR analog-to-digital converter converts an analog input by repeatedly comparing the sampled voltage with a internally generated reference and adjusting a successive approximation. SAR ADCs occupy the ADC hierarchy alongside flash, pipeline, and delta-sigma converters. Compared with a pipeline ADC, the ADS7254IPW offers a compact dual-channel sampling architecture with simultaneous conversion, while its 12-bit resolution provides 4096 discrete codes for each input channel.
The main features include simultaneous sampling of two channels, fully differential inputs, and 1 MSPS conversion speed. Each channel includes an individually programmable reference source for calibration. The flexible serial interface allows the converter to operate across a wide power-supply range, making the device adaptable to industrial control, communications, and data-acquisition systems whose input circuitry requires precise channel-to-channel timing.
Simultaneous sampling is especially important when measuring phase, gain, or time-dependent relationships between two signals. Because both channels are sampled during the same conversion cycle, the ADS7254IPW avoids the timing offset that can occur when unrelated converters sample sequential channels. Its SAR architecture provides deterministic conversion behavior suitable for control loops and acquisition systems that require repeatable sampling, while the differential inputs support noise-controlled signal conditioning when paired with suitable drivers.
Typical uses include synchronized voltage and current measurement, motor and power-system monitoring, industrial sensor acquisition, communications equipment, and precision test and measurement instruments. The two-channel format is useful in systems that compare a sensed signal with a reference or monitor complementary quantities. Fully differential input architecture also makes the converter appropriate for balanced analog front ends where common-mode noise rejection and matched routing are important.
The primary design consideration is the analog input network. Each differential channel should use a driver and filtering arrangement that establishes the required common-mode voltage and bandwidth while preserving full-scale accuracy at 1 MSPS. Keep the two analog channels geometrically similar to minimize timing and gain differences, and follow the pin-description table in the manufacturer datasheet when assigning PCB signal and return paths.
This page combines the TI product description, family-level pin compatibility information, package details, structured alternatives, and practical application guidance. It also distinguishes verified family replacements from packaging-only orderable variants, helping engineers evaluate PCB reuse without confusing electrical compatibility with mechanical similarity.
直接替換替代品,適用於 ADS7254IPW — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADS7254IPW (相同外形與佔位) — 差異在於 Resolution.
ADS7854IPW
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ADS8354IPW
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADS7254IPW 最大額定值與電氣特性
| ADC Type | Successive-approximation register (SAR) ADC |
| 解析度 | 12 bit |
| Conversion Rate | 1 MSPS |
| Number of Channels | 2 channels |
| Sampling Type | Simultaneous sampling |
| Input Type | Fully differential |
| Number of Input Pairs | 2 differential input pairs |
| Programmable References | 2 individually programmable reference sources |
| Serial Interface | Flexible serial interface |
| 封裝 | 16-pin TSSOP |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
| Lead-Free Status | Lead-free |
ADS7254IPW 16-pin tssop 腳位配置指南
ADS7254IPW(16-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS7254IPW.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS7254IPW 適用於 6 應用s: Synchronized Voltage and Current Measurement, Industrial Sensor Acquisition, Motor Drive Feedback and Control, Communications and Baseband Signal Capture, Precision Test and Measurement, Power-System Monitoring.
Synchronized Voltage and Current Measurement
The ADS7254IPW is well suited to measuring a voltage signal and a current-derived signal at the same time because its two channels use a simultaneous-sampling architecture. At 1 MSPS, the converter can acquire up to one million 12-bit samples per second, giving a 12-bit measurement 4096 possible code levels. Place the two differential front ends symmetrically and use matched filtering where gain and timing matching are important. This arrangement reduces the channel skew that could otherwise corrupt calculated power, phase, or impedance because both analog values are captured during the same conversion sequence rather than by independently timed converters.
推薦
Industrial Sensor Acquisition
The ADS7254IPW can acquire two conditioned sensor outputs in industrial monitoring systems where compactness and synchronized sampling are important. Its fully differential inputs allow each sensor signal to be paired with a return or reference signal, helping the analog front end reject common-mode disturbances when the circuit is implemented correctly. The 12-bit resolution and 1 MSPS conversion capability provide a practical balance for process variables, position feedback, and equipment diagnostics. Keep the two input channels electrically similar, provide stable reference sources, and route sensitive analog signals away from digital clocks and switching power nodes to preserve measurement quality.
推薦
Motor Drive Feedback and Control
ADS7254IPW is appropriate for motor-control systems that need to monitor two related feedback quantities at a common instant. The simultaneous 1 MSPS conversion operation can capture current and voltage feedback without introducing the larger timing uncertainty associated with sequential sampling. Fully differential inputs fit current-shunt amplifiers and voltage-sense front ends that present balanced signals. Because the converter provides 12-bit resolution, designers should verify that quantization noise and analog-front-end gain remain acceptable over the control bandwidth. Place the ADC inputs close to the controlled signal sources and separate them from gate-drive and power-stage return currents.
推薦
Communications and Baseband Signal Capture
ADS7254IPW can serve as a dual-channel data-conversion element in communications equipment requiring deterministic, synchronized sampling. Two fully differential input paths support balanced receiver outputs, while the flexible serial interface allows the digital connection to operate over a wide power-supply range. At 1 MSPS and 12 bits, the device is suitable for envelope, power, or intermediate-frequency monitoring where fine resolution is not essential. Signal integrity depends on controlled input bandwidth, low-jitter clocking, and a quiet reference arrangement, so anti-alias filtering and return-path discipline remain necessary even though the converter uses a simultaneous dual-channel architecture.
推薦
Precision Test and Measurement
ADS7254IPW is useful in test equipment that compares two analog quantities, such as a measured node against a reference or a differential signal across a sensing element. Simultaneous sampling at 1 MSPS makes the dual 12-bit converter appropriate for repetitive measurements in which channel timing must remain repeatable. The two individually programmable references can support system-level gain calibration, while fully differential inputs encourage a balanced and noise-resistant measurement chain. To achieve useful precision, select amplifier and filter components for the target bandwidth, observe the manufacturer input and reference limits, and include calibration in the measurement procedure rather than relying on resolution alone.
推薦
Power-System Monitoring
The ADS7254IPW can monitor two power-system signals when the system requires coordinated rather than sequential observations. For example, one differential channel can measure a scaled voltage and another can monitor a scaled current or power-rail condition, with both sampled at 1 MSPS. The simultaneous architecture improves timing correlation for control and diagnostics. Its fully differential input architecture is compatible with balanced sensing networks, but input amplitude, common-mode range, and reference limits must remain within the manufacturer specifications. Keep the high-voltage or high-current sensing network isolated from the converter and use matched analog paths to minimize channel gain differences.
推薦
推薦產品摘要
工程參考資料,適用於 ADS7254IPW — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS7854IPW | ADS8354IPW |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Resolution | 12 bit | 14 bit | 16 bit |
| Conversion Rate | 1 MSPS | 1 MSPS | 700 kSPS |
| ADC Architecture | SAR ADC | SAR ADC | SAR ADC |
| Number of Channels | 2 channels | 2 channels | 2 channels |
| Sampling Mode | Simultaneous sampling | Simultaneous sampling | Simultaneous sampling |
| Input Type | Fully differential | Fully differential | Fully differential |
| Programmable Reference Sources | 2 individually programmable references | 2 individually programmable references | 2 individually programmable references |
主要差異化特點
- Retains the full 1 MSPS sampling rate while using a 12-bit conversion word (對比ADS8354IPW)
- Provides the lower-resolution option in the pin-compatible ADSxx54 family (對比ADS7854IPW)
- Combines two simultaneous channels with fully differential inputs (對比ADS8354IPW)
設計說明
Use the pin-description table in the ADSxx54 datasheet, Rev. B, to assign all 16 TSSOP connections. Place analog decoupling and input-conditioning components close to their associated pins, keep the two differential input paths geometrically similar, and route analog returns away from digital clock and serial-data return currents. A symmetric layout reduces gain differences between the simultaneously sampled channels and limits the effect of switching noise coupled through the PCB.
Treat the ADS7254IPW as a 1 MSPS, fully differential acquisition device rather than a general-purpose low-speed ADC. Select the input amplifier and anti-alias filter for the required input bandwidth while preserving the converter's operating range, and provide a stable, low-noise reference network. The two channels should share equivalent filtering and grounding structures when accurate channel-to-channel comparison is required; otherwise, unmatched phase and gain responses can undermine the benefit of simultaneous sampling.
Do not select a replacement solely because it has a 16-pin TSSOP package. ADS7254IPW, ADS7854IPW, and ADS8354IPW are described by TI as pin-compatible, but ADS7854IPW increases resolution from 12 to 14 bits, while ADS8354IPW increases resolution to 16 bits and lowers the listed sampling rate from 1 MSPS to 700 kSPS. Also verify power, reference, interface timing, and analog common-mode requirements before using either family member as a substitute.
合規資訊
The ADS7254IPW listing identifies the exact MPN as RoHS-compliant, lead-free, and green. No exact-part REACH, AEC-Q100, halogen-free, or conflict-minerals declaration was identified.